Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) › from 2015.10
RM3090E _59 Vehicle Exterior _008792 WINDOW / GLASS _0050246 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.

WIRING DIAGRAM

B341195E01
2.563,3.49 4.479,3.833 1.917,0.344 10 Front Power Window Regulator Motor Assembly LH*1 2.552,4.146 4.479,4.49 1.927,0.344 10 Front Power Window Regulator Motor Assembly RH*2 2.573,3.302 4.104,3.5 1.531,0.198 10 J3*1, I3*2 1.875,1.885 2.792,2.083 0.917,0.198 10 DOOR D 3.802,1.594 4.417,1.792 0.615,0.198 10 AUTO 0.448,1.719 2.281,1.917 1.833,0.198 10 from Battery 0.031,0.667 1.865,0.865 1.833,0.198 10 from POWER Relay 1.823,0.854 3.052,1.052 1.229,0.198 10 P/W MAIN 3.75,2.354 4.365,2.552 0.615,0.198 10 DOWN 0.24,3.76 1.927,3.958 1.688,0.198 10 *1: for LHD 0.24,4.229 1.927,4.427 1.688,0.198 10 *2: for RHD 5.406,0.646 5.563,0.844 0.156,0.198 10 B 2.844,1.583 3,1.781 0.156,0.198 10 B 2.615,1.604 2.771,1.802 0.156,0.198 10 2 3.875,2.729 4.49,2.927 0.615,0.198 10 GND 3.969,1.958 4.583,2.156 0.615,0.198 10 UP 5.438,1.677 5.594,1.875 0.156,0.198 10 A 5.427,2.063 5.583,2.26 0.156,0.198 10 U 5.427,2.427 5.583,2.625 0.156,0.198 10 D 5.438,2.823 5.594,3.021 0.156,0.198 10 E 5.156,0.521 5.313,0.719 0.156,0.198 10 6 5.198,1.583 5.354,1.781 0.156,0.198 10 4 5.177,2.354 5.333,2.552 0.156,0.198 10 5 4.792,1.958 5.615,2.177 0.823,0.219 10 8*1, 1*2 5.375,3.302 6.906,3.5 1.531,0.198 10 J5*1, I5*2 5.333,3.5 7.031,4.396 1.698,0.896 10 Power Window Regulator Master Switch Assembly 4.792,2.729 5.75,2.917 0.958,0.188 10 1*1, 9*2 4.292,1.573 4.448,1.771 0.156,0.198 10 4 4.292,1.969 4.583,2.156 0.292,0.188 10 10 4.292,2.354 4.448,2.552 0.156,0.198 10 7 4.281,2.74 4.438,2.938 0.156,0.198 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

When the ECU determines that the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has a malfunction, DTC B2311 is stored.

·

After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.PERFORM ACTIVE TEST USING GTS

DTC is output

2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Driver door power window OFF, UP or DOWN -
HINT:

Up and down movement does not occur if the arrow is not pressed and held.


Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window operates normally.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

3.READ VALUE USING GTS

NG (for LHD)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

NG (for RHD)

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)
3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DATA LIST / ACTIVE TEST

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch being operated
OFF: Driver door power window manual up switch not being operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch being operated
OFF: Driver door power window manual down switch not being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

OK (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

5.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
B341203C01
0.406,0.865 0.719,1.125 0.313,0.26 1.896,0.833 2.125,0.375 2.125,0.375 2.292,0.375 true 1.521,0.813 1.354,0.375 1.354,0.375 1.188,0.375 true 0.875,0.302 1.333,0.5 0.458,0.198 10 false GND 2.365,0.292 2.521,0.49 0.156,0.198 10 false B 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.5,0.927 0.813,1.125 0.313,0.198 10 false J3
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)


Disconnect the front power window regulator motor assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Inspect the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
B276330C01
0.229,0.896 0.479,1.104 0.25,0.208 0.24,1.26 0.49,1.469 0.25,0.208 2.469,1.042 2.656,0.531 2.656,0.531 2.813,0.531 true 1.948,1.052 2.167,0.24 2.167,0.24 2.323,0.24 true 1.01,1.021 0.844,0.51 0.844,0.51 0.698,0.51 true 0.302,0.906 0.615,1.104 0.313,0.198 10 J5 0.104,0.083 0.417,0.281 0.313,0.198 10 *a 2.396,0.198 2.552,0.396 0.156,0.198 10 B 2.875,0.448 3.396,0.656 0.521,0.208 10 E*B 0.406,0.427 0.927,0.635 0.521,0.208 10 E*A 0.302,1.271 0.615,1.469 0.313,0.198 10 I5 0.531,0.917 0.844,1.115 0.313,0.198 10 *A 0.552,1.271 0.865,1.469 0.313,0.198 10 *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J5-1 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
I5-9 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
J5-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
I5-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

OK (for RHD)

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J5 power window regulator master switch assembly connector.


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J5-8 (U) - J3-10 (UP) Always Below 1 Ω
J5-5 (D) - J3-7 (DOWN) Always Below 1 Ω
J5-8 (U) or J3-10 (UP) - Body ground Always 10 kΩ or higher
J5-5 (D) or J3-7 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
B341203C02
0.406,0.865 0.719,1.125 0.313,0.26 1.896,0.833 2.125,0.375 2.125,0.375 2.292,0.375 true 1.521,0.813 1.354,0.375 1.354,0.375 1.188,0.375 true 0.865,0.313 1.323,0.51 0.458,0.198 10 GND 2.365,0.292 2.521,0.49 0.156,0.198 10 B 0.115,0.104 0.427,0.302 0.313,0.198 10 *a 0.5,0.927 0.813,1.125 0.313,0.198 10 I3
*a Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH)


Disconnect the front power window regulator motor assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I3-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the I5 power window regulator master switch assembly connector.


b.

Disconnect the I3 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-1 (U) - I3-10 (UP) Always Below 1 Ω
I5-5 (D) - I3-7 (DOWN) Always Below 1 Ω
I5-1 (U) or I3-10 (UP) - Body ground Always 10 kΩ or higher
I5-5 (D) or I3-7 (DOWN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR