Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0060958 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON.

2.

One of the following conditions is met:

(a) 2 or more of the P, N, NSW, R and D shift lever position signals are on simultaneously.

(b) The P, N, NSW, R and D shift lever position signals are all off simultaneously.

(c) The P, N, NSW or R shift lever position signal is on when the shift lever is in M.

3.

2 seconds for conditions (a) and (c) above, and 60 seconds for condition (b) above

4.

2 trip detection logic


·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch assembly

·

Transmission control switch (Transmission floor shift assembly)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or M).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C277058E22
2.313,6.01 4.333,6.292 2.021,0.281 10 false Transmission Control Switch 2.323,5.792 2.781,5.99 0.458,0.198 10 false G36 0.208,5.167 1.958,5.448 1.75,0.281 10 false from ECU-IG NO. 1 Fuse 0.51,2.688 1.896,2.927 1.385,0.24 10 false from GAUGE Fuse 0.521,1.167 1.729,1.396 1.208,0.229 10 false to ST NO. 1 Relay 2.313,4.365 4.313,4.635 2,0.271 10 false Park/Neutral Position Switch 2.313,4.156 2.813,4.354 0.5,0.198 10 false B101 2.792,1.063 3.125,1.281 0.333,0.219 10 false L 2.563,1.323 2.896,1.542 0.333,0.219 10 false 9 3.552,1.063 3.885,1.281 0.333,0.219 10 false B 3.792,1.313 4.125,1.531 0.333,0.219 10 false 4 3.5,1.656 3.844,1.875 0.344,0.219 10 false DL 3.781,1.917 4.115,2.135 0.333,0.219 10 false 7 3.5,2.26 3.844,2.479 0.344,0.219 10 false NL 3.792,2.521 4.125,2.74 0.333,0.219 10 false 8 3.5,2.865 3.844,3.083 0.344,0.219 10 false RL 3.781,3.125 4.115,3.344 0.333,0.219 10 false 2 3.479,3.469 3.823,3.688 0.344,0.219 10 false PL 3.792,3.719 4.125,3.938 0.333,0.219 10 false 3 2.781,2.552 3.115,2.771 0.333,0.219 10 false RB 2.563,2.833 2.896,3.052 0.333,0.219 10 false 1 5.26,1.177 5.635,1.385 0.375,0.208 10 false B75 5.625,1.198 6.083,1.396 0.458,0.198 10 false NSW 5.313,0.969 5.563,1.198 0.25,0.229 10 false 63 5.313,1.573 5.563,1.802 0.25,0.229 10 false 81 5.26,1.771 5.656,2 0.396,0.229 10 false B75 5.635,1.792 6.094,1.99 0.458,0.198 10 false D 5.271,2.375 5.646,2.594 0.375,0.219 10 false B75 5.271,2.979 5.615,3.198 0.344,0.219 10 false B75 5.26,3.573 5.615,3.813 0.354,0.24 10 false B75 5.26,5.156 5.625,5.385 0.365,0.229 10 false A62 5.313,2.177 5.563,2.406 0.25,0.229 10 false 97 5.302,2.771 5.552,3 0.25,0.229 10 false 79 5.313,3.375 5.563,3.604 0.25,0.229 10 false 99 5.313,4.979 5.563,5.208 0.25,0.229 10 false 41 5.646,2.385 6.104,2.583 0.458,0.198 10 false N 5.635,2.979 6.094,3.177 0.458,0.198 10 false R 5.635,3.583 6.094,3.781 0.458,0.198 10 false P 5.615,5.167 6.073,5.365 0.458,0.198 10 false S 3.563,5.063 3.938,5.24 0.375,0.177 10 false S 2.792,5.063 3.167,5.24 0.375,0.177 10 false IG 3.781,5.302 4.115,5.521 0.333,0.219 10 false 5 2.583,5.313 2.917,5.531 0.333,0.219 10 false 4 5.792,5.896 6.24,6.135 0.448,0.24 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 147,125,126,127,133,128
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GAUGE FUSE - PARK/NEUTRAL POSITION SWITCH)
a.
C330140C30
0.438,0.958 0.885,1.24 0.448,0.281 1.625,1 2.021,0.396 true 2.073,0.313 2.385,0.51 0.313,0.198 10 false RB 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false B101
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B101-1 (RB) - Body ground Ignition switch ON 11 to 14 V
B101-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
C330140C31
0.438,0.958 0.885,1.24 0.448,0.281 2.031,1 2.292,0.396 true 2.354,0.313 2.667,0.51 0.313,0.198 10 false B 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false B101
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B101-4 (B) - Body ground Ignition switch ON 11 to 14 V
B101-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C18
1.823,0.958 2.313,0.385 true 1.594,0.958 1.729,0.385 true 1.271,0.948 0.677,0.385 true 1.906,1.823 1.729,1.292 true 1.344,1.823 1.469,1.292 true 0.865,1.813 1.344,1.281 true 1.406,0.938 1.24,0.365 true 0.104,0.083 0.417,0.281 0.313,0.198 10 *a 0.531,0.302 0.688,0.5 0.156,0.198 10 B 1.813,0.292 2.063,0.49 0.25,0.198 10 RL 2.396,0.302 2.646,0.5 0.25,0.198 10 RB 1.99,1.75 2.24,1.948 0.25,0.198 10 DL 1.115,1.75 1.365,1.948 0.25,0.198 10 NL 0.729,1.75 0.979,1.948 0.25,0.198 10 L 1,0.281 1.25,0.479 0.25,0.198 10 PL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
4 (B) - 9 (L) Shift lever in P Below 1 Ω
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
4 (B) - 9 (L) Shift lever in N Below 1 Ω
1 (RB) - 7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
1 (RB) - 3 (PL) Shift lever not in P 10 kΩ or higher
4 (B) - 9 (L) Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever not in N 10 kΩ or higher
4 (B) - 9 (L) Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever not in D, M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)
a.
C251979C11
0.49,1.042 0.844,1.281 0.354,0.24 2.156,1.802 1.854,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 2.156,1.854 2.573,2.094 0.417,0.24 10 IG 0.552,1.073 0.896,1.292 0.344,0.219 10 G36
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C251980C10
1.375,1.813 1.521,1.281 true 1,1.813 1.302,1.281 true 0.167,0.115 0.479,0.313 0.313,0.198 10 *a 0.917,1.854 1.073,2.042 0.156,0.188 10 S 1.302,1.854 1.688,2.073 0.385,0.219 10 IG
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
a.
C277059C01
1.521,0.25 1.906,0.51 0.385,0.26 1.521,2.51 1.906,2.771 0.385,0.26 2.177,1.948 1.948,1.219 true 1.615,1.958 1.823,1.219 true 0.271,1.969 0.51,1.219 true 0.917,1.948 0.646,1.208 true 2.25,4.313 2.063,3.583 true 0.052,0.052 0.365,0.25 0.313,0.198 10 *a 1.625,0.281 2.083,0.479 0.458,0.198 10 B75 1.615,2.542 2.073,2.74 0.458,0.198 10 A62 2.063,2.021 2.604,2.25 0.542,0.229 10 99 (P) 1.406,2.021 1.969,2.25 0.563,0.229 10 97 (N) 0.073,2.031 0.646,2.281 0.573,0.25 10 79 (R) 0.802,2.031 1.333,2.26 0.531,0.229 10 81 (D) 2.125,4.365 2.677,4.594 0.552,0.229 10 41 (S)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B75-99 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
B75-79 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V
B75-97 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
B75-81 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
A62-41 (S) - Body ground
·

Ignition switch ON

·

Shift lever in M, "+" or "-"


11 to 14 V
B75-99 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
B75-79 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
B75-97 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
B75-81 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
A62-41 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in M, "+" or "-"


Below 1 V



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the B101 park/neutral position switch connector.


b.

Disconnect the B75 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B101-4 (B) - B75-63 (NSW) Always Below 1 Ω
B101-4 (B) - Body ground Always 10 kΩ or higher
B75-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR