*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points in the problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Running conditions, driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check the ECUs connected to the CAN bus.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| No Malfunction appears |
| Malfunction appears |
No Malfunction appears
Malfunction appears
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
Refer to DTC Check / Clear.
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output |
DTCs are not output
DTCs are output
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Refer to Problem Symptoms Table.
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| Malfunctioning parts are not confirmed |
| Malfunctioning parts are confirmed |
Malfunctioning parts are not confirmed
Malfunctioning parts are confirmed
Refer to Data List / Active Test.
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| Malfunctioning parts are not confirmed |
| Malfunctioning parts are confirmed |
Malfunctioning parts are not confirmed
Malfunctioning parts are confirmed
Refer to Terminals of ECM.
Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>TERMINALS OF ECM
| Result |
|---|
| OK |
| NG |
OK
NG
Refer to Symptom Simulation.
for CCo: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>CHECK FOR INTERMITTENT PROBLEMS
for DPF: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK FOR INTERMITTENT PROBLEMS
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT