Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR(for 4WD/AWD) › from 2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0049570 REAR SPEED SENSOR(for 4WD/AWD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR(for 4WD/AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 89546 1.INSTALL REAR SPEED SENSOR LH

NOTICE:

To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.


a.
C274703E02
2.281,1.583 2.438,1.781 0.156,0.198 10 A 2.51,1.75 2.667,1.948 0.156,0.198 10 B 2.365,2.406 2.521,2.604 0.156,0.198 10 C 0.479,3.021 0.635,3.219 0.156,0.198 10 D

Install the sensor labeled A with the bolt labeled B.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Keep the sensor tip and sensor installation hole free from foreign matter.

·

To prevent interference with the bearing rotor, do not rotate the sensor body when inserting the sensor body or after inserting the sensor body.




b.

Install the sensor clamp labeled C with the nut labeled D.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.
C274702C01
0,0 0.313,0.156 0.313,0.156 10 *a 0.448,2.375 0.604,2.573 0.156,0.198 10 E 1.24,2.927 1.396,3.125 0.156,0.198 10 F 2.083,0.604 2.24,0.802 0.156,0.198 10 G 3.042,0.448 3.198,0.646 0.156,0.198 10 H 1.771,2.615 1.927,2.813 0.156,0.198 10 E 2.594,2.396 2.75,2.594 0.156,0.198 10 F
*a Painted Line


Install the sensor clamps labeled E with the 2 nuts labeled F.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamps.



d.

Install the sensor clamp labeled G with the bolt labeled H.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the sensor wire when installing the clamp.



e.
C279263C02
0.958,1.719 0.958,2.688 false 2.5,2 2.5,2.708 2.5,2.708 2.74,2.708 false 1.792,1.458 2.219,1.094 2.219,1.094 2.49,1.094 false 2.542,1.031 2.781,1.188 0.24,0.156 10 *1 2.781,2.635 2.99,2.813 0.208,0.177 10 *2 0.906,2.74 1.094,2.917 0.188,0.177 10 *3 1.781,0.375 2.094,0.531 0.313,0.156 10 *a
*1 Grommet
*2 Connector
*3 Band Clamp
*a Inside of Vehicle


Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel house.

NOTICE:

Make sure the grommet band clamp remains on the outside of the vehicle.



f.

Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.

C274704C03
1.573,0.573 1.74,0.771 0.167,0.198 10 *a 4.771,2.24 4.938,2.427 0.167,0.188 10 *b 5.427,2.229 5.594,2.417 0.167,0.188 10 *b
*a Outside of Vehicle *b 30°


NOTICE:
·

When pulling out the grommet, do not grip the sensor wire.

·

Fix the grommet in place within the range shown in the illustration.




g.

Connect the speed sensor connector.


Hide 64740C 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION

HINT:

Refer to the procedures from the installation of the deck trim side panel LH up until the installation of the rear door scuff plate LH.


Hide 3.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)