Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine)
RM3090E _54 Brake _008768 BRAKE SYSTEM (OTHER) _0256589 VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(When Using the Engine Support Bridge for AD Series Engine)  REMOVAL  


PROCEDURE

Hide 85192 1.REMOVE WINDSHIELD WIPER ARM COVER

Hide 2.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 55781E 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 17705 6.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 7.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 51443 9.REMOVE REAR ENGINE UNDER COVER RH

Hide 16470 11.DISCONNECT RADIATOR RESERVE TANK ASSEMBLY

Hide 12.INSTALL ENGINE SUPPORT BRIDGE

a.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10020  

C353204C01
2.083,7.167 2,7.167 2,7.167 1.833,6.417 true 1.25,5.333 1.667,5.333 true 5.417,5.5 5.833,5.5 true 5.167,7.25 5.25,7.25 5.25,7.25 5.417,6.5 true 2.333,7.896 2.25,7.896 2.25,7.896 2.167,8.313 true 1.583,7.927 1.5,7.927 1.5,7.927 1.333,8.365 true 4.833,7.927 4.917,7.927 4.917,7.927 5,8.323 true 5.646,7.927 5.729,7.927 5.729,7.927 5.813,8.365 true 1.073,5.229 1.385,5.385 0.313,0.156 10 false *a 2.146,7.073 2.458,7.229 0.313,0.156 10 false *b 0.896,1.625 1.208,1.781 0.313,0.156 10 false *c 2.802,7.313 3.115,7.469 0.313,0.156 10 false *d 1.26,7.302 1.573,7.458 0.313,0.156 10 false *e 0.323,0.198 0.635,0.354 0.313,0.156 10 false *f 6.74,0.188 7.052,0.344 0.313,0.156 10 false *f 6.479,1.615 6.792,1.771 0.313,0.156 10 false *c 5.885,5.417 6.094,5.635 0.208,0.219 10 true *a 4.979,7.156 5.292,7.313 0.313,0.156 10 false *b 6.24,7.323 6.552,7.479 0.313,0.156 10 false *e 4.698,7.333 5.01,7.49 0.313,0.156 10 false *d 4.656,7.833 4.969,7.99 0.313,0.156 10 false *b 5.479,7.823 5.792,7.979 0.313,0.156 10 false *b 2.385,7.802 2.698,7.958 0.313,0.156 10 false *b 1.625,7.833 1.938,7.99 0.313,0.156 10 false *b
*a Support Shaft *b Side Member
*c Front Side *d Incorrect
*e Correct *f Front Suspension Nut


CAUTION:
·
C312303C04
1.761,2.043 1.964,2.235 0.203,0.191 10 *a 0.175,1.885 0.378,2.076 0.203,0.191 10 *a 0.57,0.075 0.773,0.266 0.203,0.191 10 *c 2.261,0.075 2.464,0.266 0.203,0.191 10 *d 0.136,2.338 0.340,2.530 0.203,0.191 10 *b 1.74,2.46 1.944,2.651 0.203,0.191 10 *b 0.405,1.987 0.51,1.987 0.51,1.987 0.797,2.456 false 0.35,2.426 0.465,2.426 0.465,2.426 0.781,2.709 false 1.991,2.133 2.078,2.133 2.078,2.133 2.475,2.448 false 1.971,2.545 2.091,2.545 2.091,2.545 2.477,2.723 false
*a Fuse Shackle
*b Shackle (A)
*c Correct
*d Incorrect


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·
C353205C01
1.729,1.156 2.167,0.75 2.167,0.75 2.25,0.75 true 2.271,0.656 2.5,0.833 0.229,0.177 10 true *a 0.542,2.135 0.854,2.292 0.313,0.156 10 false *b 2.01,2.146 2.323,2.302 0.313,0.156 10 false *c
*a Fuse Bolt
*b Correct
*c Incorrect


Make sure the fuse bolt is not deformed.



NOTICE:
·

Prevent SST from contacting the vehicle body or windshield.

·

Lightly shake SST by hand to make sure it is securely installed while performing work.

·

Set the support shafts on level surfaces.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.




b.
C353206C01
0.417,1.479 0.667,1.167 0.667,1.167 0.75,1.167 false 0.99,1.979 1.156,1.833 1.156,1.833 1.24,1.833 false 0.958,2.5 1.167,2.583 1.167,2.583 1.25,2.583 true 0.948,2.865 0.823,3.115 0.823,3.115 0.74,3.115 true 1.26,1.75 1.573,1.906 0.313,0.156 10 false *a 0.802,1.083 1.115,1.24 0.313,0.156 10 false *b 0.573,3.031 0.74,3.219 0.167,0.188 10 true *c 1.302,2.49 1.469,2.688 0.167,0.198 10 true *d
*a Support Shaft
*b Sub Beam
*c Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height and make the SST sub beams parallel to the ground.


c.

Connect the chain to the division bar with the shackle at the position shown in the illustration.

C353207C01
1.24,2.708 1.771,3.031 1.771,3.031 1.938,3.031 true 5.958,2.625 5.417,3.021 5.417,3.021 5.323,3.021 true 0.667,1.333 0.75,1.333 0.75,1.333 1.083,2.417 true 6.667,1.417 6.583,1.417 6.583,1.417 6.25,2.302 true 0.917,3.5 1,3.5 1,3.5 1.333,3.104 true 5.333,3.5 5.417,3.5 5.417,3.5 5.771,3.167 true 0.75,3.417 0.948,3.583 0.198,0.167 10 true *1 5.177,3.417 5.375,3.604 0.198,0.188 10 true *2 0.5,1.25 0.813,1.406 0.313,0.156 10 false *a 1.969,2.969 2.135,3.135 0.167,0.167 10 true *b 5.104,2.938 5.281,3.135 0.177,0.198 10 true *b 6.708,1.323 7.021,1.479 0.313,0.156 10 false *a 6.094,2.615 6.198,2.781 0.104,0.167 10 true 1 6.021,2.875 6.125,3.042 0.104,0.167 10 true 2
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle



d.

Connect the division bar and No. 1 engine hanger with the shackle.


e.

Connect the 2nd link of the chain to the No. 2 engine hanger.


f.

Make sure the distance between A and B is 120 mm (4.72 in.) or more.

C353208C01
1.552,0.76 1.781,0.927 0.229,0.167 10 true *a 0.865,0.802 1.073,0.969 0.208,0.167 10 true *b 0.542,0.969 0.698,1.167 0.156,0.198 10 true A 0.521,0.583 0.677,0.781 0.156,0.198 10 true B
*a Chain Block Assembly *b 120 mm (4.72 in.) or more



g.

Adjust the position of the chain block assembly so that the chain is perpendicular to the SST main beam and sub beams as shown in the illustration.

C353209C01
1.115,1.615 1.188,1.615 1.188,1.615 1.844,2.125 true 6.188,1.698 6.104,1.698 6.104,1.698 5.531,2.167 true 3.979,1.469 3.896,1.469 3.896,1.469 3.563,1.302 true 4.354,0.625 4.271,0.625 4.271,0.625 3.844,0.927 true 4.01,1.365 4.323,1.521 0.313,0.156 10 false *a 4.427,0.531 4.74,0.688 0.313,0.156 10 false *b 0.927,1.51 1.24,1.667 0.313,0.156 10 false *c 1.729,0.448 2.042,0.604 0.313,0.156 10 false *d 5.479,0.448 5.792,0.604 0.313,0.156 10 false *e 1.313,3.563 1.625,3.719 0.313,0.156 10 false *f 4.729,3.573 5.021,3.802 0.292,0.229 10 false *g 3.49,0.458 3.802,0.615 0.313,0.156 10 false *h 5.656,1.479 5.969,1.677 0.313,0.198 10 true *i 1.521,1.458 1.719,1.656 0.198,0.198 10 true *i 6.25,1.604 6.563,1.76 0.313,0.156 10 false *c
*a Chain Block Assembly *b Main Beam
*c Sub Beam *d Dimension (A)
*e Dimension (B) *f Correct
*g Incorrect *h Right to Left Adjustment
*i Front to Rear Adjustment - -


CAUTION:

To prevent the engine with automatic transaxle assembly from falling, make sure that the dimension (A) and dimension (B) are equal.



h.

Tighten the 6 wing bolts and 2 bolts.

C353210

Torque:
for bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)


i.
C353211C01
0,0 0,0 false
V113147

Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C316805C04
1.208,0.958 1.479,0.958 false 3.031,0.958 3.188,0.958 false 0.49,2.333 0.49,2.583 false 2.313,2.479 2.313,2.729 false 0.365,1.365 0.125,1.604 0.125,1.604 0.125,1.844 true 2.188,1.448 1.948,1.688 1.948,1.688 1.948,1.927 true 3.188,0.865 3.375,1.073 0.188,0.208 10 false *a 1.5,0.875 1.688,1.083 0.188,0.208 10 false *a 0.052,1.833 0.24,2.042 0.188,0.208 10 false *c 0.406,2.583 0.594,2.792 0.188,0.208 10 false *b 1.875,1.917 2.063,2.125 0.188,0.208 10 false *c 2.229,2.729 2.417,2.938 0.188,0.208 10 false *b 0.625,0.448 0.813,0.656 0.188,0.208 10 false *d 2.448,0.469 2.635,0.677 0.188,0.208 10 false *e
*a Chain Block Assembly
*b Suspension Ring
*c Roller
*d Incorrect
*e Correct


If the suspension ring contacts the roller of the chain block assembly, the chain block assembly may be damaged. Do not tighten the chain block assembly excessively.


NOTICE:
·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Do not shake the engine with automatic transaxle assembly excessively while it is being suspended.




Hide 12305 13.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

a.
C353212

Disconnect the 2 clamps from the suction tube sub-assembly.


b.
C354909

Remove the 2 nuts, 5 bolts and engine mounting insulator sub-assembly RH.

NOTICE:

Do not damage the suction tube sub-assembly.



Hide 29300 14.REMOVE VACUUM PUMP ASSEMBLY

a.
C261794

Slide the clip and disconnect the 2 vacuum hoses.


b.

Remove the 3 bolts and vacuum pump.


c.

Remove the 2 O-rings from the vacuum pump.