Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2016.08
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050374 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2205  Kick Sensor Circuit  


DESCRIPTION

B2205 is output when the multiplex network door ECU detects that the kick door control sensor is stuck on.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2205 Kick Sensor Circuit One of the following conditions is met for approximately 60 seconds or more:
·

The multiplex network door ECU detects a kick door control sensor short circuit

·

Multiplex network door ECU malfunction

·

Kick door control sensor malfunction


·

Kick door control sensor

·

Multiplex network door ECU

·

Harness or connector



WIRING DIAGRAM

E350290E01
4.563,1.958 5.021,2.156 0.458,0.198 10 false U29 4.583,2.135 7.156,2.396 2.573,0.26 10 false Multiplex Network Door ECU 4.833,1.104 5.448,1.302 0.615,0.198 10 false KSIN 2.031,1.104 2.646,1.302 0.615,0.198 10 false KSOT 4.552,0.979 4.865,1.177 0.313,0.198 10 false 14 2.573,0.979 2.885,1.177 0.313,0.198 10 false 2 1.198,1.969 1.656,2.167 0.458,0.198 10 false S11 1.208,2.135 3.781,2.396 2.573,0.26 10 false Kick Door Control Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the kick door control sensor is not damaged.

·

Before troubleshooting, be sure to read Precautions for Touchless Power Back Door.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>PRECAUTION

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

After performing work, using the GTS, read the Data List item "Kick Sensor Connection" and check that the kick door control sensor is connected.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC is not output A
DTC B2205 is output B



A

B

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Disconnect the S11 kick door control sensor connector.


b.

Wait for approximately 60 seconds.


c.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

d.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC is not output A
DTC B2205 is output B



A

REPLACE KICK DOOR CONTROL SENSOR

B

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR)
a.

Disconnect the U29 multiplex network door ECU connector.


b.

Disconnect the S11 kick door control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U29-14 (KSIN) or S11-2 (KSOT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR