Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2016.08
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050374 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Operated Using Kick Sensor  


DESCRIPTION

Signals from the kick door control sensor are sent to the multiplex network door ECU. If the power back door system does not operate, there may be a malfunction in the kick door control sensor circuit.

WIRING DIAGRAM

E350291E01
2.156,1.615 2.615,1.813 0.458,0.198 10 false S11 2.167,1.75 3.333,2.115 1.167,0.365 10 false Kick Door Control Sensor 0.813,2.365 4.479,2.563 3.667,0.198 10 false : CAN Communication Line 1.375,0.948 2.906,1.146 1.531,0.198 10 false ECU-B NO.1 0.25,0.771 2.083,0.969 1.833,0.198 10 false from Battery 2.25,0.781 2.406,0.979 0.156,0.198 10 false B 2.271,1.333 2.729,1.531 0.458,0.198 10 false GND 2.031,0.656 2.188,0.854 0.156,0.198 10 false 1 2.031,1.188 2.188,1.385 0.156,0.198 10 false 3 3.354,0.938 3.51,1.135 0.156,0.198 10 false 2 3.667,0.938 3.979,1.135 0.313,0.198 10 false 14 2.844,1.063 3.458,1.26 0.615,0.198 10 false KSOT 4,1.073 4.615,1.271 0.615,0.198 10 false KSIN 3.594,2.146 7.156,2.344 3.563,0.198 10 false Multiplex Network Door ECU 3.594,1.958 4.052,2.156 0.458,0.198 10 false U29 5.594,1.979 7.156,2.365 1.563,0.385 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the "Kick Sensor Function" customize setting is set to "ON".

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS

·

Before troubleshooting, be sure to read Precautions for Touchless Power Back Door.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>PRECAUTION

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

After performing work, using the GTS, read the Data List item "Kick Sensor Connection" and check that the kick door control sensor is connected.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Kick Sensor Error Status of the kick door control sensor error Normal or Error Normal: Kick door control sensor is normal
Error: Kick door control sensor is abnormal
-
Body Electrical > Back Door > Data List
Tester Display
Kick Sensor Error
50003 159 77
OK:

On the GTS, Normal is displayed.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE KICK DOOR CONTROL SENSOR

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Kick Sensor Detection Status of the kick door control sensor detection OFF or ON OFF: Kick door control sensor not detecting a foot
ON: Kick door control sensor detecting a foot
-
Body Electrical > Back Door > Data List
Tester Display
Kick Sensor Detection
50003 159 76
OK:

On GTS screen, item changes between ON and OFF according to above chart.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

4.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - BATTERY AND BODY GROUND)
a.
E137787C01
1.51,0.104 1.875,0.396 0.365,0.292 1.135,1.573 1.552,1.156 true 2.24,1.604 1.917,1.146 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 1.563,0.167 1.875,0.365 0.313,0.198 10 false S11 1.031,1.615 1.344,1.813 0.313,0.198 10 false B 2.24,1.677 2.688,1.875 0.448,0.198 10 false GND
*a Front view of wire harness connector
(to Kick Door Control Sensor)


Disconnect the kick door control sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S11-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - MULTIPLEX NETWORK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (KICK DOOR CONTROL SENSOR - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the S11 kick door control sensor connector.


b.

Disconnect the U29 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-2 (KSOT) - U29-14 (KSIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MULTIPLEX NETWORK DOOR ECU
a.

Disconnect the S11 kick door control sensor connector.


b.

Remove the multiplex network door ECU with the connector(s) still connected.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL


c.
E356076C01
1.521,0.281 1.938,0.521 0.417,0.24 0.917,1.688 1.375,1.177 true 0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 1.604,0.313 2.063,0.51 0.458,0.198 10 false U29 0.75,1.729 1.208,1.927 0.458,0.198 10 false KSIN 0.146,4.083 0.604,4.281 0.458,0.198 10 false GND
*a Component with harness connected
(Multiplex Network Door ECU)


Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection U29-14 (KSIN) - Body ground
Tool Setting 2 V/DIV., 50 ms./DIV.
Vehicle Condition Kick door control sensor not detecting a foot

OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE KICK DOOR CONTROL SENSOR

NG

REPLACE MULTIPLEX NETWORK DOOR ECU