Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3090E _56 Audio / Visual / Telematics _057499 TELEMATICS _0279690 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1573  Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Short in Telephone Antenna Circuit Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

Harness or connector


B15CB Telephone Antenna Disconnected Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

Harness or connector



WIRING DIAGRAM

E355983E01
5.49,2.573 6.969,2.833 1.479,0.26 10 false Telematics Transceiver 2.083,2.406 3.302,2.813 1.219,0.406 10 false No. 3 Antenna Cord Sub-assembly 0.375,2.385 1.844,2.813 1.469,0.427 10 false No. 1 Amplifier Antenna Assembly 5.479,2.396 5.813,2.635 0.333,0.24 10 false M42 5.646,1.281 6.042,1.521 0.396,0.24 10 false ANT1 3.281,1.281 3.615,1.521 0.333,0.24 10 false M44 3.281,1.979 3.615,2.219 0.333,0.24 10 false M44 1.833,1.271 2.167,1.51 0.333,0.24 10 false A 1.844,1.979 2.177,2.219 0.333,0.24 10 false A 1.844,1.083 2.177,1.323 0.333,0.24 10 false 4 1.813,1.781 2.146,2.021 0.333,0.24 10 false 4a 3.375,1.083 3.708,1.323 0.333,0.24 10 false 2 3.344,1.781 3.677,2.021 0.333,0.24 10 false 2a 5.427,1.177 5.76,1.417 0.333,0.24 10 false 1 5.385,1.865 5.719,2.104 0.333,0.24 10 false 1a

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Remove the No. 1 amplifier antenna assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 1 Amplifier Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350951C11
1.646,0.271 2.042,0.552 0.396,0.281 1.271,1.563 1.688,1.521 true 1.073,3.396 1.604,3.563 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.073,1.479 1.385,1.677 0.313,0.198 10 false 4a 0.865,3.302 1.177,3.5 0.313,0.198 10 false 2a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 0.177,2.635 0.49,2.833 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - 2 Always Below 1 Ω
A-4a - 2a Always Below 1 Ω
A-4 or 2 - Body ground Always 10 kΩ or higher
A-4a or 2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 3 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 3 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)
a.
E350974C01
1.615,2.688 2.052,2.979 0.438,0.292 1.563,0.375 2,0.667 0.438,0.292 1.198,3.917 1.75,3.708 true 1.958,3.802 2.292,3.969 true 2.292,1.198 2.635,1.365 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.667,0.448 1.99,0.698 0.323,0.25 10 false M44 1.708,2.75 2.323,2.948 0.615,0.198 10 false M42 0.813,3.875 1.229,4.094 0.417,0.219 10 false ANT1 2.333,3.927 2.646,4.125 0.313,0.198 10 false 1a 2.698,1.375 3.01,1.573 0.313,0.198 10 false 2a 0.188,2.635 0.5,2.833 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the telematics transceiver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M44-2 - M42-1 (ANT1) Always Below 1 Ω
M44-2a - M42-1a Always Below 1 Ω
M44-2 or M42-1 (ANT1) - Body ground Always 10 kΩ or higher
M44-2a or M42-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT