Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3090E _56 Audio / Visual / Telematics _057499 TELEMATICS _0279690 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 Short in GPS Antenna Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit)
·

Telematics transceiver

·

Antenna divider

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

Harness or connector


B15C1 Open in GPS Antenna Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit)
·

Telematics transceiver

·

Antenna Divider

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

Harness or connector



WIRING DIAGRAM

E355984E01
0.198,2.104 1.656,2.531 1.458,0.427 10 false No. 1 Amplifier Antenna Assembly 1.708,1.083 1.865,1.281 0.156,0.198 10 false A 1.708,1.729 1.865,1.927 0.156,0.198 10 false A 2.969,1.083 3.302,1.333 0.333,0.25 10 false M44 2.979,1.719 3.313,1.969 0.333,0.25 10 false M44 4.063,2.302 5.146,2.646 1.083,0.344 10 false Antenna Divider 4.052,2.135 4.385,2.385 0.333,0.25 10 false M41 1.823,2.125 3.042,2.552 1.219,0.427 10 false No. 3 Antenna Cord Sub-assembly 5.615,2.302 7,2.542 1.385,0.24 10 false Telematics transceiver 5.604,2.135 5.938,2.385 0.333,0.25 10 false M43 5.792,1.083 6.198,1.344 0.406,0.26 10 false ANT2 1.719,0.906 1.875,1.104 0.156,0.198 10 false 5 1.698,1.542 1.896,1.76 0.198,0.219 10 false 5a 3.063,0.906 3.219,1.104 0.156,0.198 10 false 1 3.021,1.542 3.208,1.771 0.188,0.229 10 false 1a 3.906,1 4.063,1.198 0.156,0.198 10 false 6 3.865,1.635 4.052,1.865 0.188,0.229 10 false 6a 5.073,0.99 5.229,1.188 0.156,0.198 10 false 5 5.063,1.625 5.25,1.854 0.188,0.229 10 false 5a 5.583,0.99 5.74,1.188 0.156,0.198 10 false 1 5.542,1.625 5.729,1.854 0.188,0.229 10 false 1a

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350951C05
1.646,0.271 2.042,0.552 0.396,0.281 2.021,1.5 2.438,1.458 true 2.198,3.583 2.667,3.417 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.479,1.375 2.792,1.573 0.313,0.198 10 false 5a 2.708,3.344 3.021,3.542 0.313,0.198 10 false 1a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 0.146,2.542 0.458,2.74 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-5 - 1 Always Below 1 Ω
A-5a - 1a Always Below 1 Ω
A-5 or 1 - Body ground Always 10 kΩ or higher
A-5a or 1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 3 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 3 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)
a.
E350976C01
1.583,0.354 2.021,0.656 0.438,0.302 1.583,2.563 2.021,2.865 0.438,0.302 1.083,1.292 1.313,1.177 true 2.781,3.625 2.917,3.969 true 1.677,0.427 2,0.688 0.323,0.26 10 false M44 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.677,2.625 2.021,2.844 0.344,0.219 10 false M41 0.896,1.208 1.135,1.417 0.24,0.208 10 false 1a 2.938,3.979 3.177,4.188 0.24,0.208 10 false 6a 0.208,2.51 0.521,2.708 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna divider.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M44-1 - M41-6 Always Below 1 Ω
M44-1a - M41-6a Always Below 1 Ω
M44-1 or M41-6 - Body ground Always 10 kΩ or higher
M44-1a or M41-6a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA DIVIDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ANTENNA DIVIDER

b.
E241596C10
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.406,1.427 1.49,1.771 1.49,1.771 1.74,1.771 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.813,1.688 2.24,1.865 0.427,0.177 10 false 5a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
5 - 6 Always Below 1 Ω
5 - 5a Always 10 kΩ or higher
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - TELEMATICS TRANSCEIVER)

NG

5.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - TELEMATICS TRANSCEIVER)
a.
E350977C05
1.635,2.74 2.063,3.052 0.427,0.313 1.573,0.438 2,0.75 0.427,0.313 2.531,2.021 2.302,1.615 true 2.292,4.104 2.021,3.885 true 1.792,3.865 1.438,3.875 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.719,2.813 2.083,3.01 0.365,0.198 10 false M43 2.583,2.01 2.948,2.208 0.365,0.198 10 false 5a 2.354,4.063 2.719,4.26 0.365,0.198 10 false 1a 1.667,0.5 2.031,0.698 0.365,0.198 10 false M41 1.063,3.792 1.427,3.99 0.365,0.198 10 false ANT2 0.146,2.698 0.458,2.896 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Antenna Divider)
*b Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna connector from the antenna divider.


b.

Disconnect the antenna connector from the telematics transceiver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-5 - M43-1 (ANT2) Always Below 1 Ω
M41-5a - M43-1a Always Below 1 Ω
M41-5 or M43-1 (ANT2) - Body ground Always 10 kΩ or higher
M41-5a or M43-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

7.REPLACE TELEMATICS TRANSCEIVER
7.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT