Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode
·

Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "DCM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside telematics transceiver

·

Telematics transceiver CAN branch wire or connector

·

Telematics transceiver



WIRING DIAGRAM

C306914E55
5.656,1.031 6.125,1.188 0.469,0.156 10 false CANP 5.646,1.542 6.115,1.698 0.469,0.156 10 false CANN 5.656,2.385 6.125,2.542 0.469,0.156 10 false +B 5.646,3.156 6.115,3.313 0.469,0.156 10 false IG2 5.656,3.875 6.125,4.031 0.469,0.156 10 false ACC 5.656,4.396 6.125,4.552 0.469,0.156 10 false E 5.323,0.875 5.542,1.073 0.219,0.198 10 false 15 5.313,1.427 5.542,1.583 0.229,0.156 10 false 16 5.417,3.01 5.615,3.198 0.198,0.188 10 false 7 5.396,2.25 5.594,2.438 0.198,0.188 10 false 1 5.417,3.74 5.615,3.927 0.198,0.188 10 false 8 5.406,4.26 5.604,4.448 0.198,0.188 10 false 4 1.521,0.875 1.677,1.073 0.156,0.198 10 false 1 1.521,1.417 1.75,1.573 0.229,0.156 10 false 12 0.323,1.875 0.792,2.052 0.469,0.177 10 false M39 0.333,2.042 3.24,2.24 2.906,0.198 10 false No. 13 CAN Junction Connector 5.302,4.865 5.698,5.031 0.396,0.167 10 false M38 5.302,5.031 6.844,5.281 1.542,0.25 10 false Telematics Transceiver 4.031,2.177 4.719,2.396 0.688,0.219 10 false MAYDAY 4.219,2.917 5.146,3.094 0.927,0.177 10 false A/B 4.188,3.656 5.271,3.833 1.083,0.177 10 false ACC 2.219,2.365 3.104,2.583 0.885,0.219 10 false from Battery 2.146,3.104 3.51,3.333 1.365,0.229 10 false from IG2 Relay 1.99,3.844 3.063,4.042 1.073,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEMATICS TRANSCEIVER CAN BRANCH WIRE)
a.
C300829C75
0.167,1 0.583,1.25 0.417,0.25 1.813,1.125 1.583,0.417 1.583,0.417 1.417,0.417 true 1.917,1.115 2.167,0.417 2.167,0.417 2.333,0.417 true 0.094,0.094 0.417,0.354 0.323,0.26 10 false *a 0.24,1.052 0.573,1.24 0.333,0.188 10 false M38 1.01,0.354 1.51,0.583 0.5,0.229 10 false CANP 2.396,0.354 2.906,0.583 0.51,0.229 10 false CANN
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-15 (CANP) - M38-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE TELEMATICS TRANSCEIVER CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)
a.
C300829C76
1.49,0.25 1.906,0.5 0.417,0.25 0.927,0.938 0.698,0.5 0.698,0.5 0.521,0.5 true 0.927,1.188 0.667,1.917 0.667,1.917 0.5,1.917 true 1.063,1.188 1.24,1.917 1.24,1.917 1.406,1.917 true 2.26,0.917 2.563,0.5 2.563,0.5 2.75,0.5 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.302 1.938,0.5 0.365,0.198 10 false M38 0.323,0.448 0.688,0.688 0.365,0.24 10 false +B 0.26,1.854 0.635,2.083 0.375,0.229 10 false IG2 1.469,1.844 1.906,2.083 0.438,0.24 10 false ACC 2.792,0.448 3.104,0.708 0.313,0.26 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M38-1 (+B) - Body ground Always 11 to 14 V
M38-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
M38-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR