Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) D

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  DIAGNOSIS SYSTEM  


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

Central gateway ECU


ii.

DLC3



b.

Bus 2

i.

ECM


ii.

Central gateway ECU


iii.

Power steering ECU assembly


iv.

Air conditioning amplifier assembly


v.

Airbag sensor assembly


vi.

Spiral with sensor cable sub-assembly (steering angle sensor)


vii.

Certification ECU (smart key ECU assembly)*1


viii.

4WD ECU assembly*2


ix.

Brake actuator assembly (skid control ECU)


x.

Main body ECU (multiplex network body ECU)


xi.

Engine stop and start ECU*3


xii.

Combination meter assembly

*1: w/ Entry and Start System

*2: for 4WD/AWD

*3: w/ Stop and Start System




c.

Bus 3

i.

Central gateway ECU


ii.

Radio and display receiver assembly*1


iii.

Telematics transceiver*2

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Telematics Transceiver




d.

Bus 5

i.

Central gateway ECU


ii.

Parking assist ECU*1


iii.

Driving support ECU assembly*2


iv.

Clearance warning ECU assembly*3


v.

Forward recognition camera*2


vi.

Blind spot monitor sensor LH*4


vii.

Millimeter wave radar sensor assembly*2


viii.

Television camera assembly*5

*1: w/ Panoramic View Monitor System

*2: w/ Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

*4: w/ Blind Spot Monitor System

*5: w/ Parking Assist Monitor System (for Camera built-in ECU)




e.

Sub Bus 1 (w/ Power Back Door System)

i.

Main body ECU (multiplex network body ECU)


ii.

Multiplex network door ECU


iii.

Position control ECU and switch assembly*

*: w/ Seat Memory




f.

Local Bus (w/ Pre-crash Safety System)

i.

Driving support ECU assembly


ii.

Forward recognition camera


iii.

Millimeter wave radar sensor assembly




CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>SYSTEM DIAGRAM



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU, the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU and V bus (the bus that connects the DLC3 to the central gateway ECU) for malfunctions.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch on (IG) (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Open in both CAN branch lines of HV on the bus 4

C360877C01
6.292,6.135 6.604,6.333 0.313,0.198 10 false *f 1,1.115 1.313,1.313 0.313,0.198 10 false *a 1.01,2.292 1.323,2.49 0.313,0.198 10 false *b 1.708,3.542 2.021,3.74 0.313,0.198 10 false *c 5.479,0.625 5.792,0.823 0.313,0.198 10 false : *e 1.021,4.438 1.333,4.635 0.313,0.198 10 false *d 0.448,2.542 1.292,2.781 0.844,0.24 10 false CGW 2.063,0.719 2.906,0.958 0.844,0.24 10 false F-MGC 3.75,0.719 4.594,0.958 0.844,0.24 10 false HVB 4.302,0.719 5.146,0.958 0.844,0.24 10 false R-MGC 1.948,1.302 2.792,1.542 0.844,0.24 10 false CAN J/C 1 3.865,1.302 4.708,1.542 0.844,0.24 10 false CAN J/C 2 6.406,1.302 6.906,1.542 0.5,0.24 10 false ENG 1.865,1.885 2.708,2.125 0.844,0.24 10 false HV 2.438,1.875 3.281,2.115 0.844,0.24 10 false BRK 1.958,2.469 2.802,2.708 0.844,0.24 10 false CAN J/C 3 3.896,2.469 4.74,2.708 0.844,0.24 10 false CAN J/C 4 5.719,2.469 6.219,2.698 0.5,0.229 10 false SRS 1.844,3.125 2.344,3.354 0.5,0.229 10 false MB 3.76,3.073 4.26,3.302 0.5,0.229 10 false EPS 4.385,3.073 4.885,3.302 0.5,0.229 10 false STR 2.917,3.906 3.76,4.146 0.844,0.24 10 false CAN J/C 5 4.813,3.906 5.656,4.146 0.844,0.24 10 false CAN J/C 6 6.458,3.906 6.771,4.146 0.313,0.24 10 false ST 1.531,4.573 2.031,4.802 0.5,0.229 10 false DLC3 3.052,4.51 3.552,4.74 0.5,0.229 10 false MIR-R 4.979,4.51 5.479,4.74 0.5,0.229 10 false MIR-L
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.



c.

If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor whose background color is red) is suspected.

Example: Open in a CAN branch line for HV on the bus 4

C360878C01
6.365,1.135 6.677,1.333 0.313,0.198 10 false *a 6.354,1.625 6.667,1.823 0.313,0.198 10 false *c 0.708,1.771 1.021,1.969 0.313,0.198 10 false *c 0.708,1.198 1.021,1.396 0.313,0.198 10 false *b
*a Background color is red *b Background color intermittently becomes yellow or red
*c Not displayed or background color is yellow or red - -


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
Bus White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4

·

No ECUs or sensors are connected to the bus.*5


Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 White Communication has been normal.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Not communicating since the start of the CAN bus check

·

Communication occurred at least once since the start of the CAN bus check, but is currently not occurring.


Not displayed Either of the following:
·

The gateway function equipped ECU cannot communicate with the central gateway ECU.*6

·

No ECUs or sensors are connected to the sub bus.*7



·

Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.

·

*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.

·

*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.

·

*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.

·

*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.

·

*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.

·

*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.

·

*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of HV is also unstable. In addition, in this example, MB is equipped with a gateway function. Therefore, communication is also unstable between the Sub bus ECUs of MB and the bus 4.

·

The example in the illustration shows that HV has a red background color on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of HV is suspected.



d.

If a communication error is indicated on both the bus 4 and Sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the bus 4 first.

Example: Open in both CAN branch lines of MB on the bus 4

C360879C01
0.708,1.292 1.021,1.448 0.313,0.156 10 false *a 0.708,1.781 1.021,1.938 0.313,0.156 10 false *b 6.344,1.635 6.656,1.792 0.313,0.156 10 false *b
*a Background color is red *b Not displayed


HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the bus after connecting the GTS to the DLC3. As for sub bus, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that MB has a gateway function and a communication stop in MB is suspected.




e.

If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of MIR-R on the sub bus

C360880C01
6.354,1.615 6.667,1.771 0.313,0.156 10 false *a
*a Background color is red - -


HINT:
·

A communication error in a sub bus does not affect the other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the bus 2 main bus lines are open, ECUs or sensors that are located farther away from the central gateway ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, HVB, R-MGC and ENG background color changes to red.)

C360881C01
6.344,5.896 6.656,6.094 0.313,0.198 10 false *f 0.75,5.969 1.063,6.167 0.313,0.198 10 false *f 0.417,2.667 0.875,2.865 0.458,0.198 10 false CGW 1.031,1.125 1.281,1.292 0.25,0.167 10 false *a 1.021,2.302 1.271,2.469 0.25,0.167 10 false *b 1.021,4.469 1.271,4.635 0.25,0.167 10 false *d 1.698,3.521 1.948,3.688 0.25,0.167 10 false *c 2.073,0.719 2.656,0.917 0.583,0.198 10 false F-MGC 1.927,1.292 2.76,1.49 0.833,0.198 10 false CAN J/C 1 1.854,1.885 2.188,2.083 0.333,0.198 10 false HV 2.458,1.865 2.875,2.031 0.417,0.167 10 false BRK 1.854,3.135 2.271,3.302 0.417,0.167 10 false MB 1.958,2.458 2.792,2.656 0.833,0.198 10 false CAN J/C 3 2.917,3.896 3.75,4.094 0.833,0.198 10 false CAN J/C 5 4.833,3.906 5.667,4.104 0.833,0.198 10 false CAN J/C 6 3.875,2.448 4.708,2.646 0.833,0.198 10 false CAN J/C 4 3.76,0.719 4.344,0.917 0.583,0.198 10 false HVB 4.313,0.719 4.896,0.917 0.583,0.198 10 false R-MGC 6.427,1.302 6.833,1.5 0.406,0.198 10 false ENG 3.875,1.281 4.708,1.479 0.833,0.198 10 false CAN J/C 2 3.74,3.073 4.167,3.25 0.427,0.177 10 false EPS 4.406,3.073 4.74,3.24 0.333,0.167 10 false STR 5.74,2.458 6.083,2.667 0.344,0.208 10 false SRS 6.469,3.896 6.75,4.083 0.281,0.188 10 false ST 5,4.531 5.5,4.781 0.5,0.25 10 false MIR-L 3.052,4.531 3.552,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 5.479,0.635 6.094,0.833 0.615,0.198 10 false : *e
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, MIR-L background color changes to red.)

C360882C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.708,3.552 2.021,3.708 0.313,0.156 10 false *c 1.021,4.458 1.333,4.615 0.313,0.156 10 false *d 5.5,0.625 5.896,0.792 0.396,0.167 10 false : *e 0.75,6.771 1.063,6.927 0.313,0.156 10 false *f 0.438,2.698 0.896,2.896 0.458,0.198 10 false CGW 2.063,0.74 2.646,0.99 0.583,0.25 10 false F-MGC 1.948,1.281 2.948,1.448 1,0.167 10 false CAN J/C 1 3.875,1.281 4.875,1.448 1,0.167 10 false CAN J/C 2 4.802,3.896 5.802,4.063 1,0.167 10 false CAN J/C 6 2.885,3.896 3.885,4.063 1,0.167 10 false CAN J/C 5 3.75,0.729 4.333,0.979 0.583,0.25 10 false HVB 4.323,0.74 4.906,0.99 0.583,0.25 10 false R-MGC 6.406,1.292 6.823,1.542 0.417,0.25 10 false ENG 5.74,2.458 6.156,2.708 0.417,0.25 10 false SRS 1.865,1.885 2.281,2.135 0.417,0.25 10 false HV 2.469,1.885 2.885,2.135 0.417,0.25 10 false BRK 1.958,2.458 2.958,2.625 1,0.167 10 false CAN J/C 3 3.875,2.448 4.875,2.615 1,0.167 10 false CAN J/C 4 1.854,3.146 2.188,3.396 0.333,0.25 10 false MB 3.75,3.073 4.167,3.323 0.417,0.25 10 false EPS 4.396,3.073 4.813,3.323 0.417,0.25 10 false STR 1.521,4.573 1.938,4.823 0.417,0.25 10 false DLC3 3.063,4.51 3.563,4.76 0.5,0.25 10 false MIR-R 4.969,4.51 5.469,4.76 0.5,0.25 10 false MIR-L 6.469,3.917 6.802,4.167 0.333,0.25 10 false ST
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Background color is red



h.

When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

C360883C01
0.604,0.198 0.917,0.354 0.313,0.156 10 false *a 0.625,1.938 0.938,2.094 0.313,0.156 10 false *b 0.719,1.031 1.031,1.188 0.313,0.156 10 false *c 0.719,1.448 1.031,1.604 0.313,0.156 10 false *d 6.354,1.281 6.667,1.438 0.313,0.156 10 false *d 6.344,0.948 6.656,1.104 0.313,0.156 10 false *c 6.354,2.99 6.667,3.146 0.313,0.156 10 false *d 0.698,3.146 1.01,3.302 0.313,0.156 10 false *d
*a When any of the following malfunctions occur on the bus 4 *b When any of the following malfunctions occur on a sub bus
*c Background color is red *d Not displayed


HINT:
·

When a malfunction occurs in the bus, almost all ECUs and sensors on the bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.




i.

If a communication error of all ECUs and sensors is indicated on the CAN Bus Check screen, a communication stop of the V bus (DLC3 - central gateway ECU) is suspected.

Open in both CAN branch lines in the V bus

C360884C01
1.031,1.146 1.344,1.302 0.313,0.156 10 false *a 1.031,2.313 1.344,2.469 0.313,0.156 10 false *b 1.698,3.531 2.01,3.688 0.313,0.156 10 false *c 1.021,4.385 1.333,4.542 0.313,0.156 10 false *d 5.5,0.635 6,0.875 0.5,0.24 10 false : *e 0.719,6.219 0.969,6.385 0.25,0.167 10 false *f 6.385,6.135 6.635,6.302 0.25,0.167 10 false *f 0.448,2.667 0.948,2.833 0.5,0.167 10 false CGW 2.063,0.719 2.646,0.885 0.583,0.167 10 false F-MGC 1.948,1.302 2.865,1.469 0.917,0.167 10 false CAN J/C 1 3.844,1.292 4.76,1.458 0.917,0.167 10 false CAN J/C 2 1.927,2.469 2.844,2.635 0.917,0.167 10 false CAN J/C 3 3.833,2.479 4.75,2.646 0.917,0.167 10 false CAN J/C 4 2.917,3.906 3.833,4.073 0.917,0.167 10 false CAN J/C 5 4.813,3.906 5.729,4.073 0.917,0.167 10 false CAN J/C 6 3.75,0.719 4.167,0.885 0.417,0.167 10 false HVB 4.313,0.729 4.979,0.896 0.667,0.167 10 false R-MGC 6.417,1.313 6.917,1.563 0.5,0.25 10 false ENG 5.729,2.479 6.229,2.729 0.5,0.25 10 false SRS 6.469,3.917 6.969,4.167 0.5,0.25 10 false ST 4.99,4.51 5.49,4.76 0.5,0.25 10 false MIR-L 3.063,4.531 3.563,4.781 0.5,0.25 10 false MIR-R 1.521,4.573 2.021,4.823 0.5,0.25 10 false DLC3 1.854,3.146 2.354,3.396 0.5,0.25 10 false MB 3.75,3.094 4.083,3.344 0.333,0.25 10 false EPS 4.385,3.094 4.719,3.344 0.333,0.25 10 false STR 1.865,1.906 2.198,2.156 0.333,0.25 10 false HV 2.469,1.896 2.885,2.146 0.417,0.25 10 false BRK
*a Bus 2 *b Bus 4
*c Sub Bus *d V Bus
*e Location of Malfunction *f Not displayed


HINT:

When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.




HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


a.

If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

HINT:

Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.


i.

If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

C240699C05
6.979,0.323 7.146,0.583 0.167,0.26 10 false *a
*a Items to be checked - -


NOTICE:
·

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

·

Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)



HINT:

As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



ii.

If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

C240700C05
6.969,0.292 7.135,0.604 0.167,0.313 10 false *a
*a Items to be checked - -


NOTICE:

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.


HINT:
·

If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.

·

When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.





b.

To help determine the part of the non-bus 2 that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

C240701C04
1.229,4.5 1.656,4.76 0.427,0.26 10 *a 4.948,0.333 5.26,0.604 0.313,0.271 10 *d 3.677,0.917 4.156,1.396 0.479,0.479 10 *c 3.906,0.281 4.427,0.76 0.521,0.479 10 *f 0.688,2.333 1.323,2.667 0.635,0.333 10 *e 0.417,1.635 0.896,2.063 0.479,0.427 10 *b 0.917,2.729 2.156,3.104 1.24,0.375 10 Output from 2.448,2.74 3.698,3.198 1.25,0.458 10 Output DTC 4.708,2.74 6.198,3.323 1.49,0.583 10 Tester display
*a Items to be checked *b ECM
*c Gateway function equipped ECU *d Location of malfunction
*e Bus *f Sub Bus


NOTICE:

This DTC table is from another model, and is only used here to show the ECUs connected to a bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.


HINT:
·

As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub bus, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.

·

When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.




c.

When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

·

Short between CAN lines (CANH and CANL)

·

Short between a CAN line (CANH or CANL) and ground

·

Short between a CAN line (CANH or CANL) and +B

·

Open in a CAN branch line (CANH or CANL) of an ECU or sensor

·

Open in a CAN main line (CANH or CANL) between 2 ECUs that have a terminating resistor




CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.

HINT:

The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.


ECU/Sensor Name GTS Display Installed on
Central gateway ECU CAN Gateway All vehicles
ECM ECM (Engine) All vehicles
Power steering ECU assembly Power Steering (EPS) All vehicles
Air conditioning amplifier assembly Air Conditioning Amplifier All vehicles
Airbag sensor assembly Airbag All vehicles
Spiral with sensor cable sub-assembly (steering angle sensor) Spiral cable (Steering Angle Sensor) All vehicles
Certification ECU (smart key ECU assembly) Certification (Smart) Vehicles with an entry and start system
4WD ECU assembly Four Wheel Drive Control Vehicles with 4WD/AWD
Brake actuator assembly (skid control ECU) Skid Control (ABS/VSC/TRAC) All vehicles
Main body ECU (multiplex network body ECU) Main Body All vehicles
Engine stop and start ECU Stop and Go/Start Vehicles with a stop and start system
Combination meter assembly Combination Meter All vehicles
Radio and display receiver assembly Display and Navigation (AVN1) Vehicles with an audio and visual system (for radio and display type)
Parking assist ECU Parking Assist Monitor System Vehicles with a panoramic view monitor system
Driving support ECU assembly Driving Support (Cruise Control-ACC) Vehicles with a pre-crash safety system
Clearance warning ECU assembly Clearance Warning (Clearance Sonar) Vehicles with a TOYOTA parking assist-sensor system (for 8 sensor type)
Forward recognition camera Front Camera Module Vehicles with a pre-crash safety system
Blind spot monitor sensor LH Blind Spot Monitor Master Vehicles with a blind spot monitor system
Millimeter wave radar sensor assembly Front Radar Vehicles with a pre-crash safety system
Television camera assembly Parking Assist Monitor System Vehicles with a parking assist monitor system (for camera built-in ECU)
Multiplex network door ECU Back Door Vehicles with a power back door system
Position control ECU and switch assembly D-Seat Vehicles with a seat memory
Telematics transceiver DCM Vehicles with a telematics transceiver



DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

ECM

HINT:

DTC communication uses the CAN communication system.


i.

GTS Display "Engine" (for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF)

Powertrain > Engine > Trouble Codes
50001 61
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U1103 Manufacture Control U11 Lost Communication The following condition occurs 10 times consecutively: The ECM is unable to receive certain data from the engine stop and start ECU for 2.1 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The ECM power supply voltage is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 60 seconds. - The DTC remains stored until it is cleared using the GTS.


ii.

GTS Display "Engine and ECT" (for 2AR-FE, 3ZR-FAE, 3ZR-FE, 2WW)

Powertrain > Engine and ECT > Trouble Codes
50001 234
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0129 Lost Communication With Brake System Control Module The following condition occurs 10 times consecutively: The ECM is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2.1 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The ECM power supply voltage is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 60 seconds. - The DTC remains stored until it is cleared using the GTS.
U1103 Manufacture Control U11 Lost Communication The following condition occurs 10 times consecutively: The ECM is unable to receive certain data from the engine stop and start ECU for 2.1 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The ECM power supply voltage is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 60 seconds. - The DTC remains stored until it is cleared using the GTS.


iii.

GTS Display "Cruise Control" (w/ Cruise Control System)

Powertrain > Cruise Control > Trouble Codes
50001 76
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0122 Lost Communication with Vehicle Dynamics Control Module The ECM does not receive data from the brake actuator assembly (skid control ECU) for 2.6 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The ECM power supply voltage is 10.5 V or higher.


Turn the ignition switch to ON and wait at least 2.6 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.


iv.

GTS Display "Radar Cruise1" (w/ Dynamic Radar Cruise Control System)

Powertrain > Radar Cruise1 > Trouble Codes
50001 74
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The skid control ECU (brake actuator assembly) is unable to receive certain data from the ECM for 1 second or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module The ECM does not receive data from the brake actuator assembly (skid control ECU) for 2.6 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 2.6 seconds or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U1104 Lost Communication with Distance Control Module The driving support ECU assembly data sent to the ECM, brake actuator assembly (skid control ECU) or millimeter wave radar sensor assembly is lost for 0.92 seconds or more. Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The radar cruise control system (vehicle control mode) is operating.


Allow the radar cruise control system (vehicle control mode) to operate for 0.92 second or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.



b.

BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) / GTS Display "ABS/VSC/TRC"

HINT:

DTC communication uses the CAN communication system.


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus Off Either condition is met:
·

The response sent to the brake actuator assembly (skid control ECU) from the spiral with sensor cable sub-assembly (steering angle sensor) is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly (skid control ECU) from the spiral with sensor cable sub-assembly (steering angle sensor) is invalid at least once within 5 seconds.

·

The brake actuator assembly (skid control ECU) cannot send or receive data (the bus is off) 10 times consecutively.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication With ECM/PCM "A" The brake actuator assembly (skid control ECU) is unable to receive certain data from the ECM for 2 seconds or more. All conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The vehicle speed is 15 km/h (9 mph) or more.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0124 Lost Communication With Lateral Acceleration Sensor Module Either condition is met:
·

The brake actuator assembly (skid control ECU) is unable to receive certain data from the airbag sensor assembly for 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the airbag sensor assembly at least once within 5 seconds.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

ABS indicator light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication With Steering Angle Sensor Module Either condition is met:
·

The brake actuator assembly (skid control ECU) is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 1 second or more.

·

The following condition occurs 10 times or more consecutively within 60 seconds: The brake actuator assembly (skid control ECU) is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) at least once within 5 seconds.


Both conditions are met:
·

1 second or more elapses after turning the ignition switch to ON.

·

The brake actuator assembly (skid control ECU) power supply voltage is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 60 seconds. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.


c.

AIR CONDITIONING AMPLIFIER ASSEMBLY / GTS Display "Air Conditioner"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Air Conditioner > Trouble Codes
50001 121
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication With ECM/PCM "A" The air conditioning amplifier assembly is unable to receive certain data from the ECM for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The air conditioning amplifier assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.
U0131 Lost Communication With Power Steering Control Module The air conditioning amplifier assembly is unable to receive certain data from the power steering ECU assembly for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The air conditioning amplifier assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication With Body Control Module "B" The air conditioning amplifier assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The air conditioning amplifier assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module The air conditioning amplifier assembly is unable to receive certain data from the combination meter assembly for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The air conditioning amplifier assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.


d.

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) / GTS Display "Main Body"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Main Body > Trouble Codes
50001 123
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication With ECM/PCM "A" The main body ECU (multiplex network body ECU) is unable to receive certain data from the ECM for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0101 Lost Communication with TCM The main body ECU (multiplex network body ECU) is unable to receive certain data from the ECM for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0120 Lost Communication With Starter / Generator Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the certification ECU (smart key ECU assembly) for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the brake actuator assembly (skid control ECU) for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the airbag sensor assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the combination meter assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the air conditioning amplifier assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0182 Lost Communication with AFS The main body ECU (multiplex network body ECU) is unable to receive certain data from the forward recognition camera for 10 seconds or more. Both conditions are met:
·

5 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 15 seconds. - The DTC remains stored until it is cleared using the GTS.
U0208 Lost Communication with "Seat Control Module A" The main body ECU (multiplex network body ECU) is unable to receive certain data from the position control ECU and switch assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0230 Lost Communication with Rear Gate Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the multiplex network door ECU for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U023A Lost Communication With Image Processing Module "A" The main body ECU (multiplex network body ECU) is unable to receive certain data from the forward recognition camera for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0265 Lost Communication with Parking Assist Monitor Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the television camera assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U0327 Software Incompatibility with Vehicle Security Control Module The main body ECU (multiplex network body ECU) is unable to receive certain data from the certification ECU (smart key ECU assembly) for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.
U1002 Lost Communication with Gateway Module The main body ECU (multiplex network body ECU) detects a problem when communicating with the multiplex network door ECU, position control ECU and switch assembly. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The main body ECU (multiplex network body ECU) power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.


e.

POWER STEERING ECU ASSEMBLY / GTS Display "EMPS"

HINT:

DTC communication uses the CAN communication system.


Chassis > EMPS > Trouble Codes
50001 142
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The power steering ECU assembly is unable to receive certain data from the ECM for 5 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The power steering ECU assembly power supply voltage is 9.5 V or higher.


Drive the vehicle for 6 seconds at a speed of 20 km/h (12 mph) or more. - The DTC is stored only while the malfunction is present.
U0129 Lost Communication with Brake System Control Module The power steering ECU assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2.3 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The power steering ECU assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4.3 seconds. The EPS warning light illuminates. The DTC is stored only while the malfunction is present.


f.

COMBINATION METER ASSEMBLY / GTS Display "Combination Meter"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Combination Meter > Trouble Codes
50001 122
DTC No. Detection Item DTC Detection Condition DTC Check Procedure DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The combination meter assembly is unable to receive certain data from the ECM for 2 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 2 seconds. - The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module Either condition is met:
·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2 seconds or more.

·

The combination meter assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 3 seconds or more.


Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 3 seconds. - The DTC remains stored until it is cleared using the GTS.
U0131 Lost Communication with Power Steering Control Module The combination meter assembly is unable to receive certain data from the power steering ECU assembly for 3 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 3 seconds. The EPS warning light illuminates. The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The combination meter assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 3 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 3 seconds. - The DTC remains stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The combination meter assembly is unable to receive certain data from the airbag sensor assembly for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 10 seconds. The SRS warning light illuminates. The DTC remains stored until it is cleared using the GTS.
U0163 Lost Communication With Navigation Control Module The combination meter assembly is unable to receive certain data from the radio and display receiver assembly for 3 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 3 seconds. - The DTC remains stored until it is cleared using the GTS.
U023A Lost Communication with Front Camera Module The combination meter assembly is unable to receive certain data from the forward recognition camera for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U1104 Lost Communication with Driving Support ECU The combination meter assembly is unable to receive certain data from the driving support ECU assembly for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.


g.

RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type]) / GTS Display "Navigation System"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Navigation System > Trouble Codes
50001 212
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method

ECB*: Electronically Controlled Brake System

U0073 Sending Malfunction (Navigation to APGS) The radio and display receiver assembly is unable to send or receive data 5 seconds consecutively. - Turn the ignition switch to ON and wait at least 1 second. - The DTC remains stored until it is cleared using the GTS.
U0100 Engine ECU Communication One of the following conditions is met:
·

The radio and display receiver assembly is unable to receive certain data from the ECM for 1.24 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the ECM for 2 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the ECM for 2.5 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the ECM for 4 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the ECM for 10 seconds or more.


Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 11 seconds. - The DTC remains stored until it is cleared using the GTS.
U0126 Steering Sensor Communication Either condition is met:
·

The radio and display receiver assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 0.72 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 10.8 seconds or more.


Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 11.8 seconds. - The DTC remains stored until it is cleared using the GTS.
U0129 VSC(ECB*)ECU Communication Either condition is met:
·

The radio and display receiver assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 1 second or more.

·

The radio and display receiver assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 4 second or more.


Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.
U0131 Lost Communication with Electric Power Steering ECU The radio and display receiver assembly is unable to receive certain data from the power steering ECU assembly for 1 second or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The radio and display receiver assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 3 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 4 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Meter ECU Communication The radio and display receiver assembly is unable to receive certain data from the combination meter assembly for 30 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 31 seconds. - The DTC remains stored until it is cleared using the GTS.
U0164 Air Conditioner ECU Communication One of the following conditions is met:
·

The radio and display receiver assembly is unable to receive certain data from the air conditioning amplifier assembly for 3 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the air conditioning amplifier assembly for 6 seconds or more.

·

The radio and display receiver assembly is unable to receive certain data from the air conditioning amplifier assembly for 15 seconds or more.


Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 16 seconds. - The DTC remains stored until it is cleared using the GTS.
U0182 Lost Communication with Lighting Control Module Front The radio and display receiver assembly is unable to receive certain data from the forward recognition camera for 1 second or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. - The DTC remains stored until it is cleared using the GTS.
U1110 Clearance Sonar ECU Communication The radio and display receiver assembly is unable to receive certain data from the clearance warning ECU assembly for 10 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The radio and display receiver assembly power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 11 seconds. - The DTC remains stored until it is cleared using the GTS.


h.

4WD ECU ASSEMBLY (for 4WD/AWD) / GTS Display "Four Wheel Drive"

HINT:

DTC communication uses the CAN communication system.


Chassis > Four Wheel Drive > Trouble Codes
50001 118
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus Off The 4WD ECU assembly is unable to send or receive data 10 times consecutively. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The 4WD ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 60 seconds. The "Check 4WD System" message is displayed. The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication With ECM/PCM "A" Either condition is met:
·

The 4WD ECU assembly is unable to receive certain data from the ECM for 2 seconds or more.

·

The 4WD ECU assembly is unable to receive certain data from the ECM for 3.5 seconds or more.


Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The 4WD ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 4.5 seconds or more at a speed of 60 km/h (37 mph) or more. The "Check 4WD System" message is displayed. The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication With Steering Angle Sensor Module The 4WD ECU assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 1 second or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The 4WD ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds. The "Check 4WD System" message is displayed. The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication With Brake System Control Module Either condition is met:
·

The 4WD ECU assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 3 seconds or more.

·

The 4WD ECU assembly is unable to receive certain data from the brake actuator assembly (skid control ECU) for 8 seconds or more.


Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The 4WD ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. The "Check 4WD System" message is displayed. The DTC remains stored until it is cleared using the GTS.


i.

CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)

HINT:

DTC communication uses the CAN communication system.


i.

GTS Display "Entry&Start"

Body Electrical > Entry&Start > Trouble Codes
50001 125
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication With ECM/PCM "A" The certification ECU (smart key ECU assembly) is unable to receive certain data from the ECM for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The certification ECU (smart key ECU assembly) power supply voltage is 10 V or higher.


Wait 20 seconds after turning the ignition switch ACC or ON. - The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The certification ECU (smart key ECU assembly) is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The certification ECU (smart key ECU assembly) power supply voltage is 10 V or higher.


Wait 20 seconds after turning the ignition switch ACC or ON. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The certification ECU (smart key ECU assembly) is unable to receive certain data from the combination meter assembly for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The certification ECU (smart key ECU assembly) power supply voltage is 10 V or higher.


Wait 20 seconds after turning the ignition switch ACC or ON. - The DTC remains stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module The certification ECU (smart key ECU assembly) is unable to receive certain data from the engine stop and start ECU for 10 seconds or more. Both conditions are met:
·

10 seconds or more elapse after a power source mode change is detected (+B changes from off to on, ACC changes between on and off, or IG changes between on and off).

·

The certification ECU (smart key ECU assembly) power supply voltage is 10 V or higher.


Wait 20 seconds after turning the ignition switch ACC or ON. - The DTC remains stored until it is cleared using the GTS.


ii.

GTS Display "Power Source Control"

Body Electrical > Power Source Control > Trouble Codes
50001 223
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 ECM Communication The certification ECU (smart key ECU assembly) is unable to receive certain data from the ECM for 3.1 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The certification ECU (smart key ECU assembly) power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3.1 seconds. - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The certification ECU (smart key ECU assembly) is unable to receive certain data from the main body ECU (multiplex network body ECU) for 3 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The certification ECU (smart key ECU assembly) power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The certification ECU (smart key ECU assembly) is unable to receive certain data from the combination meter assembly for 3.1 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The certification ECU (smart key ECU assembly) power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 3.1 seconds. - The DTC remains stored until it is cleared using the GTS.
U1103 Lost Communication with Stop and Start Control Module The certification ECU (smart key ECU assembly) is unable to receive certain data from the engine stop and start ECU for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The certification ECU (smart key ECU assembly) power supply voltage is 9.5 V or higher.


Turn the ignition switch to ON and wait at least 5 seconds. - The DTC remains stored until it is cleared using the GTS.


iii.

GTS Display "Starting Control"

Body Electrical > Starting Control > Trouble Codes
50001 221
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication With ECM/PCM "A" The certification ECU (smart key ECU assembly) is unable to receive certain data from the ECM for 2 seconds or more. The ignition switch is ON. Turn the ignition switch to ON and wait at least 2 seconds. - The DTC remains stored until it is cleared using the GTS.



j.

BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System) / GTS Display "Blind Spot Monitor Master"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method

*: Refer to the Blind Spot Monitor System.

Click here(Click here)

U0100 Lost Communication with ECM/PCM "A" The blind spot monitor sensor LH is unable to receive certain data from the ECM for 10.8 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch to ON.

·

The vehicle speed is 5 km/h (3 mph) or more.

·

The blind spot monitor main switch is on.

·

The blind spot monitor sensor LH power supply voltage is 10 V or higher.


Drive the vehicle for 11.8 seconds at a speed of 5 km/h (3 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module Either condition is met:
·

The blind spot monitor sensor LH is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 0.72 seconds or more.

·

The blind spot monitor sensor LH is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 10.7 seconds or more.


All conditions are met:
·

1 second elapses after turning the ignition switch to ON.

·

The blind spot monitor main switch is on.

·

The blind spot monitor sensor LH power supply voltage is 10 V or higher.


Turn the ignition switch to ON and turn the blind spot monitor main switch on, and then wait 11.7 seconds or more. Displays messages on the multi-information display. The DTC is stored only while the malfunction is present.
U0129 Lost Communication with Brake System Control Module The blind spot monitor sensor LH is unable to receive certain data from the brake actuator assembly (skid control ECU) for 22.6 seconds or more. All conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The blind spot monitor main switch is on.

·

The blind spot monitor sensor LH power supply voltage is 10 V or higher.


Turn the ignition switch to ON and turn the blind spot monitor main switch on, and then wait 24.6 seconds or more. Displays messages on the multi-information display. The DTC is stored only while the malfunction is present.
U0142 Lost Communication with Body Control Module "B" The blind spot monitor sensor LH is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch to ON.

·

The blind spot monitor main switch is on.

·

The blind spot monitor sensor LH power supply voltage is 10 V or higher.


Turn the ignition switch to ON and turn the blind spot monitor main switch on, and then wait 11.6 seconds or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0232* Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor LH is unable to receive information from the blind spot monitor sensor RH for 7.6 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch to ON.

·

The blind spot monitor main switch is on.

·

The blind spot monitor sensor LH power supply voltage is 10 V or higher.


Turn the ignition switch to ON and turn the blind spot monitor main switch on, and then wait 8.6 seconds or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.


k.

DRIVING SUPPORT ECU ASSEMBLY

HINT:

DTC communication uses the CAN communication system.


i.

GTS Display "Radar Cruise2" (w/ Dynamic Radar Cruise Control System)

Powertrain > Radar Cruise2 > Trouble Codes
50001 197
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The driving support ECU assembly is unable to receive certain data from the ECM for 0.92 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch to ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 1.92 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0125 Lost Communication with Yaw Rate Sensor Module The driving support ECU assembly is unable to receive certain data from the airbag sensor assembly for 0.72 seconds or more. All conditions are met:
·

3 seconds elapse after turning the ignition switch is ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 3.72 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module The driving support ECU assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 5.04 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch is ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 6.04 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The driving support ECU assembly is unable to receive certain data from the brake booster with master cylinder assembly (skid control ECU) for 1.08 seconds or more. All conditions are met:
·

2 seconds elapse after turning the ignition switch is ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 3.08 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0235 Lost Communication with Cruise Control Front Distance Range Sensor The driving support ECU assembly is unable to receive certain data from the millimeter wave radar sensor assembly for 1.6 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch is ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 2.6 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U1104 Lost Communication with Driving Support ECU The driving support ECU assembly is unable to receive certain data from the millimeter wave radar sensor assembly for 0.144 seconds or more. All conditions are met:
·

1 second elapses after turning the ignition switch is ON.

·

The vehicle speed is 36 km/h (22 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle for 1.144 seconds or more at a speed of 36 km/h (22 mph) or more. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.


ii.

GTS Display "Pre-Crash2" (w/ Pre-crash Safety System)

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM The driving support ECU assembly does not receive data from the ECM for 3.07 seconds or more. All conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

Vehicle speed is 5 km/h (3 mph) or more.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Drive the vehicle at a speed of 5 km/h (3 mph) or more for 6 seconds or more.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0125 Lost Communication with Yaw Rate Sensor Module The driving support ECU assembly is unable to receive certain data from the airbag sensor assembly for 0.036 seconds or more. Both conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0126 Lost Communication with Steering Angle Sensor Module The driving support ECU assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 3.02 seconds or more. Both conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0129 Lost Communication with Brake System Control Module The driving support ECU assembly is unable to receive certain data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more. Both conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0235 Lost Communication with Cruise Control Front Distance Range Sensor The driving support ECU assembly is unable to receive certain data from the millimeter wave radar sensor assembly for 0.3 seconds or more. Both conditions are met:
·

3 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 3 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U023A Lost Communication with Image Processing Module "A" The driving support ECU assembly is unable to receive certain data from the forward recognition camera for 3 seconds or more. Both conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U1002 Lost Communication with Gateway Module The driving support ECU assembly detects a problem when communicating with the millimeter wave radar sensor assembly and forward recognition camera. Both conditions are met:
·

6 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 6 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U1104 Lost Communication with Driving Support ECU The driving support ECU assembly data sent to each ECU (sensor) is lost for 3 seconds or more. All conditions are met:
·

2 seconds elapse after turning the ignition switch is ON.

·

The driving support ECU assembly power supply voltage is 10 V or higher.


Turn the ignition switch to ON and wait at least 2 seconds.
·

The PCS indicator blinks.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.



l.

FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)

HINT:

DTC communication uses the CAN communication system.


i.

GTS Display "LKA/LDA" (w/ Lane Departure Warning System)

Chassis > LKA/LDA > Trouble Codes
50001 355
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The forward recognition camera is unable to receive certain data from the ECM for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0101 Lost Communication with TCM The forward recognition camera is unable to receive certain data from the ECM for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0123 Lost Communication with Yaw Rate Sensor Module The forward recognition camera is unable to receive certain data from the airbag sensor assembly for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0126 Lost Communication with Steering Angle Sensor Module The forward recognition camera is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0129 Lost Communication with Brake System Control Module The forward recognition camera is unable to receive certain data from the brake actuator assembly (skid control ECU) for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0131 Lost Communication with Power Steering Control Module The forward recognition camera is unable to receive certain data from the power steering ECU assembly for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0142 Lost Communication with Body Control Module "B" The forward recognition camera is unable to receive certain data from the main body ECU (multiplex network body ECU) for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) The forward recognition camera is unable to receive certain data from the combination meter assembly for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 60 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0235 Lost Communication with Cruise Control Front Distance Range Sensor The forward recognition camera is unable to receive certain data from the millimeter wave radar sensor assembly for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U023A Lost Communication with Image Processing Module "A" The forward recognition camera is unable to receive certain data from the forward recognition camera for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U1104 Lost Communication with Driving Support ECU The forward recognition camera is unable to receive certain data from the millimeter wave radar sensor assembly for 5 seconds or more. All conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The lane departure alert main switch is on.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.


ii.

GTS Display "Front Recognition Camera" (w/ Forward Recognition Camera System)

Chassis > Front Recognition Camera > Trouble Codes
50001 386
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The forward recognition camera data sent to the ECM is lost for 5 seconds or more. All conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0101 Lost Communication with TCM The forward recognition camera data sent to the ECM is lost for 5 seconds or more. All conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0123 Lost Communication with Yaw Rate Sensor Module The forward recognition camera data sent to the airbag sensor assembly is lost for 5 seconds or more. All conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The vehicle speed is 1 km/h (1 mph) or more.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Drive the vehicle for 7 seconds at a speed of 1 km/h (1 mph) or more.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0129 Lost Communication with Brake System Control Module The forward recognition camera data sent to the brake actuator assembly (skid control ECU) is lost for 5 seconds or more. Both conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0142 Lost Communication with Body Control Module "B" The forward recognition camera data sent to the main body ECU (multiplex network body ECU) is lost for 5 seconds or more. Both conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U0235 Lost Communication with Cruise Control Front Distance Range Sensor The forward recognition camera data sent to the millimeter wave radar sensor assembly is lost for 5 seconds or more. Both conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.
U1104 Lost Communication with Driving Support ECU The forward recognition camera data sent to the driving support ECU assembly is lost for 5 seconds or more. Both conditions are met:
·

2 seconds elapses after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 16 V.


Turn the ignition switch to ON and wait at least 7 seconds.
·

The LDA indicator illuminates.

·

Displays messages on the multi-information display.


The DTC is stored only while the malfunction is present.


iii.

GTS Display "Road Sign Assist" (w/ Road Sign Assist System)

Body Electrical > Road Sign Assist > Trouble Codes
50001 387
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The forward recognition camera is unable to receive certain data from the ECM for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0101 Lost Communication with TCM The forward recognition camera is unable to receive certain data from the ECM for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0123 Lost Communication with Yaw Rate Sensor Module The forward recognition camera is unable to receive certain data from the airbag sensor assembly for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The forward recognition camera is unable to receive certain data from the brake actuator assembly (skid control ECU) for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The forward recognition camera is unable to receive certain data from the main body ECU (multiplex network body ECU) for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) The forward recognition camera is unable to receive certain data from the combination meter assembly for 5 seconds or more. Both conditions are met:
·

2 seconds or more elapse after turning the ignition switch to ON.

·

The forward recognition camera power supply voltage is 8 to 10 V.


Turn the ignition switch to ON and wait at least 7 seconds. Displays messages on the multi-information display. The DTC remains stored until it is cleared using the GTS.



m.

TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System [for Camera built-in ECU]) / GTS Display "IPA/Parking Assist Monitor"

Chassis > IPA/Parking Assist Monitor > Trouble Codes
50001 85
HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method

*: Refer to Parking Assist Monitor System (for Camera built-in ECU).

Click here(Click here)

U0126 Lost Communication with Steering Angle Sensor Module The television camera assembly is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 11 seconds or more. 3 seconds or more elapse after turning the ignition switch to ON. Turn the ignition switch to ON and wait at least 14 seconds. - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The television camera assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 11 seconds or more. 3 seconds or more elapse after turning the ignition switch to ACC. Turn the ignition switch to ACC and wait at least 14 seconds. - The DTC remains stored until it is cleared using the GTS.
U0163 Lost Communication with Navigation Control Module The television camera assembly is unable to receive certain data from the radio and display receiver assembly for 11 seconds or more. 3 seconds or more elapse after turning the ignition switch to ACC. Turn the ignition switch to ACC and wait at least 14 seconds. - The DTC remains stored until it is cleared using the GTS.
U1000* CAN Communication Failure (Message Registry) When the ignition switch is turned to ON, a CAN communication malfunction is detected. The ignition switch to ON. Turn the ignition switch to ON. - The DTC remains stored until it is cleared using the GTS.
U1110 Lost Communication with Intuitive Parking Assist Module The television camera assembly is unable to receive certain data from the clearance warning ECU assembly for 11 seconds or more. 3 seconds or more elapse after turning the ignition switch to ON. Turn the ignition switch to ON and wait at least 14 seconds. - The DTC remains stored until it is cleared using the GTS.


n.

CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type]) / GTS Display "Clearance Sonar"

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The clearance warning ECU assembly is unable to receive certain data from the ECM for 3.5 seconds or more. Both conditions are met:
·

5 seconds elapses after turning the ignition switch to ON.

·

The clearance warning ECU assembly power supply voltage is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 8.5 seconds. - The DTC remains stored until it is cleared using the GTS.
U0101 Lost Communication with TCM The clearance warning ECU assembly is unable to receive certain data from the ECM for 5 seconds or more. Both conditions are met:
·

5 seconds elapses after turning the ignition switch to ON.

·

The clearance warning ECU assembly power supply voltage is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" Either condition is met:
·

The clearance warning ECU assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 4 seconds or more.

·

The clearance warning ECU assembly is unable to receive certain data from the main body ECU (multiplex network body ECU) for 5 seconds or more.


Both conditions are met:
·

5 seconds elapses after turning the ignition switch to ON.

·

The clearance warning ECU assembly power supply voltage is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module Either condition is met:
·

The clearance warning ECU assembly is unable to receive certain data from the combination meter assembly for 3 seconds or more.

·

The clearance warning ECU assembly is unable to receive certain data from the combination meter assembly for 5 seconds or more.


Both conditions are met:
·

5 seconds elapses after turning the ignition switch to ON.

·

The clearance warning ECU assembly power supply voltage is 10.2 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.


o.

PARKING ASSIST ECU (w/ Panoramic View Monitor System) / GTS Display "Panoramic View Monitor"

HINT:

DTC communication uses the CAN communication system.


Chassis > Panoramic View Monitor > Trouble Codes
50001 353
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus Off The parking assist ECU is unable to send or receive data for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication with ECM/PCM "A" The parking assist ECU is unable to receive certain data from the ECM for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module The parking assist ECU is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.
U0129 Lost Communication with Brake System Control Module The parking assist ECU is unable to receive certain data from the brake actuator assembly (skid control ECU) for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The parking assist ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.
U1110 Lost Communication with Clearance Sonar Module The parking assist ECU is unable to receive certain data from the clearance warning ECU assembly for 10 seconds or more. Both conditions are met:
·

3 seconds elapses after turning the ignition switch to ON.

·

The parking assist ECU power supply voltage is 7.5 V or higher.


Turn the ignition switch to ON and wait at least 13 seconds. - The DTC remains stored until it is cleared using the GTS.


p.

MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System) / GTS Display "Back Door"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Back Door > Trouble Codes
50001 159
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0101 Lost Communication with TCM The multiplex network door ECU is unable to receive certain data from the ECM for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0122 Lost Communication with Vehicle Dynamics Control Module The multiplex network door ECU is unable to receive certain data from the brake actuator assembly (skid control ECU) for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0142 Lost Communication with Body Control Module "B" The multiplex network door ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The multiplex network door ECU is unable to receive certain data from the combination meter assembly for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U0327 Lost Communication with Vehicle Security Control Module The multiplex network door ECU is unable to receive certain data from the certification ECU (smart key ECU assembly) for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.
U1117 Lost Communication with Accessory Gateway The multiplex network door ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The multiplex network door ECU power supply voltage is 10.8 V or higher.


Turn the ignition switch to ON and wait at least 10 seconds. - The DTC remains stored until it is cleared using the GTS.


q.

ENGINE STOP AND START ECU (w/ Stop and Start System) / GTS Display "Stop and Start"

HINT:

DTC communication uses the CAN communication system.


Powertrain > Stop and Start > Trouble Codes
50001 227
DTC No. Detection Item DTC Detection Condition DTC Detection Precondition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The engine stop and start ECU is unable to receive certain data from the ECM for 0.76 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 1.76 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0121 Lost Communication with Brake System Control Module The engine stop and start ECU is unable to receive certain data from the brake actuator assembly (skid control ECU) for 2.22 seconds or more. Both conditions are met:
·

2.1 seconds or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 4.32 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication with Steering Angle Sensor Module The engine stop and start ECU is unable to receive certain data from the spiral with sensor cable sub-assembly (steering angle sensor) for 0.72 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 1.72 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0131 Lost Communication with Electric Power Steering ECU The engine stop and start ECU is unable to receive certain data from the power steering ECU assembly for 0.8 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 1.8 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0140 Lost Communication with Body Control Module The engine stop and start ECU is unable to receive certain data from the main body ECU (multiplex network body ECU) for 3.6 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 4.6 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0151 Lost Communication with Restraints Control Module The engine stop and start ECU is unable to receive certain data from the airbag sensor assembly for 10.6 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 11.6 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module The engine stop and start ECU is unable to receive certain data from the combination meter assembly for 10.6 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 11.6 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0164 Lost Communication with HVAC Control Module The engine stop and start ECU is unable to receive certain data from the air conditioning amplifier assembly for 10.6 seconds or more. Both conditions are met:
·

1 second or more elapse after turning the ignition switch to ON.

·

The engine stop and start ECU power supply voltage is 10.5 V or higher


Turn the ignition switch to ON and wait at least 11.6 seconds. Stop and start indicator light illuminates. The DTC remains stored until it is cleared using the GTS.


r.

TELEMATICS TRANSCEIVER (w/ Telematics Transceiver) / GTS Display "Telematics"

HINT:

DTC communication uses the CAN communication system.


Body Electrical > Telematics > Trouble Codes
50001 233
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM/PCM "A" The telematics transceiver is unable to receive certain data from the ECM for 4.5 seconds or more. 10 seconds or more elapse after turning the ignition switch to ON. Turn the ignition switch to ON and wait at least 20 seconds. - The DTC remains stored until it is cleared using the GTS.


s.

CENTRAL GATEWAY ECU

HINT:

The central gateway ECU is connected to the CAN communication system but CAN communication DTCs are not stored.



t.

AIRBAG SENSOR ASSEMBLY

HINT:

The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.



u.

SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

HINT:

The spiral with sensor cable sub-assembly (steering angle sensor) is connected to the CAN communication system but CAN communication DTCs are not stored.



v.

MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)

HINT:

The millimeter wave radar sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.



w.

POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Memory)

HINT:

The position control ECU and switch assembly is connected to the CAN communication system but CAN communication DTCs are not stored.



x.

Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.



DTC COMBINATION TABLE (OPEN OR SHORT IN BUS 2, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU and sensor connected to the bus 2 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN bus line(s) and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN bus line(s) does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a short to ground or +B in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 8 to 16) first.

·

If an open occurs in just one of the lines of a CAN bus line(s), DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.

·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode
(Click here)
Air Conditioning Amplifier Communication Stop Mode
(Click here)
Main Body ECU Communication Stop Mode
(Click here)
Central Gateway ECU
Bus 2 Airbag Sensor Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 - ○ - -
U0131 - ○ - -
U0142 - ○ ○ -
U0155 - ○ - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - ○ -
U0101 - - ○ -
U0120 - - ○ -
U0129 - - ○ -
U0151 ○ - ○ -
U0155 - - ○ -
U0164 - ○ ○ -
U0182 - - ○ -
U023A - - ○ ○
U0265 - - ○ ○
U0327 - - ○ -
Central Gateway ECU - - - - -
Engine Stop and Start ECU U0100 - - - -
U0121 - - - -
U0126 - - - -
U0131 - - - -
U0140 - - ○ -
U0151 ○ - - -
U0155 - - - -
U0164 - ○ - -
ECM U0122 - - - -
U0129 - - - -
U1103 - - - -
U1104 - - - ○
Power Steering ECU Assembly U0100 - - - -
U0129 - - - -
4WD ECU Assembly* U0100 - - - -
U0126 - - - -
U0129 - - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - - -
U0140 - - ○ -
U0142 - - ○ -
U0155 - - - -
U1103 - - - -
Combination Meter Assembly U0100 - - - -
U0129 - - - -
U0131 - - - -
U0142 - - ○ -
U0151 ○ - - -
U0163 - - - ○
U023A - - - ○
U1104 - - - ○
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - - -
U0124 ○ - - -
U0126 - - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - - - ○
U0126 - - - ○
U0129 - - - ○
U0142 - - ○ ○
Television Camera Assembly U0126 ○ - - ○
U0140 - - ○ ○
U0163 - - - -
U1110 - - - -
Clearance Warning ECU Assembly U0100 - - - ○
U0101 - - - ○
U0142 - - ○ ○
U0155 - - - ○
Central Gateway ECU - - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - - ○
U0125 ○ - - ○
U0126 - - - ○
U0129 - - - ○
U0235 - - - -
U023A - - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - - ○
U0125 ○ - - ○
U0126 - - - ○
U0129 - - - ○
U0235 - - - -
Forward Recognition Camera U0100 - - - ○
U0101 - - - ○
U0123 ○ - - ○
U0126 - - - ○
U0129 - - - ○
U0131 - - - ○
U0142 - - ○ ○
U0155 - - - ○
U0235 - - - -
U1104 - - - -
Millimeter Wave Radar Sensor Assembly - - - - -
Parking Assist ECU* U0100 - - - ○
U0126 - - - ○
U0129 - - - ○
U0140 - - ○ ○
U1110 - - - -
Bus 3 Radio and Display Receiver Assembly* U0100 - - - ○
U0126 - - - ○
U0129 - - - ○
U0131 - - - ○
U0140 - - ○ ○
U0155 - - - ○
U0164 - ○ - ○
U1110 - - - -
Telematics Transceiver U0100 - - - ○
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - - -
U0230 - - - -
U1002 - - - -
Multiplex Network Door ECU U0101 - - ○ -
U0122 - - ○ -
U0142 - - - -
U0155 - - ○ -
U0327 - - ○ -
Position Control ECU and Switch Assembly - - - - -

- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Engine Stop and Start ECU Communication Stop Mode
(Click here)
Power Steering ECU Communication Stop Mode
(Click here)
4WD Control ECU Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - ○ -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A - - -
U0265 - - -
U0327 - - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 ○ - -
U0121 ○ - -
U0126 ○ - -
U0131 ○ ○ -
U0140 ○ - -
U0151 ○ - -
U0155 ○ - -
U0164 ○ - -
ECM U0122 - - -
U0129 - - -
U1103 ○ - -
U1104 - - -
Power Steering ECU Assembly U0100 - ○ -
U0129 - ○ -
4WD ECU Assembly* U0100 - - ○
U0126 - - ○
U0129 - - ○
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0140 - - -
U0142 - - -
U0155 - - -
U1103 ○ - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0131 - ○ -
U0142 - - -
U0151 - - -
U0163 - - -
U023A - - -
U1104 - - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - -
U0124 - - -
U0126 - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - - -
U0126 - - -
U0129 - - -
U0142 - - -
Television Camera Assembly U0126 - - -
U0140 - - -
U0163 - - -
U1110 - - -
Clearance Warning ECU Assembly U0100 - - -
U0101 - - -
U0142 - - -
U0155 - - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
Forward Recognition Camera U0100 - - -
U0101 - - -
U0123 - - -
U0126 - - -
U0129 - - -
U0131 - ○ -
U0142 - - -
U0155 - - -
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 - - -
U0126 - - -
U0129 - - -
U0140 - - -
U1110 - - -
Bus 3 Radio and Display Receiver Assembly* U0100 - - -
U0126 - - -
U0129 - - -
U0131 - ○ -
U0140 - - -
U0155 - - -
U0164 - - -
U1110 - - -
Telematics Transceiver U0100 - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 - - -
U0122 - - -
U0142 - - -
U0155 - - -
U0327 - - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Certification ECU Communication Stop Mode
(Click here)
Steering Angle Sensor Communication Stop Mode
(Click here)
Skid Control ECU Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 ○ - -
U0129 - - ○
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A - - -
U0265 - - -
U0327 ○ - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 - - -
U0121 - - ○
U0126 - ○ -
U0131 - - -
U0140 - - -
U0151 - - -
U0155 - - -
U0164 - - -
ECM U0122 - - ○
U0129 - - ○
U1103 - - ○
U1104 - - -
Power Steering ECU Assembly U0100 - - -
U0129 - - ○
4WD ECU Assembly* U0100 - - -
U0126 - ○ -
U0129 - - ○
Certification ECU (Smart Key ECU Assembly) U0100 ○ - -
U0140 ○ - -
U0142 ○ - -
U0155 ○ - -
U1103 ○ - -
Combination Meter Assembly U0100 - - -
U0129 - - ○
U0131 - - -
U0142 - - -
U0151 - - -
U0163 - - -
U023A - - -
U1104 - - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - ○
U0124 - - ○
U0126 - ○ ○
Bus 5 Blind Spot Monitor Sensor LH U0100 - - -
U0126 - ○ -
U0129 - - ○
U0142 - - -
Television Camera Assembly U0126 - - -
U0140 - - -
U0163 - - -
U1110 - - -
Clearance Warning ECU Assembly U0100 - - -
U0101 - - -
U0142 - - -
U0155 - - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - -
U0125 - - -
U0126 - ○ -
U0129 - - ○
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - -
U0125 - - -
U0126 - ○ -
U0129 - - ○
U0235 - - -
Forward Recognition Camera U0100 - - -
U0101 - - -
U0123 - - -
U0126 - ○ -
U0129 - - ○
U0131 - - -
U0142 - - -
U0155 - - -
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 - - -
U0126 - ○ -
U0129 - - ○
U0140 - - -
U1110 - - -
Bus 3 Radio and Display Receiver Assembly* U0100 - - -
U0126 - ○ -
U0129 - - ○
U0131 - - -
U0140 - - -
U0155 - - -
U0164 - - -
U1110 - - -
Telematics Transceiver U0100 - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 - - -
U0122 - - -
U0142 - - -
U0155 - - -
U0327 ○ - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
Open in CAN main bus line(s)
Output ECU Output DTC ECM Communication Stop Mode
(Click here)
No. 6 CAN Junction Connector - No. 7 CAN Junction Connector Combination Meter ECU Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ - -
U0131 - - -
U0142 - - -
U0155 - ○ ○
Main Body ECU (Multiplex Network Body ECU) U0100 ○ - -
U0101 ○ - -
U0120 - ○ -
U0129 - ○ -
U0151 - - -
U0155 - ○ ○
U0164 - - -
U0182 - - -
U023A - ○ -
U0265 - ○ -
U0327 - ○ -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 ○ ○ -
U0121 - ○ -
U0126 - - -
U0131 - ○ -
U0140 - ○ -
U0151 - ○ -
U0155 - - ○
U0164 - ○ -
ECM U0122 ○ ○ -
U0129 ○ ○ -
U1103 ○ ○ -
U1104 - - -
Power Steering ECU Assembly U0100 ○ - -
U0129 - - -
4WD ECU Assembly* U0100 ○ ○ -
U0126 - - -
U0129 - ○ -
Certification ECU (Smart Key ECU Assembly) U0100 ○ ○ -
U0140 - ○ -
U0142 - ○ -
U0155 - - ○
U1103 - - -
Combination Meter Assembly U0100 ○ ○ ○
U0129 - ○ ○
U0131 - ○ ○
U0142 - ○ ○
U0151 - ○ ○
U0163 - - ○
U023A - - ○
U1104 - - ○
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 ○ - -
U0124 - - -
U0126 - ○ -
Bus 5 Blind Spot Monitor Sensor LH U0100 ○ ○ -
U0126 - - -
U0129 - ○ -
U0142 - ○ -
Television Camera Assembly U0126 - ○ -
U0140 - ○ -
U0163 - - -
U1110 - - -
Clearance Warning ECU Assembly U0100 ○ ○ -
U0101 ○ ○ -
U0142 - ○ -
U0155 - - ○
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 ○ ○ -
U0125 - ○ -
U0126 - - -
U0129 - ○ -
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 ○ ○ -
U0125 - ○ -
U0126 - - -
U0129 - ○ -
U0235 - - -
Forward Recognition Camera U0100 ○ ○ -
U0101 ○ ○ -
U0123 - ○ -
U0126 - - -
U0129 - ○ -
U0131 - ○ -
U0142 - ○ -
U0155 - - ○
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 ○ ○ -
U0126 - - -
U0129 - ○ -
U0140 - ○ -
U1110 - - -
Bus 3 Radio and Display Receiver Assembly* U0100 ○ ○ -
U0126 - - -
U0129 - ○ -
U0131 - ○ -
U0140 - ○ -
U0155 - - ○
U0164 - ○ -
U1110 - - -
Telematics Transceiver U0100 ○ ○ -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 ○ - -
U0122 ○ - -
U0142 - - -
U0155 - ○ ○
U0327 - ○ -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
CAN bus lines short circuit or short to GND
Output ECU Output DTC CANH - CANL
CANH - GND
CANL - GND
Bus 2 Airbag Sensor Assembly - -
Air Conditioning Amplifier Assembly U0100 ○
U0131 ○
U0142 ○
U0155 ○
Main Body ECU (Multiplex Network Body ECU) U0100 ○
U0101 ○
U0120 ○
U0129 ○
U0151 ○
U0155 ○
U0164 ○
U0182 ○
U023A ○
U0265 ○
U0327 ○
Central Gateway ECU - -
Engine Stop and Start ECU U0100 ○
U0121 ○
U0126 ○
U0131 ○
U0140 ○
U0151 ○
U0155 ○
U0164 ○
ECM U0122 ○
U0129 ○
U1103 ○
U1104 ○
Power Steering ECU Assembly U0100 ○
U0129 ○
4WD ECU Assembly* U0100 ○
U0126 ○
U0129 ○
Certification ECU (Smart Key ECU Assembly) U0100 ○
U0140 ○
U0142 ○
U0155 ○
U1103 ○
Combination Meter Assembly U0100 ○
U0129 ○
U0131 ○
U0142 ○
U0151 ○
U0163 ○
U023A ○
U1104 ○
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -
Brake Actuator Assembly (Skid Control ECU)* U0100 ○
U0124 ○
U0126 ○
Bus 5 Blind Spot Monitor Sensor LH U0100 ○
U0126 ○
U0129 ○
U0142 ○
Television Camera Assembly U0126 ○
U0140 ○
U0163 -
U1110 -
Clearance Warning ECU Assembly U0100 ○
U0101 ○
U0142 ○
U0155 ○
Central Gateway ECU - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 ○
U0125 ○
U0126 ○
U0129 ○
U0235 -
U023A -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 ○
U0125 ○
U0126 ○
U0129 ○
U0235 -
Forward Recognition Camera U0100 ○
U0101 ○
U0123 ○
U0126 ○
U0129 ○
U0131 ○
U0142 ○
U0155 ○
U0235 -
U1104 -
Millimeter Wave Radar Sensor Assembly - -
Parking Assist ECU* U0100 ○
U0126 ○
U0129 ○
U0140 ○
U1110 -
Bus 3 Radio and Display Receiver Assembly* U0100 ○
U0126 ○
U0129 ○
U0131 ○
U0140 ○
U0155 ○
U0164 ○
U1110 -
Telematics Transceiver U0100 ○
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 -
U0230 -
U1002 -
Multiplex Network Door ECU U0101 ○
U0122 ○
U0142 -
U0155 ○
U0327 ○
Position Control ECU and Switch Assembly - -



DTC COMBINATION TABLE (OPEN OR SHORT IN BUS 3, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU and sensor connected to the bus 3 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN bus line(s) and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN bus line(s) does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a short to ground or +B in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 8 to 16) first.

·

If an open occurs in just one of the lines of a CAN bus line(s), DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.

·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Audio Receiver Assembly Communication Stop Mode
(Click here)
DCM Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - -
Air Conditioning Amplifier Assembly U0100 - -
U0131 - -
U0142 - -
U0155 - -
Main Body ECU (Multiplex Network Body ECU) U0100 - -
U0101 - -
U0120 - -
U0129 - -
U0151 - -
U0155 - -
U0164 - -
U0182 - -
U023A - -
U0265 - -
U0327 - -
Central Gateway ECU - - -
Engine Stop and Start ECU U0100 - -
U0121 - -
U0126 - -
U0131 - -
U0140 - -
U0151 - -
U0155 - -
U0164 - -
ECM U0122 - -
U0129 - -
U1103 - -
U1104 - -
Power Steering ECU Assembly U0100 - -
U0129 - -
4WD ECU Assembly* U0100 - -
U0126 - -
U0129 - -
Certification ECU (Smart Key ECU Assembly) U0100 - -
U0140 - -
U0142 - -
U0155 - -
U1103 - -
Combination Meter Assembly U0100 - -
U0129 - -
U0131 - -
U0142 - -
U0151 - -
U0163 ○ -
U023A - -
U1104 - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - -
U0124 - -
U0126 - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - -
U0126 - -
U0129 - -
U0142 - -
Television Camera Assembly U0126 - -
U0140 - -
U0163 ○ -
U1110 - -
Clearance Warning ECU Assembly U0100 - -
U0101 - -
U0142 - -
U0155 - -
Central Gateway ECU - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - -
U0125 - -
U0126 - -
U0129 - -
U0235 - -
U023A - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - -
U0125 - -
U0126 - -
U0129 - -
U0235 - -
Forward Recognition Camera U0100 - -
U0101 - -
U0123 - -
U0126 - -
U0129 - -
U0131 - -
U0142 - -
U0155 - -
U0235 - -
U1104 - -
Millimeter Wave Radar Sensor Assembly - - -
Parking Assist ECU* U0100 - -
U0126 - -
U0129 - -
U0140 - -
U1110 - -
Bus 3 Radio and Display Receiver Assembly* U0100 ○ -
U0126 ○ -
U0129 ○ -
U0131 ○ -
U0140 ○ -
U0155 ○ -
U0164 ○ -
U1110 ○ -
Telematics Transceiver U0100 - ○
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - -
U0230 - -
U1002 - -
Multiplex Network Door ECU U0101 - -
U0122 - -
U0142 - -
U0155 - -
U0327 - -
Position Control ECU and Switch Assembly - - -

- Trouble Mode
Open in CAN main bus line(s)
Output ECU Output DTC Central Gateway ECU Communication Stop Mode (CA3H, CA3L) No. 8 CAN Junction Connector - No. 13 CAN Junction Connector
(w/ Telematics Transceiver)
No. 13 CAN Junction Connector - Central Gateway ECU Communication Stop Mode (CAYH, CAYL)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A - - -
U0265 - - -
U0327 - - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 - - -
U0121 - - -
U0126 - - -
U0131 - - -
U0140 - - -
U0151 - - -
U0155 - - -
U0164 - - -
ECM U0122 - - -
U0129 - - -
U1103 - - -
U1104 - - -
Power Steering ECU Assembly U0100 - - -
U0129 - - -
4WD ECU Assembly* U0100 - - -
U0126 - - -
U0129 - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0140 - - -
U0142 - - -
U0155 - - -
U1103 - - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0151 - - -
U0163 ○ - -
U023A - - -
U1104 - - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - -
U0124 - -
U0126 - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - - -
U0126 - - -
U0129 - - -
U0142 - - -
Television Camera Assembly U0126 - - -
U0140 - - -
U0163 ○ - -
U1110 - - -
Clearance Warning ECU Assembly U0100 - - -
U0101 - - -
U0142 - - -
U0155 - - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
Forward Recognition Camera U0100 - - -
U0101 - - -
U0123 - - -
U0126 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0155 - - -
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 - - -
U0126 - - -
U0129 - - -
U0140 - - -
U1110 - - -
Bus 3 Radio and Display Receiver Assembly* U0100 ○ - -
U0126 ○ - -
U0129 ○ - -
U0131 ○ - -
U0140 ○ - -
U0155 ○ - -
U0164 ○ - -
U1110 ○ - -
Telematics Transceiver U0100 ○ - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 - - -
U0122 - - -
U0142 - - -
U0155 - - -
U0327 - - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
CAN bus lines short circuit or short to GND
Output ECU Output DTC CANH - CANL
CANH - GND
CANL - GND
Bus 2 Airbag Sensor Assembly - -
Air Conditioning Amplifier Assembly U0100 -
U0131 -
U0142 -
U0155 -
Main Body ECU (Multiplex Network Body ECU) U0100 -
U0101 -
U0120 -
U0129 -
U0151 -
U0155 -
U0164 -
U0182 -
U023A -
U0265 -
U0327 -
Central Gateway ECU - -
Engine Stop and Start ECU U0100 -
U0121 -
U0126 -
U0131 -
U0140 -
U0151 -
U0155 -
U0164 -
ECM U0122 -
U0129 -
U1103 -
U1104 -
Power Steering ECU Assembly U0100 -
U0129 -
4WD ECU Assembly* U0100 -
U0126 -
U0129 -
Certification ECU (Smart Key ECU Assembly) U0100 -
U0140 -
U0142 -
U0155 -
U1103 -
Combination Meter Assembly U0100 -
U0129 -
U0131 -
U0142 -
U0151 -
U0163 ○
U023A -
U1104 -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -
Brake Actuator Assembly (Skid Control ECU)* U0100 -
U0124 -
U0126 -
Bus 5 Blind Spot Monitor Sensor LH U0100 -
U0126 -
U0129 -
U0142 -
Television Camera Assembly U0126 -
U0140 -
U0163 ○
U1110 -
Clearance Warning ECU Assembly U0100 -
U0101 -
U0142 -
U0155 -
Central Gateway ECU - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 -
U0125 -
U0126 -
U0129 -
U0235 -
U023A -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 -
U0125 -
U0126 -
U0129 -
U0235 -
Forward Recognition Camera U0100 -
U0101 -
U0123 -
U0126 -
U0129 -
U0131 -
U0142 -
U0155 -
U0235 -
U1104 -
Millimeter Wave Radar Sensor Assembly - -
Parking Assist ECU* U0100 -
U0126 -
U0129 -
U0140 -
U1110 -
Bus 3 Radio and Display Receiver Assembly* U0100 ○
U0126 ○
U0129 ○
U0131 ○
U0140 ○
U0155 ○
U0164 ○
U1110 ○
Telematics Transceiver U0100 ○
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 -
U0230 -
U1002 -
Multiplex Network Door ECU U0101 -
U0122 -
U0142 -
U0155 -
U0327 -
Position Control ECU and Switch Assembly - -



DTC COMBINATION TABLE (OPEN OR SHORT IN BUS 5, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU and sensor connected to the bus 5 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN bus line(s) and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN bus line(s) does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a short to ground or +B in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 8 to 16) first.

·

If an open occurs in just one of the lines of a CAN bus line(s), DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.

·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Blind Spot Monitor Sensor Communication Stop Mode
(Click here)
Television Camera ECU Communication Stop Mode
(Click here)
Clearance Warning ECU Communication Stop Mode
(Click here)
Driving Support ECU Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - - - -
Air Conditioning Amplifier Assembly U0100 - - - -
U0131 - - - -
U0142 - - - -
U0155 - - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - - -
U0101 - - - -
U0120 - - - -
U0129 - - - -
U0151 - - - -
U0155 - - - -
U0164 - - - -
U0182 - - - -
U023A - - - -
U0265 - - - -
U0327 - - - -
Central Gateway ECU - - - - -
Engine Stop and Start ECU U0100 - - - -
U0121 - - - -
U0126 - - - -
U0131 - - - -
U0140 - - - -
U0151 - - - -
U0155 - - - -
U0164 - - - -
ECM U0122 - - - -
U0129 - - - -
U1103 - - - -
U1104 - - - ○
Power Steering ECU Assembly U0100 - - - -
U0129 - - - -
4WD ECU Assembly* U0100 - - - -
U0126 - - - -
U0129 - - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - - -
U0140 - - - -
U0142 - - - -
U0155 - - - -
U1103 - - - -
Combination Meter Assembly U0100 - - - -
U0129 - - - -
U0131 - - - -
U0142 - - - -
U0151 - - - -
U0163 - - - -
U023A - - - -
U1104 - - - ○
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - - -
U0124 - - - -
U0126 - - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 ○ - - -
U0126 ○ - - -
U0129 ○ - - -
U0142 ○ - - -
Television Camera Assembly U0126 - ○ - -
U0140 - ○ - -
U0163 - ○ - -
U1110 - ○ ○ -
Clearance Warning ECU Assembly U0100 - - ○ -
U0101 - - ○ -
U0142 - - ○ -
U0155 - - ○ -
Central Gateway ECU - - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - - ○
U0125 - - - ○
U0126 - - - ○
U0129 - - - ○
U0235 - - - ○
U023A - - - ○
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - - ○
U0125 - - - ○
U0126 - - - ○
U0129 - - - ○
U0235 - - - ○
Forward Recognition Camera U0100 - - - -
U0101 - - - -
U0123 - - - -
U0126 - - - -
U0129 - - - -
U0131 - - - -
U0142 - - - -
U0155 - - - -
U0235 - - - -
U1104 - - - ○
Millimeter Wave Radar Sensor Assembly - - - - -
Parking Assist ECU* U0100 - - - -
U0126 - - - -
U0129 - - - -
U0140 - - - -
U1110 - - ○ -
Bus 3 Radio and Display Receiver Assembly* U0100 - - - -
U0126 - - - -
U0129 - - - -
U0131 - - - -
U0140 - - - -
U0155 - - - -
U0164 - - - -
U1110 - - ○ -
Telematics Transceiver U0100 - - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - - -
U0230 - - - -
U1002 - - - -
Multiplex Network Door ECU U0101 - - - -
U0122 - - - -
U0142 - - - -
U0155 - - - -
U0327 - - - -
Position Control ECU and Switch Assembly - - - - -

- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Front Camera Module Communication Stop Mode
(Click here)
Millimeter Wave Radar Sensor Communication Stop Mode
(Click here)
Parking Assist ECU Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A ○ - -
U0265 - - ○
U0327 - - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 - - -
U0121 - - -
U0126 - - -
U0131 - - -
U0140 - - -
U0151 - - -
U0155 - - -
U0164 - - -
ECM U0122 - - -
U0129 - - -
U1103 - - -
U1104 - - -
Power Steering ECU Assembly U0100 - - -
U0129 - - -
4WD ECU Assembly* U0100 - - -
U0126 - - -
U0129 - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0140 - - -
U0142 - - -
U0155 - - -
U1103 - - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0151 - - -
U0163 - - -
U023A ○ - -
U1104 - - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - -
U0124 - - -
U0126 - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - - -
U0126 - - -
U0129 - - -
U0142 - - -
Television Camera Assembly U0126 - - -
U0140 - - -
U0163 - - -
U1110 - - -
Clearance Warning ECU Assembly U0100 - - -
U0101 - - -
U0142 - - -
U0155 - - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - ○ -
U023A ○ - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - ○ -
Forward Recognition Camera U0100 ○ - -
U0101 ○ - -
U0123 ○ - -
U0126 ○ - -
U0129 ○ - -
U0131 ○ - -
U0142 ○ - -
U0155 ○ - -
U0235 ○ ○ -
U1104 ○ - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 - - ○
U0126 - - ○
U0129 - - ○
U0140 - - ○
U1110 - - ○
Bus 3 Radio and Display Receiver Assembly* U0100 - - -
U0126 - - -
U0129 - - -
U0131 - - -
U0140 - - -
U0155 - - -
U0164 - - -
U1110 - - -
Telematics Transceiver U0100 - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 - - -
U0122 - - -
U0142 - - -
U0155 - - -
U0327 - - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
Open in CAN main bus line(s)
Output ECU Output DTC Central Gateway ECU Communication Stop Mode (CA5H, CA5L) No. 9 CAN Junction Connector - No. 10 CAN Junction Connector Central Gateway ECU Communication Stop Mode (CAXH, CAXL)
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A ○ - -
U0265 ○ ○ -
U0327 - - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 - - -
U0121 - - -
U0126 - - -
U0131 - - -
U0140 - - -
U0151 - - -
U0155 - - -
U0164 - - -
ECM U0122 - - -
U0129 - - -
U1103 - - -
U1104 ○ - -
Power Steering ECU Assembly U0100 - - -
U0129 - - -
4WD ECU Assembly* U0100 - - -
U0126 - - -
U0129 - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0140 - - -
U0142 - - -
U0155 - - -
U1103 - - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0151 - - -
U0163 - - -
U023A ○ - -
U1104 ○ - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - -
U0124 - - -
U0126 - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 ○ ○ -
U0126 ○ ○ -
U0129 ○ ○ -
U0142 ○ ○ -
Television Camera Assembly U0126 ○ ○ -
U0140 ○ ○ -
U0163 ○ ○ -
U1110 - ○ -
Clearance Warning ECU Assembly U0100 ○ - -
U0101 ○ - -
U0142 ○ - -
U0155 ○ - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 ○ - -
U0125 ○ - -
U0126 ○ - -
U0129 ○ - -
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 ○ - -
U0125 ○ - -
U0126 ○ - -
U0129 ○ - -
U0235 - - -
Forward Recognition Camera U0100 ○ - -
U0101 ○ - -
U0123 ○ - -
U0126 ○ - -
U0129 ○ - -
U0131 ○ - -
U0142 ○ - -
U0155 ○ - -
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 ○ ○ -
U0126 ○ ○ -
U0129 ○ ○ -
U0140 ○ ○ -
U1110 - ○ -
Bus 3 Radio and Display Receiver Assembly* U0100 - - -
U0126 - - -
U0129 - - -
U0131 - - -
U0140 - - -
U0155 - - -
U0164 - - -
U1110 ○ - -
Telematics Transceiver U0100 - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - - -
U0230 - - -
U1002 - - -
Multiplex Network Door ECU U0101 - - -
U0122 - - -
U0142 - - -
U0155 - - -
U0327 - - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
CAN bus lines short circuit or short to GND
Output ECU Output DTC CANH - CANL
CANH - GND
CANL - GND
Bus 2 Airbag Sensor Assembly - -
Air Conditioning Amplifier Assembly U0100 -
U0131 -
U0142 -
U0155 -
Main Body ECU (Multiplex Network Body ECU) U0100 -
U0101 -
U0120 -
U0129 -
U0151 -
U0155 -
U0164 -
U0182 -
U023A ○
U0265 ○
U0327 -
Central Gateway ECU - -
Engine Stop and Start ECU U0100 -
U0121 -
U0126 -
U0131 -
U0140 -
U0151 -
U0155 -
U0164 -
ECM U0122 -
U0129 -
U1103 -
U1104 ○
Power Steering ECU Assembly U0100 -
U0129 -
4WD ECU Assembly* U0100 -
U0126 -
U0129 -
Certification ECU (Smart Key ECU Assembly) U0100 -
U0140 -
U0142 -
U0155 -
U1103 -
Combination Meter Assembly U0100 -
U0129 -
U0131 -
U0142 -
U0151 -
U0163 -
U023A ○
U1104 ○
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -
Brake Actuator Assembly (Skid Control ECU)* U0100 -
U0124 -
U0126 -
Bus 5 Blind Spot Monitor Sensor LH U0100 ○
U0126 ○
U0129 ○
U0142 ○
Television Camera Assembly U0126 ○
U0140 ○
U0163 ○
U1110 ○
Clearance Warning ECU Assembly U0100 ○
U0101 ○
U0142 ○
U0155 ○
Central Gateway ECU - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 ○
U0125 ○
U0126 ○
U0129 ○
U0235 ○
U023A ○
Driving Support ECU Assembly
<Radar Cruise2>
U0100 ○
U0125 ○
U0126 ○
U0129 ○
U0235 ○
Forward Recognition Camera U0100 ○
U0101 ○
U0123 ○
U0126 ○
U0129 ○
U0131 ○
U0142 ○
U0155 ○
U0235 ○
U1104 ○
Millimeter Wave Radar Sensor Assembly - -
Parking Assist ECU* U0100 ○
U0126 ○
U0129 ○
U0140 ○
U1110 ○
Bus 3 Radio and Display Receiver Assembly* U0100 -
U0126 -
U0129 -
U0131 -
U0140 -
U0155 -
U0164 -
U1110 ○
Telematics Transceiver U0100 -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 -
U0230 -
U1002 -
Multiplex Network Door ECU U0101 -
U0122 -
U0142 -
U0155 -
U0327 -
Position Control ECU and Switch Assembly - -



DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 1, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of ECUs and sensors connected to sub bus 1 (in this case, normal is displayed for CAN Bus Check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the main body ECU (multiplex network body ECU).

HINT:
·

As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.

·

DTCs output from ECUs other than the network gateway ECU (gateway function equipped ECU) are shown only as a reference.

·

Regarding a communication stop that is currently occurring in sub bus 1, the malfunctioning part can be confirmed easily by performing CAN Bus Check using the GTS.

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.

·

○: DTC is output.

·

-: DTC is not output.

·

*: DTC U0073 may be stored when communication is lost.



- Trouble Mode
Open in CAN branch line(s)
Output ECU Output DTC Multiplex Network Door ECU Stop Mode
(Click here)
Position Control ECU and Switch Assembly Communication Stop Mode
(Click here)
Bus 2 Airbag Sensor Assembly - - -
Air Conditioning Amplifier Assembly U0100 - -
U0131 - -
U0142 - -
U0155 - -
Main Body ECU (Multiplex Network Body ECU) U0100 - -
U0101 - -
U0120 - -
U0129 - -
U0151 - -
U0155 - -
U0164 - -
U0182 - -
U023A - -
U0265 - -
U0327 - -
Central Gateway ECU - - -
Engine Stop and Start ECU U0100 - -
U0121 - -
U0126 - -
U0131 - -
U0140 - -
U0151 - -
U0155 - -
U0164 - -
ECM U0122 - -
U0129 - -
U1103 - -
U1104 - -
Power Steering ECU Assembly U0100 - -
U0129 - -
4WD ECU Assembly* U0100 - -
U0126 - -
U0129 - -
Certification ECU (Smart Key ECU Assembly) U0100 - -
U0140 - -
U0142 - -
U0155 - -
U1103 - -
Combination Meter Assembly U0100 - -
U0129 - -
U0131 - -
U0142 - -
U0151 - -
U0163 - -
U023A - -
U1104 - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - -
U0124 - -
U0126 - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - -
U0126 - -
U0129 - -
U0142 - -
Television Camera Assembly U0126 - -
U0140 - -
U0163 - -
U1110 - -
Clearance Warning ECU Assembly U0100 - -
U0101 - -
U0142 - -
U0155 - -
Central Gateway ECU - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - -
U0125 - -
U0126 - -
U0129 - -
U0235 - -
U023A - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - -
U0125 - -
U0126 - -
U0129 - -
U0235 - -
Forward Recognition Camera U0100 - -
U0101 - -
U0123 - -
U0126 - -
U0129 - -
U0131 - -
U0142 - -
U0155 - -
U0235 - -
U1104 - -
Millimeter Wave Radar Sensor Assembly - - -
Parking Assist ECU* U0100 - -
U0126 - -
U0129 - -
U0140 - -
U1110 - -
Bus 3 Radio and Display Receiver Assembly* U0100 - -
U0126 - -
U0129 - -
U0131 - -
U0140 - -
U0155 - -
U0164 - -
U1110 - -
Telematics Transceiver U0100 - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 - ○
U0230 ○ -
U1002 - -
Multiplex Network Door ECU U0101 ○ -
U0122 ○ -
U0142 ○ -
U0155 ○ -
U0327 ○ -
Position Control ECU and Switch Assembly - - -

- Trouble Mode
Open in CAN main bus line(s)
Output ECU Output DTC Main Body ECU Communication Stop Mode
(Click here)
No. 4 CAN Junction Connector - No. 5 CAN Junction Connector
(w/ Seat Memory)
No. 5 CAN Junction Connector - No. 1 CAN Junction Terminal
Bus 2 Airbag Sensor Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0131 - - -
U0142 - - -
U0155 - - -
Main Body ECU (Multiplex Network Body ECU) U0100 - - -
U0101 - - -
U0120 - - -
U0129 - - -
U0151 - - -
U0155 - - -
U0164 - - -
U0182 - - -
U023A - - -
U0265 - - -
U0327 - - -
Central Gateway ECU - - - -
Engine Stop and Start ECU U0100 - - -
U0121 - - -
U0126 - - -
U0131 - - -
U0140 - - -
U0151 - - -
U0155 - - -
U0164 - - -
ECM U0122 - - -
U0129 - - -
U1103 - - -
U1104 - - -
Power Steering ECU Assembly U0100 - - -
U0129 - - -
4WD ECU Assembly* U0100 - - -
U0126 - - -
U0129 - - -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0140 - - -
U0142 - - -
U0155 - - -
U1103 - - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0151 - - -
U0163 - - -
U023A - - -
U1104 - - -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - - - -
Brake Actuator Assembly (Skid Control ECU)* U0100 - - -
U0124 - - -
U0126 - - -
Bus 5 Blind Spot Monitor Sensor LH U0100 - - -
U0126 - - -
U0129 - - -
U0142 - - -
Television Camera Assembly U0126 - - -
U0140 - - -
U0163 - - -
U1110 - - -
Clearance Warning ECU Assembly U0100 - - -
U0101 - - -
U0142 - - -
U0155 - - -
Central Gateway ECU - - - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
U023A - - -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 - - -
U0125 - - -
U0126 - - -
U0129 - - -
U0235 - - -
Forward Recognition Camera U0100 - - -
U0101 - - -
U0123 - - -
U0126 - - -
U0129 - - -
U0131 - - -
U0142 - - -
U0155 - - -
U0235 - - -
U1104 - - -
Millimeter Wave Radar Sensor Assembly - - - -
Parking Assist ECU* U0100 - - -
U0126 - - -
U0129 - - -
U0140 - - -
U1110 - - -
Bus 3 Radio and Display Receiver Assembly* U0100 - - -
U0126 - - -
U0129 - - -
U0131 - - -
U0140 - - -
U0155 - - -
U0164 - - -
U1110 - - -
Telematics Transceiver U0100 - - -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 ○ - -
U0230 ○ ○ -
U1002 - - -
Multiplex Network Door ECU U0101 ○ ○ -
U0122 ○ ○ -
U0142 ○ ○ -
U0155 - - -
U0327 - - -
Position Control ECU and Switch Assembly - - - -

- Trouble Mode
CAN bus lines short circuit or short to GND
Output ECU Output DTC CANH - CANL
CANH - GND
CANL - GND
Bus 2 Airbag Sensor Assembly - -
Air Conditioning Amplifier Assembly U0100 -
U0131 -
U0142 -
U0155 -
Main Body ECU (Multiplex Network Body ECU) U0100 -
U0101 -
U0120 -
U0129 -
U0151 -
U0155 -
U0164 -
U0182 -
U023A -
U0265 -
U0327 -
Central Gateway ECU - -
Engine Stop and Start ECU U0100 -
U0121 -
U0126 -
U0131 -
U0140 -
U0151 -
U0155 -
U0164 -
ECM U0122 -
U0129 -
U1103 -
U1104 -
Power Steering ECU Assembly U0100 -
U0129 -
4WD ECU Assembly* U0100 -
U0126 -
U0129 -
Certification ECU (Smart Key ECU Assembly) U0100 -
U0140 -
U0142 -
U0155 -
U1103 -
Combination Meter Assembly U0100 -
U0129 -
U0131 -
U0142 -
U0151 -
U0163 -
U023A -
U1104 -
Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) - -
Brake Actuator Assembly (Skid Control ECU)* U0100 -
U0124 -
U0126 -
Bus 5 Blind Spot Monitor Sensor LH U0100 -
U0126 -
U0129 -
U0142 -
Television Camera Assembly U0126 -
U0140 -
U0163 -
U1110 -
Clearance Warning ECU Assembly U0100 -
U0101 -
U0142 -
U0155 -
Central Gateway ECU - -
Driving Support ECU Assembly
<Pre-Crash 2>
U0100 -
U0125 -
U0126 -
U0129 -
U0235 -
U023A -
Driving Support ECU Assembly
<Radar Cruise2>
U0100 -
U0125 -
U0126 -
U0129 -
U0235 -
Forward Recognition Camera U0100 -
U0101 -
U0123 -
U0126 -
U0129 -
U0131 -
U0142 -
U0155 -
U0235 -
U1104 -
Millimeter Wave Radar Sensor Assembly - -
Parking Assist ECU* U0100 -
U0126 -
U0129 -
U0140 -
U1110 -
Bus 3 Radio and Display Receiver Assembly* U0100 -
U0126 -
U0129 -
U0131 -
U0140 -
U0155 -
U0164 -
U1110 -
Telematics Transceiver U0100 -
Sub Bus 1 Main Body ECU (Multiplex Network Body ECU) U0208 ○
U0230 ○
U1002 ○
Multiplex Network Door ECU U0101 ○
U0122 ○
U0142 ○
U0155 ○
U0327 ○
Position Control ECU and Switch Assembly - -



CAN BUS WAVEFORMS


C353604E03
1.521,0.677 1.854,0.281 1.854,0.281 1.99,0.281 false 4.427,1 4.427,0.271 4.427,0.271 4.563,0.271 true 4.438,3.948 4.438,2.521 4.438,2.521 5.219,2.521 true 6.354,3.948 6.354,2.521 6.354,2.521 5.646,2.521 true 5.375,3.688 5.375,4.781 5.375,4.781 5.51,4.781 false 2.063,0.208 3.208,0.448 1.146,0.24 10 false CAN Main Bus 4.656,0.198 7.052,0.479 2.396,0.281 10 false Open in CAN Main Bus Line (CANH) 5.313,3.167 6.385,3.365 1.073,0.198 10 false ECU 3.417,3.167 4.49,3.365 1.073,0.198 10 false ECU 1.594,3.167 2.667,3.365 1.073,0.198 10 false ECU 3.885,4.01 5.208,4.531 1.323,0.521 10 false Open in CAN Branch Line (CANL) 5.76,4 7.073,4.49 1.313,0.49 10 false Open in CAN Branch Line (CANH) 5.604,4.708 6.708,5.177 1.104,0.469 10 false CAN Branch 1.469,4.781 3.802,5.031 2.333,0.25 10 false : CAN Main Bus Line (CANH) 1.479,5.219 3.677,5.521 2.198,0.302 10 false : CAN Main Bus Line (CANL) 1.479,5.813 3.51,6.094 2.031,0.281 10 false : CAN Branch Line (CANH) 1.469,6.25 3.625,6.521 2.156,0.271 10 false : CAN Branch Line (CANL)

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main wire, an open in a CAN branch wire, or a short between a CAN wire (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973N04
0.5,1.5 0.667,1.5 0.667,1.5 0.917,1.167 true 0.5,0.5 0.667,0.5 0.667,0.5 0.906,0.781 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.708,0.25 3.427,0.448 0.719,0.198 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Normal waveform


ii.
C265974N03
1.5,1.417 1.667,1.417 1.667,1.417 1.969,1.104 true 1.5,0.5 1.667,0.5 1.667,0.5 1.969,0.792 true 1.052,0.417 1.667,0.615 0.615,0.198 10 CANH 1.135,1.333 1.75,1.531 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND 2.667,0.24 3.354,0.417 0.688,0.177 10 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not output from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975N03
0.5,1.333 0.75,1.333 0.75,1.333 1.063,0.969 true 1.292,0.917 0.729,0.583 0.729,0.583 0.5,0.583 true 0.083,0.5 0.698,0.698 0.615,0.198 10 CANH 0.135,1.25 0.75,1.448 0.615,0.198 10 CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 50 μs/DIV. 2.729,0.271 3.354,0.479 0.625,0.208 10 1 V/DIV. 2.938,1.385 3.396,1.583 0.458,0.198 10 GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976N03
0.938,0.76 0.667,0.5 0.667,0.5 0.5,0.5 true 0.5,1.5 0.667,1.5 0.667,1.5 0.844,1.167 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.417 0.75,1.615 0.615,0.198 10 CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 50 μs/DIV. 2.708,0.281 3.344,0.5 0.635,0.219 10 1 V/DIV. 2.969,1.385 3.427,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




ii.
C265977N03
0.5,1.417 0.667,1.417 0.667,1.417 0.906,1.146 true 0.5,0.5 0.667,0.5 0.667,0.5 0.833,0.74 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.344 0.75,1.542 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.417,0.51 0.719,0.229 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Open in a CAN branch wire (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch wires. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch wire is disconnected.




iii.
C265978N03
0.5,0.5 0.667,0.5 0.667,0.5 0.938,0.708 true 0.5,1.417 0.75,1.417 0.75,1.417 0.938,1.156 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.333 0.75,1.531 0.615,0.198 10 CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 50 μs/DIV. 2.698,0.281 3.281,0.521 0.583,0.24 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Open in a CAN main wire (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main wire can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979N03
0.5,1.75 0.75,1.75 0.75,1.75 1.083,1.531 true 1.063,1.333 0.75,0.917 0.75,0.917 0.5,0.917 true 0.083,0.833 0.698,1.031 0.615,0.198 10 CANH 0.083,1.667 0.698,1.865 0.615,0.198 10 CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 50 μs/DIV. 2.719,0.302 3.375,0.552 0.656,0.25 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980N03
0.5,1.583 0.667,1.583 0.667,1.583 0.833,1.385 true 0.5,0.5 0.667,0.5 0.667,0.5 1.021,0.708 true 0.083,0.417 0.698,0.615 0.615,0.198 10 CANH 0.135,1.5 0.75,1.698 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.698,0.271 3.292,0.531 0.594,0.26 10 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connector(s) from the CAN junction connector(s) or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data content Data Detected and Sent by Data Received from
(Can be Checked in Data List)
Data Received
(Cannot be Checked in Data List)
Relevant Data List Item
[Selected System]

*: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.

Engine speed ECM
·

Brake actuator assembly (skid control ECU)

·

Combination meter assembly

·

Power steering ECU assembly

·

Engine stop and start ECU


·

Air conditioning amplifier assembly

·

4WD ECU assembly

·

Certification ECU (smart key ECU assembly)

·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Radio and display receiver assembly


·

ECM [Engine and ECT]

·

ECM [Engine]

·

Brake actuator assembly (skid control ECU) [ABS/VSC/TRC]

·

Combination meter assembly [Combination Meter]

·

Power steering ECU assembly [EMPS]

·

Engine stop and start ECU [Stop and Start]


Engine coolant temperature ECM
·

4WD ECU assembly

·

Power steering ECU assembly

·

Air conditioning amplifier assembly

·

Combination meter assembly


Power steering ECU assembly
·

ECM [Engine and ECT]

·

ECM [Engine]

·

4WD ECU assembly [Four Wheel Drive]

·

Combination meter assembly [Combination Meter]

·

Air conditioning amplifier assembly [Air Conditioner]


Stop light switch Brake actuator assembly (skid control ECU)
·

4WD ECU assembly

·

Engine stop and start ECU


·

Power steering ECU assembly

·

Blind spot monitor sensor LH

·

Multiplex network door ECU

·

Airbag sensor assembly

·

Driving support ECU assembly


·

Brake actuator assembly (skid control ECU) [ABS/VSC/TRC]

·

4WD ECU assembly [Four Wheel Drive]

·

Engine stop and start ECU [Stop and Start]


Wheel speed signal Brake actuator assembly (skid control ECU) 4WD ECU assembly
·

ECM

·

Power steering ECU assembly

·

Blind spot monitor sensor LH

·

Forward recognition camera

·

Airbag sensor assembly

·

Driving support ECU assembly

·

Parking assist ECU

·

Engine stop and start ECU


·

Brake actuator assembly (skid control ECU) [ABS/VSC/TRC]

·

4WD ECU assembly [Four Wheel Drive]


Steering angle signal Spiral with sensor cable sub-assembly (steering angle sensor)
·

Brake actuator assembly (skid control ECU)

·

4WD ECU assembly

·

Blind spot monitor sensor LH

·

Power steering ECU assembly

·

Driving support ECU assembly


·

Airbag sensor assembly

·

Radio and display receiver assembly

·

Forward recognition camera

·

Parking assist ECU

·

Television camera assembly


·

Brake actuator assembly (skid control ECU) [ABS/VSC/TRC]

·

Blind spot monitor sensor LH [Blind Spot Monitor Master]

·

4WD ECU assembly [Four Wheel Drive]

·

Power steering ECU assembly [EMPS]

·

Driving support ECU assembly [Radar Cruise2]


Turn signal switch signal Combination meter assembly
·

Blind spot monitor sensor LH

·

Forward recognition camera

·

Driving support ECU assembly


-
·

Combination meter assembly [Combination Meter]

·

Blind spot monitor sensor LH [Blind Spot Monitor Master]

·

Forward recognition camera [LDA/LKA]


Vehicle speed Brake actuator assembly (skid control ECU)
·

ECM

·

Combination meter assembly

·

Blind spot monitor sensor LH

·

Power steering ECU assembly

·

Radio and display receiver assembly

·

Driving support ECU assembly

·

Engine stop and start ECU


·

Airbag sensor assembly

·

Forward recognition camera

·

Parking assist ECU

·

Telematics transceiver


·

Brake actuator assembly (skid control ECU) [ABS/VSC/TRC]

·

ECM [Engine and ECT]

·

ECM [Engine]

·

Combination meter assembly [Combination Meter]

·

Blind spot monitor sensor LH [Blind Spot Monitor Master]

·

Power steering ECU assembly [EMPS]

·

Radio and display receiver assembly [Navigation System]

·

Driving support ECU assembly [Radar Cruise2]

·

Engine stop and start ECU [Stop and Start]


Combination meter assembly* -
·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Multiplex network door ECU

·

Certification ECU (smart key ECU assembly)

·

Clearance warning ECU assembly


Combination meter assembly [Combination Meter]
Ambient temperature Combination meter assembly
·

Air conditioning amplifier assembly

·

4WD ECU assembly


·

Clearance warning ECU assembly

·

Driving support ECU assembly


·

Combination meter assembly [Combination Meter]

·

Air conditioning amplifier assembly [Air Conditioner]

·

4WD ECU assembly [Four Wheel Drive]


FL door courtesy Main body ECU (multiplex network body ECU) -
·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Engine stop and start ECU


Main body ECU (multiplex network body ECU) [Main Body]
FR door courtesy Main body ECU (multiplex network body ECU) -
·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Engine stop and start ECU


Main body ECU (multiplex network body ECU) [Main Body]
RL door courtesy Main body ECU (multiplex network body ECU) -
·

Combination meter assembly

·

Engine stop and start ECU


Main body ECU (multiplex network body ECU) [Main Body]
RR door courtesy Main body ECU (multiplex network body ECU) -
·

Combination meter assembly

·

Engine stop and start ECU


Main body ECU (multiplex network body ECU) [Main Body]
Back door courtesy Main body ECU (multiplex network body ECU) -
·

Radio and display receiver assembly

·

Certification ECU (smart key ECU assembly)

·

Combination meter assembly

·

Parking assist ECU

·

Television camera assembly


Main body ECU (multiplex network body ECU) [Main Body]
Multiplex network door ECU Main body ECU (multiplex network body ECU) -
·

Multiplex network door ECU [Back Door]

·

Main body ECU (multiplex network body ECU) [Main Body]




b.

Details of relevant Data List items (Selected system: Engine and ECT)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine and ECT / Data List.


vi.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383.75 rpm
Actual engine speed -
Coolant Temp Coolant temperature Min.: -40°C (-72°F)
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up -
Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
Engine Speed
Coolant Temp
50003 234 10,9,8


c.

Details of relevant Data List items (Selected system: Engine)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine / Data List.


vi.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
Actual engine speed -
Coolant Temp Engine coolant temperature Min.: -40°C (-72°F)
Max.: 140°C (284°F)
Equivalent to temperature at location of mass air flow meter -
Powertrain > Engine > Data List
Tester Display
Vehicle Speed
Engine Speed
Coolant Temp
50003 61 316,315,309


d.

Details of relevant Data List items (Selected system: Stop and Start)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Stop and Start / Data List.


vi.

According to the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Engine coolant temperature Min.: 16°C (60.8°F)
Max.: 127°C (260.6°F)
75 to 100°C (167 to 212°F): After warming up This is sent from the ECM.
Engine Spd (ECM) Engine speed signal from ECM via CAN communication Min.: 0 rpm
Max.: 12800 rpm
Actual engine speed This is sent from the ECM.
Stop Light SW (ABS/VSC) Stop light switch assembly signal from brake actuator assembly (skid control ECU) via CAN communication OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
This is sent from the brake actuator assembly (skid control ECU).
Vehicle Spd1 (ABS/VSC) Vehicle speed signal from brake actuator assembly (skid control ECU) via CAN communication Min.: 0 km/h (0 mph)
Max.: 327.67 km/h (203.6 mph)
Actual vehicle speed -
Powertrain > Stop and Start > Data List
Tester Display
Coolant Temp
Engine Spd (ECM)
Stop Light SW (ABS/VSC)
Vehicle Spd1 (ABS/VSC)
50003 227 3,57,21,58


e.

Details of relevant Data List items (Selected system: ABS/VSC/TRC)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


vi.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Steering Angle Sensor Steering angle sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: Increases
Turning right: Decreases
-
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Actual engine speed When engine speed is constant: No large fluctuations
Chassis > ABS/VSC/TRAC > Data List
Tester Display
Stop Light SW
Steering Angle Sensor
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle Speed
Engine Revolutions
50003 105 37,26,1,2,3,4,42,16


f.

Details of relevant Data List items (Selected system: Four Wheel Drive)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


vi.

According to the display on the GTS, read the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Steering Angle Value Steering angle value Min.: -3276.8°
Max.: 3276.7°
Turning left: Increases
Turning right: Decreases
-
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (203 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
Engine Coolant Temperature Engine coolant temperature Min.: 0°C (32°F)
Max.: 127.5°C (261.5°F)
Actual engine coolant temperature is displayed -
Chassis > Four Wheel Drive > Data List
Tester Display
Stop Light SW
Steering Angle Value
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Engine Coolant Temperature
50003 118 5,8,1,2,3,4,11


g.

Details of relevant Data List items (Selected system: EMPS)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / EMPS / Data List.


vi.

According to the display on the GTS, read the Data List.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter Min.: 0 km/h (0 mph)
Max.: 300 km/h (186 mph)
Actual vehicle speed -
Engine Revolution Engine speed Min.: 0 rpm
Max.: 12800 rpm
Actual engine speed -
Steering Angle Velocity Steering angle speed Min.: -32768 deg/s
Max.: 32767 deg/s
Left turn: Increases
Right turn: Decreases
-
Chassis > EMPS > Data List
Tester Display
Meter Vehicle Velocity
Engine Revolution
Steering Angle Velocity
50003 142 2,5,8


h.

Details of relevant Data List items (Selected system: Back Door)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Back Door / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Courtesy SW Back door courtesy light switch OFF or ON OFF: Back door closed
ON: Back door open
-
Body Electrical > Back Door > Data List
Tester Display
Courtesy SW
50003 159 4


i.

Details of relevant Data List items (Selected system: Air Conditioner)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly (ambient temperature sensor) Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Engine Coolant Temp Engine coolant temperature sensor Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F)
Actual engine coolant temperature is displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
Engine Coolant Temp
50003 121 2,6


j.

Details of relevant Data List items (Selected system: Combination Meter)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Combination Meter / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed signal Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed When driving at constant speed: No large fluctuations
Engine Rpm Engine speed Min.: 0 rpm
Max.: 12750 rpm
Actual engine speed When engine speed is constant: No large fluctuations
Coolant Temperature Engine coolant temperature Min.: 0°C (32°F)
Max.: 127.5°C (261.5°F)
Actual engine coolant temperature is displayed -
Ambient Temperature Outside temperature Min.: -40°C (-72°F)
Max.: 87.5°C (190 °F)
Almost the same as actual outside temperature The temperature displayed on the multi-information display is -40 to 87.5°C (-72 to 190°F)
Turn Signal Switch (Right) Turn RH signal switch OFF or ON OFF: Turn signal light switch off
ON: Turn signal light switch right
-
Turn Signal Switch (Left) Turn LH signal switch OFF or ON OFF: Turn signal light switch off
ON: Turn signal light switch left
-
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
Engine Rpm
Coolant Temperature
Ambient Temperature
Turn Signal Switch (Right)
Turn Signal Switch (Left)
50003 122 8,9,10,41,98,97


k.

Details of relevant Data List items (Selected system: Blind Spot Monitor Master)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off
-
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (203.62 mph)
Max.: 327.67 km/h (203.61 mph)
Actual vehicle speed -
Steering Angle Steering angle sensor Min.: -3072°
Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Turn Switch State
Vehicle Speed
Steering Angle
50003 313 5,8,9


l.

Details of relevant Data List items (Selected system: Main Body)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Main Body / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly RH signal OFF or ON OFF: Rear door RH closed
ON: Rear door RH open
-
RL Door Courtesy SW Rear door courtesy light switch assembly LH signal OFF or ON OFF: Rear door LH closed
ON: Rear door LH open
-
Back Door Courtesy SW Back door courtesy light switch OFF or ON OFF: Back door closed
ON: Back door open
-
D Seat Buckle SW Driver side seat belt buckle signal OFF or ON OFF: Driver side seat belt unfastened
ON: Driver side seat belt fastened
-
FR Door Courtesy SW Front door courtesy light switch assembly RH signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
-
FL Door Courtesy SW Front door courtesy light switch assembly LH signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
Back Door Courtesy SW
D Seat Buckle SW
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 24,25,26,14,197,199


m.

Details of relevant Data List items (Selected system: Navigation System)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Navigation System / Data List.


vi.

According to the display on the GTS, read the Data List.

Body Electrical > Navigation System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Body Electrical > Navigation System > Data List
Tester Display
Vehicle Speed
50003 212 20


n.

Details of relevant Data List items (Selected system: Radar Cruise2)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Radar Cruise2 / Data List.


vi.

According to the display on the GTS, read the Data List.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vhcl Spd-Brake ECU Vehicle speed Min.: 0.00 k/m, Max.: 327.67 k/m Current value displayed -
Steering Angle Steering sensor signal Min.: -3072.0 deg, Max.: 3070.5 deg Increase: Turning left
Decrease: Turning right
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Vhcl Spd-Brake ECU
Steering Angle
50003 197 24,46


o.

Details of relevant Data List items (Selected system: LKA/LDA)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / LKA/LDA / Data List.


vi.

According to the display on the GTS, read the Data List.

Chassis > LKA/LDA > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Status of turn signal light switch (right) OFF or ON ON: Turn signal light switch right
OFF: Turn signal light switch off
-
Turn Signal Switch (Left) Status of turn signal light switch (left) OFF or ON ON: Turn signal light switch left
OFF: Turn signal light switch off
-
Chassis > LKA/LDA > Data List
Tester Display
Turn Signal Switch (Right)
Turn Signal Switch (Left)
50003 355 4,5