These DTCs are stored when a malfunction occurs in the navigation antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Connection Malfunction(short) | Navigation antenna error | ·
Navigation antenna assembly*1 ·
No. 1 Amplifier Antenna Assembly*2 ·
No. 3 antenna cord sub-assembly*2 ·
No. 2 antenna cord sub-assembly*2 ·
Antenna cord sub-assembly ·
Navigation ECU ·
Antenna divider*3 ·
Harness or connector |
| B15C1 | GPS Antenna Connection Malfunction(break) | Error of the power source to the navigation antenna | ·
Navigation antenna assembly*1 ·
No. 1 Amplifier Antenna Assembly*2 ·
No. 3 antenna cord sub-assembly*2 ·
No. 2 antenna cord sub-assembly*2 ·
Antenna cord sub-assembly ·
Navigation ECU ·
Antenna divider*3 ·
Harness or connector |
*1: Except models with the vehicle identification number on the certification label ending with the character X.
*2: Only for models with the vehicle identification number on the certification label ending with the character X.
*3: w/ Telematics Transceiver
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the navigation antenna assembly is securely connected to the antenna cord sub-assembly.
Navigation antenna assembly is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Telematics Transceiver (Except models with the vehicle identification number on the certification label ending with the character X) | A |
| w/o Telematics Transceiver (Only for models with the vehicle identification number on the certification label ending with the character X) | B |
| w/ Telematics Transceiver | C |
A
B
C
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the antenna connector from the navigation ECU.
Disconnect the antenna connector from the navigation antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 - B-1 | Always | Below 1 Ω |
| A-1a - B-1a | Always | Below 1 Ω |
| A-1 or B-1 - Body ground | Always | 10 kΩ or higher |
| A-1a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation antenna assembly with a known good one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 1 amplifier antenna assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-5 - D-2 | Always | Below 1 Ω |
| C-5a - D-2a | Always | Below 1 Ω |
| C-5 or D-2 - Body ground | Always | 10 kΩ or higher |
| C-5a or D-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-2 - F-1 | Always | Below 1 Ω |
| E-2a - F-1a | Always | Below 1 Ω |
| E-2 or F-1 - Body ground | Always | 10 kΩ or higher |
| E-2a or F-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G-1 - H-1 | Always | Below 1 Ω |
| G-1a - H-1a | Always | Below 1 Ω |
| G-1 or H-1 - Body ground | Always | 10 kΩ or higher |
| G-1a or H-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Instrument Panel Side)>REMOVAL
Replace the No. 1 amplifier antenna assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 amplifier antenna assembly) |
| *b | Front view of wire harness connector
(to wire haenass) |
Disconnect the antenna connector from No. 1 amplifier antenna assembly.
Disconnect the antenna connector from the wire harness.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I-5 - J-1 | Always | Below 1 Ω |
| I-5a - J-1a | Always | Below 1 Ω |
| I-5 or J-1 - Body ground | Always | 10 kΩ or higher |
| I-5a or J-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *a | Front view of wire harness connector
(to Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K-1 - L-6 | Always | Below 1 Ω |
| K-1a - L-6a | Always | Below 1 Ω |
| K-1 or L-6 - Body ground | Always | 10 kΩ or higher |
| K-1a or L-6a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 - 2 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna divider.
| *a | Front view of wire harness connector
(to Antenna Divider) |
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L-2 - K-3 | Always | Below 1 Ω |
| L-2a - K-3a | Always | Below 1 Ω |
| L-2 or K-3 - Body ground | Always | 10 kΩ or higher |
| L-2a or K-3a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to wire harness) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the wire harness.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J-3 - M-2 | Always | Below 1 Ω |
| J-3a - M-2a | Always | Below 1 Ω |
| J-3 or M-2 - Body ground | Always | 10 kΩ or higher |
| J-3a or M-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N-2 - O-1 | Always | Below 1 Ω |
| N-2a - O-1a | Always | Below 1 Ω |
| N-2 or O-1 - Body ground | Always | 10 kΩ or higher |
| N-2a or O-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Navigation ECU) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the navigation ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P-1 - Q-1 | Always | Below 1 Ω |
| P-1a - Q-1a | Always | Below 1 Ω |
| P-1 or Q-1 - Body ground | Always | 10 kΩ or higher |
| P-1a or Q-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Instrument Panel Side)>REMOVAL
Replace the No. 1 amplifier antenna assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna divider with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG