This sensor detects the rotation speed of the turbine which indicates the input speed of the transaxle. By comparing the input turbine speed (speed sensor NT) signal with the counter gear speed (speed sensor NC) signal, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0717 | Input Speed Sensor Circuit No Signal | All conditions are met for 5 sec. or more (1-trip detection logic):
(a) Gear change is not performed. (b) Gear position is 2nd, 3rd, 4th, 5th or 6th. (c) Transmission input shaft speed is less than 300 rpm. (d) Transmission output shaft speed is 1000 rpm or more. (e) Park/neutral position switch NSW and R input signals are OFF. |
·
Speed sensor NT (transmission revolution sensor) ·
Transmission wire ·
Wiring harness connector ·
ECM |
Comes on | DTC stored |
| P07BF | Input/Turbine Speed Sensor "A" Circuit Low | The speed sensor input voltage is below 0.1 V for 4.5 sec. or more (1-trip detection logic). | ·
Speed sensor NT (transmission revolution sensor) ·
Transmission wire ·
Wiring harness connector ·
ECM |
Comes on | DTC stored |
| P07C0 | Input/Turbine Speed Sensor "A" Circuit High | The speed sensor input voltage is higher than 1.9 V for 4.5 sec. or more (1-trip detection logic). | ·
Speed sensor NT (transmission revolution sensor) ·
Transmission wire ·
Wiring harness connector ·
ECM |
Comes on | DTC stored |
The NT terminal of the ECM detects a pulse signal from speed sensor NT (input RPM). The ECM calculates gear shifts by comparing the signal from speed sensor NT with the signal from speed sensor NC.
While the transaxle is operating in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: A pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NT) | Input turbine speed (speed sensor NT) | Min.: 0 rpm
Max.: 12750 rpm |
·
Lock-up on (after warming up the engine): Value from speed sensor NT equal to engine speed ·
Lock-up off (idling with shift lever in N): Value from speed sensor NT nearly equal to engine speed |
The data is displayed in increments of 50 rpm. |
| NT Sensor Voltage | Speed sensor NT output voltage | Min.: 0 V
Max.: 5 V |
0.1 to 1.9 V: Engine idling | - |
| Tester Display |
|---|
| SPD (NT) |
| NT Sensor Voltage |
SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.
SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
Remove the transmission valve body assembly.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL
Make sure that the connector is properly connected, and check the transmission revolution sensor installation.
The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Transmission Wire |
| *a | Transmission Revolution Sensor Side |
| *b | Wiring Harness Connector Side |
Disconnect the transmission revolution sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| NTB transmission revolution sensor side - A-1 (NTB) wiring harness connector side | Always | Below 1 Ω |
| NTO transmission revolution sensor side - A-2 (NTO) wiring harness connector side | Always | Below 1 Ω |
| NTB transmission revolution sensor side or A-1 (NTB) wiring harness connector side - Body ground and other terminals | Always | 10 kΩ or higher |
| NTO transmission revolution sensor side or A-2 (NTO) wiring harness connector side - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B78 wiring harness connector.
Disconnect the B77 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B78-1 (NTB) - B77-116 (NTB) | Always | Below 1 Ω |
| B78-2 (NTO) - B77-115 (NTO) | Always | Below 1 Ω |
| B78-1 (NTB) or B77-116 (NTB) - Body ground and other terminals | Always | 10 kΩ or higher |
| B78-2 (NTO) or B77-115 (NTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the wiring harness connector.
| *1 | Wiring Harness Connector | - | - |
| *a | Transmission Wire Side | *b | ECM Side |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (NTB) - B78-1 (NTB) | Always | Below 1 Ω |
| A-2 (NTO) - B78-2 (NTO) | Always | Below 1 Ω |
| A-1 (NTB) - All other terminals except B78-1 (NTB) | Always | 10 kΩ or higher |
| A-2 (NTO) - All other terminals except B78-2 (NTO) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transmission revolution sensor.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Clear the DTCs.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Write down the currently output DTCs before clearing them.
Perform the monitor drive pattern.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>MONITOR DRIVE PATTERN
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only P0717, P07BF or P07C0 is output | A |
| DTCs are not output | B |
A
B