The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Telephone microphone signal is lost. | ·
Navigation receiver assembly ·
Map light assembly ·
Telephone microphone assembly ·
Harness or connector |
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the G139 navigation receiver assembly connector.
Disconnect the Q16 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G139-4 (MACC) - Q16-3 (MACC) | Always | Below 1 Ω |
| G139-5 (MIN+) - Q16-4 (MCO+) | Always | Below 1 Ω |
| G139-19 (MIN-) - Q16-6 (MCO-) | Always | Below 1 Ω |
| G139-6 (SNS2) - Q16-5 (SNS2) | Always | Below 1 Ω |
| G139-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| G139-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| G139-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| G139-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| G139-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-4 (MCO+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-5 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| A-6 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-3 (MACC) - A-4 (MCO+) | Always | 10 kΩ or higher |
| A-3 (MACC) - A-5 (SNS2) | Always | 10 kΩ or higher |
| A-3 (MACC) - A-6 (MCO-) | Always | 10 kΩ or higher |
| A-4 (MCO+) - A-5 (SNS2) | Always | 10 kΩ or higher |
| A-4 (MCO+) - A-6 (MCO-) | Always | 10 kΩ or higher |
| A-5 (SNS2) - A-6 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG