Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the navigation receiver assembly.

It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E355986E01
0.625,3.271 2.083,3.521 1.458,0.25 10 false Map Light Assembly 0.615,3.094 1.073,3.292 0.458,0.198 10 false Q16 0.625,2.354 2,2.75 1.375,0.396 10 false Telephone Microphone Assembly 1.188,2.021 1.802,2.219 0.615,0.198 10 false SNS2 5.656,2.021 6.271,2.219 0.615,0.198 10 false SNS2 3.177,1.75 3.792,1.948 0.615,0.198 10 false Shielded 4.354,1.75 4.969,1.948 0.615,0.198 10 false Shielded 1.844,1.906 2.458,2.104 0.615,0.198 10 false SNS2 5.677,1.625 6.292,1.823 0.615,0.198 10 false SGND 5.677,1.25 6.292,1.448 0.615,0.198 10 false MIN- 5.646,0.844 6.26,1.042 0.615,0.198 10 false MIN+ 5.698,0.448 6.313,0.646 0.615,0.198 10 false MACC 1.156,0.448 1.771,0.646 0.615,0.198 10 false MACC 1.802,0.74 2.417,0.938 0.615,0.198 10 false MCO+ 1.823,1.125 2.438,1.323 0.615,0.198 10 false MCO- 1.25,1.219 1.865,1.417 0.615,0.198 10 false MIC- 1.229,0.833 1.844,1.031 0.615,0.198 10 false MIC+ 1.792,0.323 2.406,0.521 0.615,0.198 10 false MACC 1.635,0.333 1.792,0.531 0.156,0.198 10 false 5 5.552,2.573 6.771,2.958 1.219,0.385 10 false Navigation Receiver Assembly 5.542,2.406 6,2.604 0.458,0.198 10 false G139 1.646,0.75 1.802,0.948 0.156,0.198 10 false 3 1.656,1.135 1.813,1.333 0.156,0.198 10 false 2 1.656,1.927 1.813,2.125 0.156,0.198 10 false 1 2.313,1.917 2.469,2.115 0.156,0.198 10 false 5 2.333,1.125 2.49,1.323 0.156,0.198 10 false 6 2.313,0.313 2.469,0.51 0.156,0.198 10 false 3 2.323,0.729 2.479,0.927 0.156,0.198 10 false 4 5.396,1.51 5.604,1.719 0.208,0.208 10 false 18 5.458,0.333 5.667,0.542 0.208,0.208 10 false 4 5.458,0.74 5.667,0.948 0.208,0.208 10 false 5 5.396,1.135 5.604,1.344 0.208,0.208 10 false 19 5.458,1.917 5.667,2.125 0.208,0.208 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G139 navigation receiver assembly connector.


b.

Disconnect the Q16 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-4 (MACC) - Q16-3 (MACC) Always Below 1 Ω
G139-5 (MIN+) - Q16-4 (MCO+) Always Below 1 Ω
G139-19 (MIN-) - Q16-6 (MCO-) Always Below 1 Ω
G139-6 (SNS2) - Q16-5 (SNS2) Always Below 1 Ω
G139-4 (MACC) - Body ground Always 10 kΩ or higher
G139-5 (MIN+) - Body ground Always 10 kΩ or higher
G139-19 (MIN-) - Body ground Always 10 kΩ or higher
G139-18 (SGND) - Body ground Always 10 kΩ or higher
G139-6 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


c.
E355981C02
0.354,2.49 0.719,2.76 0.365,0.271 0.188,0.99 0.552,1.26 0.365,0.271 2.125,1.031 2.51,0.406 2.51,0.406 2.677,0.406 true 1.646,1.031 1.292,0.406 1.292,0.406 1.156,0.406 true 2.24,2.688 2.458,2.052 2.458,2.052 2.625,2.052 true 1.729,2.708 1.844,1.833 1.844,1.833 2.01,1.833 true 1.469,2.688 1.344,1.833 1.344,1.833 1.208,1.833 true 1.802,1.042 1.406,0.156 1.406,0.156 1.271,0.156 true 1.208,2.677 1.115,2.052 1.115,2.052 0.979,2.052 true 1.969,1.042 2.323,0.177 2.323,0.177 2.49,0.177 true 0.156,0.083 0.469,0.281 0.313,0.198 10 false *a 0.323,1.042 0.479,1.24 0.156,0.198 10 false A 0.49,2.542 0.646,2.74 0.156,0.198 10 false B 2.74,0.344 3.354,0.542 0.615,0.198 10 false MACC 0.885,0.073 1.5,0.271 0.615,0.198 10 false SNS2 0.729,0.302 1.344,0.5 0.615,0.198 10 false MCO- 2.688,1.979 3.302,2.177 0.615,0.198 10 false MACC 2.073,1.75 2.688,1.948 0.615,0.198 10 false MIC+ 0.875,1.74 1.49,1.938 0.615,0.198 10 false MIC- 0.552,1.979 1.167,2.177 0.615,0.198 10 false SNS2 2.531,0.104 3.146,0.302 0.615,0.198 10 false MCO+
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (MACC) - B-5 (MACC) Always Below 1 Ω
A-4 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-6 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-3 (MACC) - A-4 (MCO+) Always 10 kΩ or higher
A-3 (MACC) - A-5 (SNS2) Always 10 kΩ or higher
A-3 (MACC) - A-6 (MCO-) Always 10 kΩ or higher
A-4 (MCO+) - A-5 (SNS2) Always 10 kΩ or higher
A-4 (MCO+) - A-6 (MCO-) Always 10 kΩ or higher
A-5 (SNS2) - A-6 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG