Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The parking assist ECU and radio and display receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D8 Monitor Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

AVC-LAN circuit

·

Parking assist ECU

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E353835E01
5.438,2.854 6.635,3.49 1.198,0.635 10 false Radio and Display Receiver Assembly 3.271,3.979 4.594,4.26 1.323,0.281 10 false Parking Assist ECU 0.563,4.458 2.875,4.792 2.313,0.333 10 false : AVC-LAN Communication Line 0.469,2.865 1.792,3.146 1.323,0.281 10 false from ACC Relay 0.219,1.917 1.542,2.198 1.323,0.281 10 false from IG1 NO.1 Relay 0.74,0.875 2.063,1.156 1.323,0.281 10 false from Battery 2.042,1.073 3.365,1.354 1.323,0.281 10 false ECU-B NO.1 2.073,2.052 3.396,2.333 1.323,0.281 10 false ECU-IG NO.2 2.271,3.042 2.729,3.313 0.458,0.271 10 false ACC 3.458,0.865 3.917,1.135 0.458,0.271 10 false +B 3.458,1.875 3.917,2.146 0.458,0.271 10 false IG 3.458,2.875 3.917,3.146 0.458,0.271 10 false ACC 3.49,3.375 3.948,3.646 0.458,0.271 10 false GND1 4.021,1.26 4.479,1.531 0.458,0.271 10 false TX+ 3.99,1.625 4.448,1.896 0.458,0.271 10 false TX- 5.521,1.635 5.979,1.906 0.458,0.271 10 false TX3- 5.5,1.26 5.958,1.531 0.458,0.271 10 false TX3+ 5.417,2.646 5.875,2.917 0.458,0.271 10 false G159 3.302,3.729 3.76,4 0.458,0.271 10 false a2 5.323,1.135 5.781,1.406 0.458,0.271 10 false 7 5.323,1.49 5.781,1.76 0.458,0.271 10 false 8 4.438,1.51 4.896,1.781 0.458,0.271 10 false 9 4.417,1.135 4.875,1.406 0.458,0.271 10 false 10 3.156,0.781 3.615,1.052 0.458,0.271 10 false 2 3.177,1.75 3.635,2.021 0.458,0.271 10 false 6 3.26,2.75 3.719,3.021 0.458,0.271 10 false 1 3.219,3.24 3.677,3.51 0.458,0.271 10 false 3 0.198,0.365 1.604,0.729 1.406,0.365 10 false from Engine Stop and Start ECU 0.177,1.385 1.583,1.75 1.406,0.365 10 false from Engine Stop and Start ECU 0.167,2.323 1.573,2.688 1.406,0.365 10 false from Engine Stop and Start ECU 1.854,0.313 2.313,0.583 0.458,0.271 10 false *1 1.813,1.354 2.271,1.625 0.458,0.271 10 false *1 1.813,2.323 2.271,2.594 0.458,0.271 10 false *1 1.844,0.76 2.302,1.031 0.458,0.271 10 false *2 1.813,1.813 2.271,2.083 0.458,0.271 10 false *2 1.813,2.76 2.271,3.031 0.458,0.271 10 false *2 0.167,3.771 2.115,4.052 1.948,0.281 10 false *1: w/ Stop and Start System 0.167,4.063 2.115,4.344 1.948,0.281 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
E297790E01
1.438,0.208 1.896,0.49 0.458,0.281 2.177,0.969 2.688,0.604 true 1.667,1.792 1.219,1.021 true 0.885,0.979 0.604,0.979 true 1,1.167 0.99,1.76 true 0.198,0.083 0.51,0.24 0.313,0.156 10 false *a 0.26,0.896 0.573,1.052 0.313,0.156 10 false ACC 1.708,1.76 2.021,1.917 0.313,0.156 10 false +B 2.76,0.542 3.26,0.708 0.5,0.167 10 false GND1 0.865,1.771 1.365,1.938 0.5,0.167 10 false IG 1.583,0.271 1.896,0.469 0.313,0.198 10 false a2

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-3 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a2-2 (+B) - a2-3 (GND1) Always 11 to 14 V*1
10.5 to 16 V*2
a2-6 (IG) - a2-3 (GND1) Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
a2-1 (ACC) - a2-3 (GND1) Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E333570E01
1.656,1.01 1.906,0.417 1.906,0.417 2.052,0.417 false 1.521,1.01 1.333,0.406 1.333,0.406 1.208,0.406 false 0.865,0.333 1.229,0.521 0.365,0.188 10 false TX3- 2.104,0.344 2.448,0.51 0.344,0.167 10 false TX3+

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX3+) - 8 (TX3-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the G159 radio and display receiver assembly connector.


b.

Disconnect the a2 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-7 (TX3+) - a2-10 (TX+) Always Below 1 Ω
G159-8 (TX3-) - a2-9 (TX-) Always Below 1 Ω
G159-7 (TX3+) - Body ground Always 10 kΩ or higher
G159-8 (TX3-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU
a.

Replace the parking assist ECU with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (PARKING ASSIST ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY