There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 16 (BAT) of the DLC3.
| Detection Item | Trouble Area |
|---|---|
|
*1: w/ Entry and Start System *2: for 4WD/AWD *3: w/ Stop and Start System |
|
| No resistance exists between terminal 18 (CA4H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU and terminal 16 (BAT) of the DLC3. | ·
Short to +B in bus 2 CAN main wires ·
Short to +B in bus 2 CAN branch wires ·
ECM ·
Combination meter assembly ·
Central gateway ECU ·
Power steering ECU assembly ·
Air conditioning amplifier assembly ·
Airbag sensor assembly ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Certification ECU (smart key ECU assembly)*1 ·
4WD ECU assembly*2 ·
Brake actuator assembly (skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
Engine stop and start ECU*3 ·
No. 11 CAN junction connector ·
No. 12 CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
| *a | Rear view of wire harness connector
(to No. 11 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to Air Conditioning Amplifier Assembly |
| *e | to Brake Actuator Assembly (Skid Control ECU) | *f | to No. 12 CAN Junction Connector |
| *g | to Engine Stop and Start ECU (w/ Stop and Start System) | *h | to Airbag Sensor Assembly |
| *i | to ECM | - | - |
Disconnect the No. 11 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*: w/ Stop and Start System |
|||
| G188-1 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (multiplex network body ECU) |
| G188-12 (CANL) - G14-16 (BAT) | |||
| G188-2 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| G188-13 (CANL) - G14-16 (BAT) | |||
| G188-3 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Brake actuator assembly (skid control ECU) |
| G188-14 (CANL) - G14-16 (BAT) | |||
| G188-4 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 12 CAN junction connector |
| G188-15 (CANL) - G14-16 (BAT) | |||
| G188-5 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Engine stop and start ECU* |
| G188-16 (CANL) - G14-16 (BAT) | |||
| G188-6 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Airbag sensor assembly |
| G188-17 (CANL) - G14-16 (BAT) | |||
| G188-7 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| G188-18 (CANL) - G14-16 (BAT) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 12 CAN junction connector CAN main wire) | B |
| NG (ECU or sensor CAN main or branch wires) | C |
A
B
C
Reconnect the G188 No. 11 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 12 CAN junction connector.
| *a | Rear view of wire harness connector
(to No. 12 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Combination Meter Assembly | *d | to Power Steering ECU Assembly |
| *e | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) | *f | to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) |
| *g | to 4WD ECU Assembly (for 4WD/AWD) | *h | to No. 11 CAN Junction Connector |
| *i | to Central Gateway ECU | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Entry and Start System *2: for 4WD/AWD |
|||
| G189-1 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| G189-12 (CANL) - G14-16 (BAT) | |||
| G189-2 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power steering ECU assembly |
| G189-13 (CANL) - G14-16 (BAT) | |||
| G189-4 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| G189-15 (CANL) - G14-16 (BAT) | |||
| G189-5 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Certification ECU (smart key ECU assembly)*1 |
| G189-16 (CANL) - G14-16 (BAT) | |||
| G189-6 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | 4WD ECU assembly*2 |
| G189-17 (CANL) - G14-16 (BAT) | |||
| G189-8 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 11 CAN junction connector |
| G189-19 (CANL) - G14-16 (BAT) | |||
| G189-10 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU |
| G189-21 (CANL) - G14-16 (BAT) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 11 CAN junction connector CAN main wire) | B |
| NG (Central gateway ECU CAN branch wire) | C |
| NG (ECU or sensor CAN main or branch wires) | D |
A
B
C
D
Reconnect the G189 No. 12 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU) |
| *b | Front view of DLC3 |
Disconnect the central gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G170-18 (CA4H) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G170-17 (CA4L) - G14-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU) |
| *b | Front view of DLC3 |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G170-18 (CA4H) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G170-17 (CA4L) - G14-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG