Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System) › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B1633  Curtain Shield Airbag Sensor Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit consists of the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.

The No. 2 side airbag sensor assembly RH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.

DTC B1633 is stored when a malfunction is detected in the circuit for the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1633 Curtain Shield Airbag Sensor Initialization Error (RH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A No. 2 side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C401868E28
5.375,2.083 6.99,2.365 1.615,0.281 10 false Airbag Sensor Assembly 5.375,1.927 6.208,2.125 0.833,0.198 10 false M15 5.677,0.875 6.51,1.073 0.833,0.198 10 false BBR+ 5.698,1.458 6.531,1.656 0.833,0.198 10 false BBR- 5.406,0.76 6.24,0.958 0.833,0.198 10 false 25 5.406,1.365 6.24,1.563 0.833,0.198 10 false 26 1.615,0.75 2.448,0.948 0.833,0.198 10 false 4 1.635,1.313 2.469,1.51 0.833,0.198 10 false 3 1.146,0.854 1.979,1.052 0.833,0.198 10 false BCR+ 1.104,1.469 1.938,1.667 0.833,0.198 10 false BCR- 1.135,2.792 1.969,2.99 0.833,0.198 10 false BDR+ 1.146,3.333 1.979,3.531 0.833,0.198 10 false BDR- 1.604,2.688 2.438,2.885 0.833,0.198 10 false 1 1.594,3.24 2.427,3.438 0.833,0.198 10 false 2 4.083,2.813 4.917,3.01 0.833,0.198 10 false BDR+ 4.094,3.354 4.927,3.552 0.833,0.198 10 false BDR- 0.552,3.969 2.167,4.375 1.615,0.406 10 false No. 2 Side Airbag Sensor Assembly RH 0.552,3.813 1.313,4.146 0.76,0.333 10 false M16 4.01,3.979 6.052,4.25 2.042,0.271 10 false Side Airbag Pressure Sensor RH 4.021,3.823 4.781,4.156 0.76,0.333 10 false I10 2.698,3.344 3.458,3.677 0.76,0.333 10 false IM2 2.708,2.813 3.469,3.146 0.76,0.333 10 false IM2 2.781,3.167 3.615,3.365 0.833,0.198 10 false 2 2.781,2.594 3.615,2.792 0.833,0.198 10 false 1 2.667,2.99 3.5,3.188 0.833,0.198 10 false BDR+ 2.708,3.552 3.542,3.75 0.833,0.198 10 false BDR- 3.906,2.708 4.74,2.906 0.833,0.198 10 false 2 3.906,3.219 4.74,3.417 0.833,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK PAST DTC
a.

Turn the power switch on (IG), and wait for at least 60 seconds.



Result:
Proceed to
DTC B1632 is not output
DTC B1632 is output



DTC B1632 is not output

2.CHECK CONNECTION OF CONNECTORS

DTC B1632 is output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and No. 2 side airbag sensor assembly RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and No. 2 side airbag sensor assembly RH.


b.
C208245C47
0.656,1.75 0.969,1.948 0.313,0.198 10 false *1 1.521,1.031 1.833,1.229 0.313,0.198 10 false *3 2.573,1.542 2.885,1.74 0.313,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and No. 2 side airbag sensor assembly RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE
a.
C411569C01
0.698,0.594 1.156,0.813 0.458,0.219 2.646,3.115 3.104,3.333 0.458,0.219 1.333,3.792 1.49,3.792 1.49,3.792 1.781,3.854 true 1.385,3.427 1.542,3.427 1.542,3.427 1.875,3.854 true 1.458,1.24 1.615,1.24 1.615,1.24 1.885,0.771 true 2.458,1.208 2.281,1.208 2.281,1.208 2.063,0.76 true 1.885,4.26 2.021,4.396 2.021,4.396 2.177,4.396 true 0.427,2.677 0.74,2.833 0.313,0.156 10 false *1 2.688,2.479 3,2.635 0.313,0.156 10 false *2 1.5,2.385 1.813,2.542 0.313,0.156 10 false *3 2.229,4.302 2.542,4.458 0.313,0.156 10 false *4 0.771,0.208 1.083,0.365 0.313,0.156 10 false *a 0.958,2.906 1.271,3.063 0.313,0.156 10 false *b 2.281,2.167 2.594,2.323 0.313,0.156 10 false A 1.99,2.167 2.302,2.323 0.313,0.156 10 false B 1.01,2.177 1.323,2.333 0.313,0.156 10 false C 0.719,2.177 1.031,2.333 0.313,0.156 10 false D 0.792,0.625 1.104,0.781 0.313,0.156 10 false M16 2.74,3.135 3.052,3.292 0.313,0.156 10 false M15 0.917,3.698 1.417,3.938 0.5,0.24 10 false BBR+ 1,3.333 1.5,3.573 0.5,0.24 10 false BBR- 2.531,1.125 3.031,1.365 0.5,0.24 10 false BCR+ 1.073,1.135 1.573,1.375 0.5,0.24 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M16-4 (BCR+) - Body ground Power switch on (IG) Below 1 V
M16-3 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M16-4 (BCR+) - M16-3 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M16-4 (BCR+) - M16-3 (BCR-) Always 1 MΩ or higher
M16-4 (BCR+) - Body ground Always 1 MΩ or higher
M16-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C374693C24
0.969,1.583 1.24,1.781 0.271,0.198 10 false *1 2.49,1.396 2.76,1.594 0.271,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633 is output
DTC B1638 is output
DTCs B1633 and B1638 are not output


HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B1633 is output

6.CHECK CONNECTION OF CONNECTOR

DTC B1638 is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

DTCs B1633 and B1638 are not output

6.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the side airbag pressure sensor RH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

7.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

7.CHECK CONNECTOR
a.
C306644C18
0.604,1.5 0.917,1.656 0.313,0.156 10 false *1 2.604,1.5 2.917,1.656 0.313,0.156 10 false *2 1.417,1.25 1.729,1.406 0.313,0.156 10 false *3 1.854,1.25 2.167,1.406 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the connectors from the side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.


b.

Check that the connector (on the side airbag pressure sensor RH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

8.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT

The connector is deformed or damaged

REPLACE FRONT DOOR WIRE RH

8.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT
a.
C411574C01
0.74,0.813 1.24,1.052 0.5,0.24 2.24,2.906 2.74,3.146 0.5,0.24 1.271,1.542 1.438,1.542 1.438,1.542 1.677,1.01 true 2.51,1.531 2.333,1.531 2.333,1.531 2.021,1 true 0.979,3.375 1.146,3.375 1.146,3.375 1.625,3.698 true 1.365,2.99 1.531,2.99 1.531,2.99 1.813,3.677 true 1.917,4.198 2.135,4.344 2.135,4.344 2.292,4.344 true 0.448,2.583 0.76,2.74 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.229,2.302 1.542,2.458 0.313,0.156 10 false *3 1.792,2.333 2.104,2.49 0.313,0.156 10 false *4 0.781,0.292 1.094,0.448 0.313,0.156 10 false *a 0.531,2.927 0.844,3.083 0.313,0.156 10 false *b 0.896,0.844 1.208,1 0.313,0.156 10 false I10 2.396,2.125 2.708,2.281 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.625,2.125 1.938,2.281 0.313,0.156 10 false C 1.469,2.115 1.781,2.271 0.313,0.156 10 false D 1.031,2.115 1.344,2.271 0.313,0.156 10 false E 0.708,2.125 1.021,2.281 0.313,0.156 10 false F 2.365,2.948 2.677,3.104 0.313,0.156 10 false M16 2.583,1.438 3.146,1.698 0.563,0.26 10 false BDR+ 0.854,1.448 1.417,1.708 0.563,0.26 10 false BDR- 0.969,2.896 1.531,3.156 0.563,0.26 10 false BDR- 0.51,3.292 1.073,3.552 0.563,0.26 10 false BDR+ 2.375,4.26 2.688,4.417 0.313,0.156 10 false *5
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I10-2 (BDR+) - Body ground power switch on (IG) Below 1 V
I10-1 (BDR-) - Body ground power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always 1 MΩ or higher
I10-2 (BDR+) - Body ground Always 1 MΩ or higher
I10-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.CHECK CONNECTORS
9.CHECK DTC
a.
C238395C22
0.729,1.563 1,1.74 0.271,0.177 10 false *1 2.583,1.542 2.896,1.75 0.313,0.208 10 false *2
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH


Connect the connectors to the side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633 is output
DTC B1633 is not output


HINT:

Codes other than DTC B1633 may be output at this time, but they are not related to this check.




DTC B1633 is output

DTC B1633 is not output

10.CHECK CONNECTORS
a.
B510595C02
0.458,1.479 0.771,1.635 0.313,0.156 10 false *1 2.823,1.5 3.135,1.656 0.313,0.156 10 false *2 1.25,1.229 1.563,1.385 0.313,0.156 10 false *3 2.021,1.24 2.333,1.396 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire RH.


b.

Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

11.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

11.CHECK FLOOR WIRE
a.
C411586C09
0.583,3.5 0.99,3.75 0.406,0.25 0.969,0.854 1.292,1.094 0.323,0.24 1.646,0.51 1.844,0.51 1.844,0.51 2.104,0.719 true 1.854,3.052 1.729,3.052 1.729,3.052 1.646,3.573 true 2.521,3.063 2.396,3.063 2.396,3.063 1.813,3.594 true 2.115,4.354 2,4.354 2,4.354 1.854,4.115 true 2.896,1.094 2.781,1.094 2.781,1.094 2.281,0.76 true 0.167,0.177 0.479,0.385 0.313,0.208 10 false *a 1.021,0.896 1.333,1.104 0.313,0.208 10 false IM2 2.563,2.26 2.781,2.479 0.219,0.219 10 false A 2.24,2.271 2.458,2.49 0.219,0.219 10 false B 1.792,2.271 2.01,2.49 0.219,0.219 10 false C 1.479,2.271 1.698,2.49 0.219,0.219 10 false D 1.031,2.271 1.25,2.49 0.219,0.219 10 false E 0.719,2.271 0.938,2.49 0.219,0.219 10 false F 0.385,2.719 0.698,2.927 0.313,0.208 10 false *1 1.229,2.479 1.542,2.688 0.313,0.208 10 false *3 2.771,2.708 3.083,2.917 0.313,0.208 10 false *2 1.99,2.458 2.302,2.667 0.313,0.208 10 false *4 0.542,3.031 0.854,3.24 0.313,0.208 10 false *b 0.656,3.542 0.969,3.75 0.313,0.208 10 false M16 2.948,1 3.365,1.313 0.417,0.313 10 false BDR+ 1.292,0.417 1.688,0.615 0.396,0.198 10 false BDR- 1.875,2.979 2.385,3.188 0.51,0.208 10 false BDR+ 2.542,2.979 3.052,3.188 0.51,0.208 10 false BDR- 2.156,4.271 2.469,4.479 0.313,0.208 10 false *5
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM2-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
IM2-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always 1 MΩ or higher
IM2-1 (BDR+) - Body ground Always 1 MΩ or higher
IM2-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE