Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0371435 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Airbag sensor assembly
·

Clear the zero point calibration data

·

Deceleration sensor zero point calibration


Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


for K120, K120F:
·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


·

for K120:

(Click here)

·

for K120F:

(Click here)


·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
for GF1A:

Reset memory


Dynamic torque control 4WD/AWD system (Click here)
for GF2A:

ECU data initialization


Dynamic torque vectoring AWD system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Airbag sensor assembly
·

Clear zero point calibration data

·

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58810J 6.REMOVE CONSOLE BOX ASSEMBLY

Hide 89170 8.REMOVE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal of the battery, the airbag may deploy even if an impact is applied only to the airbag sensor assembly. Therefore, make sure that the negative (-) auxiliary battery terminal of the battery is disconnected before performing this procedure.




c.
B525308C01
0,0 0,0 false
V113147

Push the Connector Lock
V113148

Pull Out the Lock Lever


Pull out each connector with its connector lock pushed to disconnect the 3 connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.
B525307

Remove the 3 bolts and airbag sensor assembly.

NOTICE:

If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the airbag sensor assembly with a new one.