Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B163B  Side Airbag Sensor Assembly No.2 Lost Communication (LH)  B163C  Side Airbag Sensor Assembly No.2 Initialization Error (LH)  


DESCRIPTION

The side collision sensor LH circuit consists of the airbag sensor assembly and floor side airbag sensor LH.

The floor side airbag sensor LH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the No. 2 side collision sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B163B Side Airbag Sensor Assembly No.2 Lost Communication (LH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

A floor side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Floor side airbag sensor LH

·

Airbag sensor assembly


Comes on Not applicable
B163C Side Airbag Sensor Assembly No.2 Initialization Error (LH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

A floor side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Floor side airbag sensor LH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C370759E33
1.24,2.094 1.698,2.25 0.458,0.156 10 false BFL- 1.24,0.927 1.698,1.083 0.458,0.156 10 false BFL+ 1.75,0.802 1.958,0.979 0.208,0.177 10 false 2 1.719,2 1.927,2.146 0.208,0.146 10 false 1 0.323,2.802 0.646,2.99 0.323,0.188 10 false N23 0.323,2.958 2.208,3.229 1.885,0.271 10 false Floor Side Airbag Sensor LH 5.323,0.823 5.615,1.01 0.292,0.188 10 false 29 5.333,1.969 5.583,2.156 0.25,0.188 10 false 30 5.615,0.917 6.115,1.083 0.5,0.167 10 false BCL+ 5.615,2.083 6.104,2.26 0.49,0.177 10 false BCL- 5.49,2.781 5.771,2.969 0.281,0.188 10 false N21 5.49,2.938 7.156,3.302 1.667,0.365 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and floor side airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and floor side airbag sensor LH.


b.
C208244C33
2.594,1.781 2.906,1.979 0.313,0.198 10 false *2 0.646,1.344 0.958,1.542 0.313,0.198 10 false *1 1.521,0.604 1.833,0.802 0.313,0.198 10 false *3
*1 Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and floor side airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
C411588C01
0.74,3.698 1.219,3.948 0.479,0.25 0.74,0.76 1.219,1.01 0.479,0.25 1.125,1.417 1.292,1.417 1.292,1.417 1.656,0.969 true 2.563,1.417 2.385,1.417 2.385,1.417 2.01,0.969 true 2.594,3.906 2.417,3.906 2.417,3.906 1.99,4.021 true 2.563,3.583 2.385,3.583 2.385,3.583 1.885,3.969 true 2.365,4.458 2.188,4.458 2.188,4.458 2.083,4.354 true 0.469,2.542 0.781,2.698 0.313,0.156 10 false *1 2.802,2.875 3.115,3.031 0.313,0.156 10 false *2 1.552,2.25 1.865,2.406 0.313,0.156 10 false *3 2.406,4.344 2.719,4.5 0.313,0.156 10 false *4 0.781,0.292 1.094,0.448 0.313,0.156 10 false *a 0.708,3.167 1.021,3.323 0.313,0.156 10 false *b 2.656,3.833 3.052,4 0.396,0.167 10 false BCL- 2.615,3.51 3.01,3.677 0.396,0.167 10 false BCL+ 2.635,1.323 3.031,1.49 0.396,0.167 10 false BFL+ 0.76,1.313 1.156,1.479 0.396,0.167 10 false BFL- 0.854,0.802 1.25,0.969 0.396,0.167 10 false N23 0.854,3.74 1.25,3.906 0.396,0.167 10 false N21 2.385,2.021 2.781,2.188 0.396,0.167 10 false A 2.063,2.021 2.458,2.188 0.396,0.167 10 false B 1.021,2.031 1.417,2.198 0.396,0.167 10 false C 0.719,2.042 1.115,2.208 0.396,0.167 10 false D
*1 Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N23-2 (BFL+) - Body ground Power switch on (IG) Below 1 V
N23-1 (BFL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (BCL+) and 30 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N23-2 (BFL+) - N23-1 (BFL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N23-2 (BFL+) - N23-1 (BFL-) Always 1 MΩ or higher
N23-2 (BFL+) - Body ground Always 1 MΩ or higher
N23-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR SIDE AIRBAG SENSOR LH
a.

Connect the connectors to the airbag sensor assembly.


b.
C370762C20
0.875,0.938 1.188,1.135 0.313,0.198 10 false *1 2.406,1.313 2.719,1.51 0.313,0.198 10 false *2
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Interchange the floor side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B163B or B163C is output
DTC B162B or B162C is output
DTCs B162B, B162C, B163B and B163C are not output


HINT:

Codes other than DTC B162B, B162C, B163B and B163C may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the floor side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B163B or B163C is output

DTC B162B or B162C is output

DTCs B162B, B162C, B163B and B163C are not output