The driver side knee squib circuit consists of the airbag sensor assembly and lower No. 1 instrument panel airbag assembly.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B1860 | Short in Knee Airbag (D Side) Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the driver side knee squib circuit during the primary check. ·
A lower No. 1 instrument panel airbag assembly malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Lower No. 1 instrument panel airbag assembly ·
Airbag sensor assembly |
Comes on | Applicable |
| B1861 | Open in Knee Airbag (D Side) Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the driver side knee squib circuit for 2 seconds. ·
A lower No. 1 instrument panel airbag assembly malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Lower No. 1 instrument panel airbag assembly ·
Airbag sensor assembly |
Comes on | Applicable |
| B1862 | Short in Knee Airbag (D Side) Squib Circuit (to Ground) | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the driver side knee squib circuit for 0.5 seconds. ·
A lower No. 1 instrument panel airbag assembly malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Lower No. 1 instrument panel airbag assembly ·
Airbag sensor assembly |
Comes on | Applicable |
| B1863 | Short in Knee Airbag (D Side) Squib Circuit (to +B) | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the driver side knee squib circuit for 0.5 seconds. ·
A lower No. 1 instrument panel airbag assembly malfunction. ·
An airbag sensor assembly malfunction. |
·
Instrument panel wire ·
Lower No. 1 instrument panel airbag assembly ·
Airbag sensor assembly |
Comes on | Applicable |
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | SST |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
Connect the connector to the airbag sensor assembly.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the lower No. 1 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTCs B1860, B1861, B1862 and B1863 are not output |
| DTC B1860, B1861, B1862 or B1863 is output |
Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
DTCs B1860, B1861, B1862 and B1863 are not output
DTC B1860, B1861, B1862 or B1863 is output
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
|
Release the activation prevention mechanism |
Disconnect the instrument panel wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G107-1 (DK+) - Body ground | Power switch on (IG) | Below 1 V |
| G107-2 (DK-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G107-1 (DK+) - G107-2 (DK-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G107-1 (DK+) - Body ground | Always | 1 MΩ or higher |
| G107-2 (DK-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G107-1 (DK+) - G107-2 (DK-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTCs B1860, B1861, B1862 and B1863 are not output |
| DTC B1860, B1861, B1862 or B1863 is output |
Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.
DTCs B1860, B1861, B1862 and B1863 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B1860, B1861, B1862 or B1863 is output