Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM
RM3620E _58 Vehicle Interior _076039 PRE-COLLISION _0369995 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Missing Message  


DESCRIPTION

The forward recognition camera is connected to the millimeter wave radar sensor assembly via the CAN communication line. When the signal from the millimeter wave radar sensor assembly is interrupted, the forward recognition camera outputs U023587.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Missing Message Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Local bus (Open or short)

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly
(Front Radar Sensor)
Forward Recognition Camera
(Pre-collision System)
U010487 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ Local bus (Open or short)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern 2 - ○ Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

WIRING DIAGRAM

E384731E07
5.677,0.792 6.292,0.99 0.615,0.198 10 false CANH 5.677,1.448 6.292,1.646 0.615,0.198 10 false CANL 5.427,1.25 6.042,1.448 0.615,0.198 10 false 12 5.458,0.771 6.073,0.969 0.615,0.198 10 false 6 1.229,0.781 1.844,0.979 0.615,0.198 10 false CA1P 1.198,1.438 1.813,1.635 0.615,0.198 10 false CA1N 1.667,1.24 2.281,1.438 0.615,0.198 10 false 6 1.677,0.792 2.292,0.99 0.615,0.198 10 false 5 5.26,1.719 7.156,2.292 1.896,0.573 10 false P8 0.625,1.865 3.125,2.375 2.5,0.51 10 false Millimeter Wave Radar Sensor Assembly 0.615,1.708 2.51,2.281 1.896,0.573 10 false B9 5.26,1.875 7.042,2.229 1.781,0.354 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

If the millimeter wave radar sensor assembly has been replaced with a new one, be sure to perform Front Beam Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before troubleshooting, perform CAN bus diagnostics and check that there are no malfunctions in ECUs connected to the CAN communication system.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Pattern DTC Output Part Name
(Display on GTS / Output DTC)
Millimeter Wave Radar Sensor Assembly
(Front Radar Sensor)
Forward Recognition Camera
(Pre-Collision System)
Pattern 1 U010487 U023587
Pattern 2 - U023587

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)

B

6.CHECK FORWARD RECOGNITION CAMERA
2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the P8 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-6 (CANH) - P8-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
P8-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-12 (CANL) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-6 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
P8-12 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FORWARD RECOGNITION CAMERA

NG

4.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)
3.CHECK FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
OK:

DTC U023587 is not output.



Result:
Proceed to
OK
NG



OK

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

4.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)
a.

Reconnect the P8 forward recognition camera connector.


b.

Disconnect the B9 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-5 (CA1P) - B9-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B9-5 (CA1P) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-6 (CA1N) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-5 (CA1P) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B9-6 (CA1N) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

5.CHECK FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
OK:

DTC U023587 is not output.



Result:
Proceed to
OK
NG



OK

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

6.CHECK FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
OK:

DTC U023587 is not output.



Result:
Proceed to
OK
NG



OK

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY