Home › Drivetrain › CLUTCH › CLUTCH STROKE SENSOR (for LHD)
RM3620E _52 Drivetrain _076045 CLUTCH _0370085 CLUTCH STROKE SENSOR(for LHD) A

CLUTCH  CLUTCH STROKE SENSOR(for LHD)  INSTALLATION  


PROCEDURE

Hide 89280 1.INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

Do not drop the clutch pedal stroke sensor.

·

If the clutch pedal stroke sensor has been dropped, replace the clutch pedal stroke sensor with a new one.



a.

When installing a new clutch pedal stroke sensor:

NOTICE:

Do not break the clutch pedal stroke sensor lever set pin before installing the clutch pedal stroke sensor with the 2 nuts.


i.
C403625C01
0.5,0.833 0.667,0.833 0.667,0.833 0.833,0.917 true 0.667,1.333 0.833,1.333 0.833,1.333 0.833,1 true 2.5,0.833 3,0.833 true 0.25,0.75 0.5,0.917 0.25,0.167 10 true *a 0.438,1.25 0.667,1.417 0.229,0.167 10 true *b 3.073,0.75 3.385,0.948 0.313,0.198 10 false *c
*a Clutch Pedal Stroke Sensor Lever
*b Clutch Pedal Groove
*c Clutch Pedal Stroke Sensor Lever Set Pin


Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 6 ft.*lbf)

NOTICE:
·

Engage the sensor lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the sensor.

·

Check that the tip of the sensor lever is protruding from the clutch pedal groove.




ii.

Firmly depress the clutch pedal to break the clutch pedal stroke sensor lever set pin.


iii.

Remove the broken lever set pin.



b.

When reusing the clutch pedal stroke sensor:

i.
C403626C01
0.833,0.75 0.833,0.417 0.833,0.417 0.583,0.417 true 0.667,1.25 0.833,1.25 0.833,1.25 0.833,0.875 true 0.333,0.333 0.583,0.5 0.25,0.167 10 true *a 0.417,1.167 0.667,1.333 0.25,0.167 10 true *b
*a Clutch Pedal Stroke Sensor Lever
*b Clutch Pedal Groove


Install the clutch pedal stroke sensor to the clutch pedal support assembly and tighten the 2 nuts.

NOTICE:
·

Engage the clutch pedal stroke sensor lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the clutch pedal stroke sensor.

·

Check that the tip of the clutch pedal stroke sensor lever is protruding from the clutch pedal groove.





Hide 2.CONNECT WIRE HARNESS CONNECTOR

C403623

a.

Connect the wire harness connector.


Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.ADJUST CLUTCH PEDAL STROKE SENSOR

NOTICE:

When the clutch pedal stroke sensor is being reused, perform the following procedure to adjust it.


a.

Connect the cable to the negative battery terminal.


b.

Connect the GTS to the DLC3 with the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Clutch Stroke Sensor Voltage.

Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607

f.
C403627

Read the stroke sensor value in the Data List, and turn the clutch pedal stroke sensor slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the clutch pedal depressed):

0.96 to 1.04 V



g.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the clutch pedal after turning the power switch on (IG).



h.

Turn the GTS off and turn the power switch off.


i.

Disconnect the GTS from the DLC3.


j.

Disconnect the cable to the negative battery terminal.


Hide 5.INSTALL KNEE AIRBAG ASSEMBLY (for Driver Side)