Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM3620E _52 Drivetrain _076045 CLUTCH _0370087 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C403603C01
2.75,2.167 2.5,2.167 2.5,2.167 2.26,1.583 true 1.167,2.75 1.802,2.75 false 1.083,4.083 1.083,3.479 true 2.833,2.073 3.292,2.271 0.458,0.198 10 false SST 0.969,2.656 1.281,2.854 0.313,0.198 10 false *1 2.333,3.333 2.646,3.531 0.313,0.198 10 false *a 0.958,4.146 1.417,4.344 0.458,0.198 10 false SST
*1 Clutch Disc Assembly
*a Flywheel side


a.

Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

SST
09301-00210  

NOTICE:

Insert the clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C403604C01
1.219,1.292 0.552,1.875 0.552,1.875 1.125,1.302 true 0.365,1.844 0.677,2.042 0.313,0.198 10 false *a 2.302,0.073 3.208,0.25 0.906,0.177 10 true 1 (*b), 4 2.229,1.906 2.385,2.104 0.156,0.198 10 false 2 0.76,0.885 0.917,1.083 0.156,0.198 10 true 3 2.729,0.792 2.885,0.99 0.156,0.198 10 false 5 1.052,1.781 1.208,1.979 0.156,0.198 10 true 6 1.167,0.208 1.323,0.406 0.156,0.198 10 true 7
*a Matchmarks
*b Temporarily install


a.

Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the procedure shown in the illustration, fully tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C403605N01
2.167,3.667 2.583,2.417 2.583,2.417 2.75,2.417 true 2.833,2.333 3.292,2.531 0.458,0.198 10 false SST

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)


If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31482F 4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE

a.
C401547

Install the clamp to a new clutch release cylinder with bearing assembly to bleeder tube.


b.
C401900

Temporarily install the clutch release cylinder with bearing assembly to bleeder tube to the clutch release bleeder sub-assembly.


c.
C401901C01
1.74,1.813 1.896,2.021 1.896,2.021 2.01,2.021 true 2.063,1.906 2.344,2.104 0.281,0.198 10 false *a
*a Paint Mark


Temporarily intall the clamp to the clutch release cylinder with bearing assembly to bleeder tube.

NOTICE:

Make sure that the paint mark of the clutch release cylinder with bearing assembly to bleeder tube is within the location shown in the illustration.



Hide 31400 5.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.

Clean and degrease all installation surfaces for the clutch release cylinder with bearing assembly.


b.

Install a new clutch release cylinder with bearing assembly to the manual transaxle assembly with 2 new bolts as shown in the illustration.

C401902C01
0.823,1.969 0.948,1.969 0.948,1.969 1.052,1.656 true 5.896,1.521 6.521,1.781 6.521,1.781 6.448,1.521 true 3.448,1.104 3.865,0.281 3.865,0.281 4.052,0.281 true 0.604,1.854 0.792,2.042 0.188,0.188 10 true *1 6.542,1.792 6.854,1.948 0.313,0.156 10 false *a 4.125,0.177 4.438,0.333 0.313,0.156 10 false *b
*1 Clutch Release Cylinder with Bearing Assembly - -
*a Boot *b Dust Bellows


Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)

NOTICE:
·

The clutch release cylinder with bearing assembly and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure that the clutch release cylinder with bearing assembly fits securely with the manual transaxle assembly during installation. The first bolt should be tightened by hand while holding the clutch release cylinder with bearing assembly.

·

Ensure that none of the clutch spline grease adheres to the clutch release cylinder with bearing assembly.

·

The clutch release cylinder with bearing assembly cannot be disassembled.

·

Make sure that the boot is not flipped back.

·

Do not hold the clutch release cylinder with bearing assembly by the dust bellows. If the dust bellows is displaced, moisture or foreign matter may enter and degrade operational performance.




c.
C401906C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft splines.

Grease:

Toyota genuine clutch spline grease or equivalent



Hide 31407B 6.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C401903C01
2.344,1.177 2.813,1.177 true 0.5,0.656 0.677,0.656 0.677,0.656 1.031,1.042 true 2.875,1.063 3.104,1.281 0.229,0.219 10 true *1 0.271,0.531 0.469,0.74 0.198,0.208 10 true *a
*1 Clutch Release Cylinder with Bearing Assembly to Bleeder Tube
*a Adapter


Connect the clutch release cylinder with bearing assembly to bleeder tube to the adapter.

NOTICE:
·

Confirm that the adapter makes a "click" sound when pushed.

·

Check that the clutch release cylinder with bearing assembly to bleeder tube and adapter are securely connected by pulling on them.

·

When connecting the bleeder tube to the adapter of the clutch release cylinder with bearing assembly, hold the back of the adapter to support it.




b.
C401904

Install the clutch release bleeder sub-assembly to the manual transaxle assembly with the bolt as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
C401546

Tighten the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.
C401905C01
1.49,1.458 1.802,1.615 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the clutch release cylinder with bearing assembly to bleeder tube to the clutch release bleeder sub-assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the clutch release cylinder to flexible hose tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31488F 7.INSTALL BLEEDER TO FLEXIBLE HOSE TUBE

a.

Install the clamp to the bleeder to flexible hose tube.


b.
C401907

Temporarily install the bleeder to flexible hose tube to the clutch release bleeder sub-assembly.


c.

Install the bleeder to flexible hose tube to the manual transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.
C401908C01
1.656,2.385 1.958,2.656 0.302,0.271 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the bleeder to flexible hose tube to the clutch release bleeder sub-assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the bleeder clutch release tube.

·

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)