Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM3620E _56 Audio / Visual / Telematics _076048 NAVIGATION / MULTI INFO DISPLAY _0370120 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E408513E01
1.052,4.792 5.333,4.99 4.281,0.198 10 false Steering Pad Switch Assembly 4.115,3.354 5.885,3.719 1.771,0.365 10 false Spiral Cable Sub-assembly 6.292,3.51 7.021,4.479 0.729,0.969 10 false Radio and Display Receiver Assembly 6.292,3.365 6.75,3.563 0.458,0.198 10 false G3 2.573,2.365 3.344,2.771 0.771,0.406 10 false MODE 1.396,3.781 2.521,4.031 1.125,0.25 10 false TEL 2.167,3.802 2.625,4 0.458,0.198 10 false Voice 0.406,1.26 1.479,1.458 1.073,0.198 10 false Volume- 1.177,1.271 2.25,1.469 1.073,0.198 10 false Volume+ 1.99,1.281 3.063,1.479 1.073,0.198 10 false Seek- 2.604,1.271 3.677,1.469 1.073,0.198 10 false Seek+ 4.813,2.833 5.281,3.042 0.469,0.208 10 false AU2 4.813,1.729 5.281,1.938 0.469,0.208 10 false EAU 4.823,0.615 5.292,0.823 0.469,0.208 10 false AU1 4.385,0.698 4.698,0.896 0.313,0.198 10 false z6 5.344,1.823 5.802,2.021 0.458,0.198 10 false G20 4.417,0.521 4.729,0.719 0.313,0.198 10 false 3 4.385,1.625 4.698,1.823 0.313,0.198 10 false 10 4.406,2.719 4.719,2.917 0.313,0.198 10 false 9 5.354,0.521 5.667,0.719 0.313,0.198 10 false 12 5.396,2.729 5.708,2.927 0.313,0.198 10 false 5 5.406,1.625 5.719,1.823 0.313,0.198 10 false 4 6.104,2.833 6.417,3.031 0.313,0.198 10 false 22 6.104,1.729 6.417,1.927 0.313,0.198 10 false 24 6.104,0.615 6.417,0.813 0.313,0.198 10 false 21 6.333,0.698 6.802,0.906 0.469,0.208 10 false SW1 6.333,1.833 6.802,2.042 0.469,0.208 10 false SWG 6.323,2.917 6.792,3.125 0.469,0.208 10 false SW2 5.344,2.927 5.802,3.125 0.458,0.198 10 false G20 5.333,0.708 5.792,0.906 0.458,0.198 10 false G20 4.396,1.813 4.708,2.01 0.313,0.198 10 false z6 4.406,2.938 4.719,3.135 0.313,0.198 10 false z6

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Gasoline Model: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION

for HV Model: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the G3 radio and display receiver assembly connector.


b.

Disconnect the G20 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-21 (SW1) - G20-12 (AU1) Always Below 1 Ω
G3-22 (SW2) - G20-5 (AU2) Always Below 1 Ω
G3-24 (SWG) - G20-4 (EAU) Always Below 1 Ω
G3-21 (SW1) - Body ground Always 10 kΩ or higher
G3-22 (SW2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR