1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Dual Type)
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any defects are found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | w/ Steering Heater | - | - |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
*b | Color: Light Green |
| *c | Color: Black | - | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
Inspect the SRS airbag circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G21-1 (D+) - z3-2 | Always | Below 1.3 Ω |
| G21-2 (D-) - z3-1 | Always | Below 1.3 Ω |
| G21-3 (D2-) - z4-1 | Always | Below 1.3 Ω |
| G21-4 (D2+) - z4-2 | Always | Below 1.3 Ω |
Inspect the horn circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-7 (HO) - A | Always | 3 Ω or less |
Inspect the steering pad switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-4 (EAU) -z6-10 | Always | 3 Ω or less |
| G20-5 (AU2) - z6-9 | Always | 3 Ω or less |
| G20-9 (IL-2) - z6-6 | Always | 3 Ω or less |
| G20-10 (+DP2) -z6-5 | Always | 3 Ω or less |
| G20-11 (+DP) -z6-4 | Always | 3 Ω or less |
| G20-12 (AU1) -z6-3 | Always | 3 Ω or less |
| G20-14 (IL+2) - z6-1 | Always | 3 Ω or less |
Inspect the cruise control circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-2 (ECC) -z6-12 | Always | 3 Ω or less |
| G20-6 (DIST) -z6-8 | Always | 3 Ω or less |
| G20-13 (CCS) -z6-2 | Always | 3 Ω or less |
| G20-3 (ASL) -z6-11 | Always | 3 Ω or less |
Inspect the transmission control switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-1 (SDN) - z5-4 | Always | 3 Ω or less |
| G20-2 (ECC) - z5-3 | Always | 3 Ω or less |
| G20-8 (SUP) - z5-2 | Always | 3 Ω or less |
Inspect the steering heater circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G41-2 (EHT) - z7-1 | Always | Below 0.08 Ω |
| G41-4 (BHT) - z7-4 | Always | Below 0.08 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
Inspect the SRS airbag circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G21-1 (D+) - z3-2 | Always | Below 1.3 Ω |
| G21-2 (D-) - z3-1 | Always | Below 1.3 Ω |
| G21-3 (D2-) - z4-1 | Always | Below 1.3 Ω |
| G21-4 (D2+) - z4-2 | Always | Below 1.3 Ω |
Inspect the horn circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-7 (HO) - A | Always | 3 Ω or less |
Inspect the steering pad switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-4 (EAU) -z6-10 | Always | 3 Ω or less |
| G20-5 (AU2) - z6-9 | Always | 3 Ω or less |
| G20-9 (IL-2) - z6-6 | Always | 3 Ω or less |
| G20-10 (+DP2) -z6-5 | Always | 3 Ω or less |
| G20-11 (+DP) -z6-4 | Always | 3 Ω or less |
| G20-12 (AU1) -z6-3 | Always | 3 Ω or less |
| G20-14 (IL+2) - z6-1 | Always | 3 Ω or less |
Inspect the cruise control circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-2 (ECC) -z6-12 | Always | 3 Ω or less |
| G20-6 (DIST) -z6-8 | Always | 3 Ω or less |
| G20-13 (CCS) -z6-2 | Always | 3 Ω or less |
| G20-3 (ASL) -z6-11 | Always | 3 Ω or less |
Inspect the transmission control switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-1 (SDN) - z5-4 | Always | 3 Ω or less |
| G20-2 (ECC) - z5-3 | Always | 3 Ω or less |
| G20-8 (SUP) - z5-2 | Always | 3 Ω or less |
Inspect the steering heater circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G41-2 (EHT) - z7-1 | Always | Below 0.08 Ω |
| G41-4 (BHT) - z7-4 | Always | Below 0.08 Ω |
2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Single Type)
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any defects are found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | w/ Steering Heater | - | - |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
Inspect the SRS airbag circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G21-1 (D+) - z14-2 | Always | Below 1.3 Ω |
| G21-2 (D-) - z14-1 | Always | Below 1.3 Ω |
Inspect the horn circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-7 (HO) - A | Always | 3 Ω or less |
Inspect the steering pad switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-4 (EAU) -z6-10 | Always | 3 Ω or less |
| G20-5 (AU2) - z6-9 | Always | 3 Ω or less |
| G20-9 (IL-2) - z6-6 | Always | 3 Ω or less |
| G20-10 (+DP2) -z6-5 | Always | 3 Ω or less |
| G20-11 (+DP) -z6-4 | Always | 3 Ω or less |
| G20-12 (AU1) -z6-3 | Always | 3 Ω or less |
| G20-14 (IL+2) - z6-1 | Always | 3 Ω or less |
Inspect the cruise control circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-2 (ECC) -z6-12 | Always | 3 Ω or less |
| G20-6 (DIST) -z6-8 | Always | 3 Ω or less |
| G20-13 (CCS) -z6-2 | Always | 3 Ω or less |
| G20-3 (ASL) -z6-11 | Always | 3 Ω or less |
Inspect the transmission control switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-1 (SDN) - z5-4 | Always | 3 Ω or less |
| G20-2 (ECC) - z5-3 | Always | 3 Ω or less |
| G20-8 (SUP) - z5-2 | Always | 3 Ω or less |
Inspect the steering heater circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G41-2 (EHT) - z7-1 | Always | Below 0.08 Ω |
| G41-4 (BHT) - z7-4 | Always | Below 0.08 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
Inspect the SRS airbag circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G21-1 (D+) - z14-2 | Always | Below 1.3 Ω |
| G21-2 (D-) - z14-1 | Always | Below 1.3 Ω |
Inspect the horn circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-7 (HO) - A | Always | 3 Ω or less |
Inspect the steering pad switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-4 (EAU) -z6-10 | Always | 3 Ω or less |
| G20-5 (AU2) - z6-9 | Always | 3 Ω or less |
| G20-9 (IL-2) - z6-6 | Always | 3 Ω or less |
| G20-10 (+DP2) -z6-5 | Always | 3 Ω or less |
| G20-11 (+DP) -z6-4 | Always | 3 Ω or less |
| G20-12 (AU1) -z6-3 | Always | 3 Ω or less |
| G20-14 (IL+2) - z6-1 | Always | 3 Ω or less |
Inspect the cruise control circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-2 (ECC) -z6-12 | Always | 3 Ω or less |
| G20-6 (DIST) -z6-8 | Always | 3 Ω or less |
| G20-13 (CCS) -z6-2 | Always | 3 Ω or less |
| G20-3 (ASL) -z6-11 | Always | 3 Ω or less |
Inspect the transmission control switch circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G20-1 (SDN) - z5-4 | Always | 3 Ω or less |
| G20-2 (ECC) - z5-3 | Always | 3 Ω or less |
| G20-8 (SUP) - z5-2 | Always | 3 Ω or less |
Inspect the steering heater circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
If the result is not as specified, replace the spiral cable sub-assembly. |
||
| G41-2 (EHT) - z7-1 | Always | Below 0.08 Ω |
| G41-4 (BHT) - z7-4 | Always | Below 0.08 Ω |