Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

WIRING DIAGRAM

E402681E01
0.385,3.26 2.052,3.635 1.667,0.375 10 false No. 1 Stereo Jack Adapter Assembly 5.844,3.26 6.802,3.688 0.958,0.427 10 false Radio Receiver Assembly 0.385,3.063 0.865,3.25 0.479,0.188 10 false G16 5.833,3.063 6.792,3.49 0.958,0.427 10 false G67 5.885,0.76 6.208,0.938 0.323,0.177 10 false ALI 5.885,1.198 6.208,1.375 0.323,0.177 10 false ARI 5.896,1.646 6.365,1.823 0.469,0.177 10 false ASGN 1,2.115 1.469,2.292 0.469,0.177 10 false AGND 5.885,2.531 6.292,2.75 0.406,0.219 10 false AUXI 3.521,2.031 4,2.219 0.479,0.188 10 false * 3.135,3.406 4.115,3.583 0.979,0.177 10 false *: Shielded 1.052,0.76 1.646,0.948 0.594,0.188 10 false VAL+ 1.042,1.208 1.635,1.396 0.594,0.188 10 false VAR+ 1.156,1.635 1.75,1.823 0.594,0.188 10 false VA- 5.885,2.125 6.479,2.313 0.594,0.188 10 false AGND 1.01,2.531 1.604,2.719 0.594,0.188 10 false ADPG 5.552,0.656 5.792,0.865 0.24,0.208 10 false 28 5.552,1.094 5.802,1.313 0.25,0.219 10 false 26 5.552,1.531 5.833,1.75 0.281,0.219 10 false 27 5.552,1.979 5.833,2.198 0.281,0.219 10 false 11 5.573,2.417 5.823,2.635 0.25,0.219 10 false 25 1.563,0.656 2.156,0.844 0.594,0.188 10 false 3 1.563,1.104 2.156,1.292 0.594,0.188 10 false 2 1.563,2.021 2.156,2.208 0.594,0.188 10 false 6 1.573,1.542 2.167,1.729 0.594,0.188 10 false 4 1.563,2.438 2.156,2.625 0.594,0.188 10 false 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G67 radio receiver assembly connector.


b.

Disconnect the G16 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-3 (VAL+) - G67-28 (ALI) Always Below 1 Ω
G16-2 (VAR+) - G67-26 (ARI) Always Below 1 Ω
G16-4 (VA-) - G67-27 (ASGN) Always Below 1 Ω
G16-6 (AGND) - G67-11 (AGND) Always Below 1 Ω
G16-5 (ADPG) - G67-25 (AUXI) Always Below 1 Ω
G16-3 (VAL+) - Body ground Always 10 kΩ or higher
G16-2 (VAR+) - Body ground Always 10 kΩ or higher
G16-4 (VA-) - Body ground Always 10 kΩ or higher
G16-6 (AGND) - Body ground Always 10 kΩ or higher
G16-5 (ADPG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR