Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

E402685E01
1.844,0.688 3.396,1.052 1.552,0.365 10 false from Battery*2 3.688,0.844 4.167,1.083 0.479,0.24 10 false RADIO 3.625,1.938 4.583,2.219 0.958,0.281 10 false ECU-ACC 1.656,1.75 3.167,2 1.51,0.25 10 false from ACC Relay*2 5.396,3.281 7.083,3.688 1.688,0.406 10 false Radio Receiver Assembly 5.396,3.094 5.719,3.292 0.323,0.198 10 false G66 5.677,0.708 6.156,0.948 0.479,0.24 10 false +B1 5.677,2.458 6.156,2.698 0.479,0.24 10 false GND1 5.688,1.74 6.167,1.979 0.479,0.24 10 false ACC1 5.427,0.594 5.563,0.802 0.135,0.208 10 false 4 5.417,1.625 5.552,1.833 0.135,0.208 10 false 3 5.438,2.333 5.573,2.542 0.135,0.208 10 false 7 0.688,0.281 2.885,0.552 2.198,0.271 10 false from Engine Stop and Start ECU*1 0.677,1.375 2.844,1.604 2.167,0.229 10 false from Engine Stop and Start ECU*1 0.125,2.667 2.292,2.896 2.167,0.229 10 false *1: w/ Stop and Start System 0.135,3.042 2.302,3.271 2.167,0.229 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure (w/o Stop and Start System).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY POWER SOURCE)
a.
E259248C49
1.51,0.396 1.896,0.594 0.385,0.198 2.615,1.406 2.396,1.406 2.396,1.406 2.135,1.104 true 1.24,1.698 1.417,1.698 1.417,1.698 1.573,1.385 true 2.302,0.708 2.146,0.708 2.146,0.708 1.927,1 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.573,0.417 1.917,0.625 0.344,0.208 10 false G66 2.75,1.333 3.302,1.552 0.552,0.219 10 false +B1 0.792,1.604 1.229,1.802 0.438,0.198 10 false GND1 2.396,0.646 2.948,0.865 0.552,0.219 10 false ACC1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G66-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

G66-4 (+B1) - Body ground Ignition switch off 11 to 14 V*1
10.5 to 16 V*2
G66-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V*1
10.5 to 16 V*2
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR