Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for Gasoline Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0370335 CRUISE CONTROL SYSTEM(for Gasoline Model) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for Gasoline Model)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the cruise control power supply switch signal and each operation switch signal to the ECM.

·

The ECM performs cruise control according to the signal from the steering pad switch assembly.


WIRING DIAGRAM

C408688E01
4.021,2.333 5.792,2.677 1.771,0.344 10 false Spiral Cable Sub-assembly 0.875,2.365 2.792,2.698 1.917,0.333 10 false Steering Pad Switch Assembly (Cruise Control Switch) 3.083,1.167 3.698,1.365 0.615,0.198 10 false MAIN 2.198,1.177 2.813,1.375 0.615,0.198 10 false CANCEL 1.333,1.156 1.948,1.354 0.615,0.198 10 false +RES 0.469,1.156 1.083,1.354 0.615,0.198 10 false -SET 3.844,1.729 4.156,1.927 0.313,0.198 10 false z6 3.833,0.521 4.146,0.719 0.313,0.198 10 false z6 3.875,0.313 4.031,0.51 0.156,0.198 10 false 2 3.844,1.521 4.073,1.719 0.229,0.198 10 false 12 4.635,0.427 5.094,0.625 0.458,0.198 10 false CCS 4.604,1.625 5.063,1.823 0.458,0.198 10 false ECC 5.406,0.542 5.865,0.74 0.458,0.198 10 false G20 5.406,1.74 5.865,1.938 0.458,0.198 10 false G20 5.458,0.281 5.719,0.49 0.26,0.208 10 false 13 5.49,1.5 5.646,1.698 0.156,0.198 10 false 2 6.333,0.542 6.792,0.74 0.458,0.198 10 false CCS 6.031,0.656 6.375,0.865 0.344,0.208 10 false 27 6.51,3.094 6.969,3.292 0.458,0.198 10 false A24 6.479,3.281 6.854,3.531 0.375,0.25 10 false ECM 3.344,0.427 3.802,0.625 0.458,0.198 10 false CCS 3.344,1.635 3.802,1.833 0.458,0.198 10 false ECC 6.042,1.865 6.385,2.073 0.344,0.208 10 false 28 6.323,1.75 6.781,1.948 0.458,0.198 10 false ECCS 6.052,2.646 6.396,2.854 0.344,0.208 10 false 10 6.313,2.531 6.771,2.729 0.458,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 374 18,19,20,41
OK:

The Data List items shown in the table change according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G20 spiral cable sub-assembly connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-13 (CCS) - A24-27 (CCS) Always Below 1 Ω
G20-2 (ECC) - A24-28 (ECCS) Always Below 1 Ω
G20-13 (CCS) or A24-27 (CCS) - Body ground Always 10 kΩ or higher
G20-2 (ECC) or A24-28 (ECCS) - Body ground Always 10 kΩ or higher



d.

Connect the A24 ECM connector.


e.

Connect the G20 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-10 (E1) - Body ground Always Below 1 Ω



c.

Connect the A24 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)