Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for HV Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0370336 CRUISE CONTROL SYSTEM(for HV Model) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for HV Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU assembly. When the hybrid vehicle control ECU assembly receives the signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light switch signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the hybrid vehicle control ECU assembly through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU assembly turns the cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the power switch is on (IG) and the cruise control system is operating, the voltage of the STP and ST1- terminals of the hybrid vehicle control ECU assembly are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU assembly



WIRING DIAGRAM

for LHD:
A421646E09
5.344,3.948 6.917,4.323 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.813,3.99 4.885,4.375 2.073,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.354,3.771 5.813,3.969 0.458,0.198 10 false M7 2.823,3.802 3.281,4 0.458,0.198 10 false A42 3.833,3.448 4.292,3.646 0.458,0.198 10 false STP2 5.667,3.448 6.125,3.646 0.458,0.198 10 false STP1 4.292,3.344 4.604,3.542 0.313,0.198 10 false 6 5.406,3.354 5.719,3.552 0.313,0.198 10 false 25 2.958,2.625 6.938,2.823 3.979,0.198 10 false Stop Light Switch Assembly 2.969,2.458 3.427,2.656 0.458,0.198 10 false A40 5.198,0.896 5.656,1.094 0.458,0.198 10 false A29 5.198,1.677 5.656,1.875 0.458,0.198 10 false A31 5.25,1.469 5.563,1.667 0.313,0.198 10 false 28 5.302,0.677 5.615,0.875 0.313,0.198 10 false 7 5.594,1.583 6.052,1.781 0.458,0.198 10 false ST1- 5.594,0.792 6.052,0.99 0.458,0.198 10 false STP 5.281,2.396 7.042,2.76 1.76,0.365 10 false Hybrid Vehicle Control ECU Assembly 4.094,0.896 4.406,1.094 0.313,0.198 10 false L 4.094,1.698 4.406,1.896 0.313,0.198 10 false L 3.5,1.021 3.813,1.219 0.313,0.198 10 false B 3.5,1.531 3.813,1.729 0.313,0.198 10 false B 3.49,2.031 3.802,2.229 0.313,0.198 10 false GND 4.26,0.792 4.573,0.99 0.313,0.198 10 false 3 4.26,1.583 4.573,1.781 0.313,0.198 10 false 5 3.323,0.917 3.635,1.115 0.313,0.198 10 false 7 3.323,1.417 3.635,1.615 0.313,0.198 10 false 6 3.313,1.917 3.625,2.115 0.313,0.198 10 false 2 2.313,1.177 2.927,1.375 0.615,0.198 10 false STOP 2.042,1.667 4.031,1.865 1.99,0.198 10 false ECU-IG2 NO.3 0.354,1.01 2.646,1.208 2.292,0.198 10 false from J/B-B Fuse 0.052,1.5 3.115,1.698 3.063,0.198 10 false from IG2 NO.2 Relay

for RHD:
A421646E10
5.344,3.927 6.917,4.302 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.813,3.938 4.885,4.323 2.073,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.354,3.75 5.813,3.948 0.458,0.198 10 false M7 2.823,3.75 3.281,3.948 0.458,0.198 10 false A42 3.833,3.448 4.292,3.646 0.458,0.198 10 false STP2 5.667,3.448 6.125,3.646 0.458,0.198 10 false STP1 4.292,3.344 4.604,3.542 0.313,0.198 10 false 6 5.406,3.354 5.719,3.552 0.313,0.198 10 false 25 2.958,2.625 6.938,2.823 3.979,0.198 10 false Stop Light Switch Assembly 2.969,2.458 3.427,2.656 0.458,0.198 10 false A40 5.198,0.896 5.656,1.094 0.458,0.198 10 false A29 5.198,1.677 5.656,1.875 0.458,0.198 10 false G64 5.24,1.469 5.552,1.667 0.313,0.198 10 false 28 5.281,0.677 5.594,0.875 0.313,0.198 10 false 7 5.594,1.583 6.052,1.781 0.458,0.198 10 false ST1- 5.594,0.792 6.052,0.99 0.458,0.198 10 false STP 5.281,2.385 7.052,2.781 1.771,0.396 10 false Hybrid Vehicle Control ECU Assembly 4.094,0.896 4.406,1.094 0.313,0.198 10 false L 4.094,1.698 4.406,1.896 0.313,0.198 10 false L 3.5,1.021 3.813,1.219 0.313,0.198 10 false B 3.5,1.531 3.813,1.729 0.313,0.198 10 false B 3.49,2.031 3.802,2.229 0.313,0.198 10 false GND 4.26,0.792 4.573,0.99 0.313,0.198 10 false 3 4.26,1.583 4.573,1.781 0.313,0.198 10 false 5 3.323,0.917 3.635,1.115 0.313,0.198 10 false 7 3.323,1.417 3.635,1.615 0.313,0.198 10 false 6 3.313,1.917 3.625,2.115 0.313,0.198 10 false 2 2.313,1.177 2.927,1.375 0.615,0.198 10 false STOP 2.042,1.667 4.031,1.865 1.99,0.198 10 false ECU-IG2 NO.3 0.354,1.01 2.646,1.208 2.292,0.198 10 false from J/B-B Fuse 0.052,1.5 3.115,1.698 3.063,0.198 10 false from IG2 NO.2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU assembly refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
A418954C27
1.5,0.25 1.917,0.5 0.417,0.25 1.146,1.833 1.396,1.333 true 1.781,1.844 2.031,1.344 true 2.25,1.208 2.667,0.458 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 10 false A40 0.958,1.854 1.417,2.052 0.458,0.198 10 false GND 1.729,1.854 2.188,2.052 0.458,0.198 10 false B 2.708,0.375 3.167,0.573 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A40 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-7 (B) - Body ground Always 11 to 14 V
A40-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A40-6 (B) - Body ground Power switch off Below 1 V



d.

Connect the A40 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

for LHD:

Disconnect the A29 and A31 hybrid vehicle control ECU assembly connector.


c.

for RHD:

Disconnect the A29 and G64 hybrid vehicle control ECU assembly connector.


d.

Disconnect the A40 stop light switch assembly connector.


e.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


f.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A31-28 (ST1-) - A40-5 (L) Always Below 1 Ω
A29-7 (STP) - A40-3 (L) Always Below 1 Ω
A31-28 (ST1-) or A40-5 (L) - Body ground Always 10 kΩ or higher
A29-7 (STP) or A40-3 (L) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G64-28 (ST1-) - A40-5 (L) Always Below 1 Ω
A29-7 (STP) - A40-3 (L) Always Below 1 Ω
G64-28 (ST1-) or A40-5 (L) - Body ground Always 10 kΩ or higher
A29-7 (STP) or A40-3 (L) - Body ground Always 10 kΩ or higher



h.

Connect the M7 certification ECU (smart key ECU assembly) connector.


i.

Connect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


j.

Connect the A40 stop light switch assembly connector.


k.

for RHD:

Connect the A29 and G64 hybrid vehicle control ECU assembly connector.


l.

for LHD:

Connect the A29 and A31 hybrid vehicle control ECU assembly connector.


m.

Connect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR