Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0370694 VALVE BODY ASSEMBLY A

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission valve body assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Transmission valve body assembly

·

Solenoid (SL1, SL2, SL3, SL4, SL5 and/or SL6) valve


·

Perform reset memory

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)

PROCEDURE

Hide 35410 2.REMOVE TRANSMISSION VALVE BODY ASSEMBLY (w/o Stop And Start System)

a.
C361011

Disengage the clamp to disconnect the transmission revolution sensor (NC) wire connector.


b.
C369211

Remove the 9 bolts and transmission valve body assembly from the automatic transaxle case sub-assembly.


c.
C369212C01
2.708,1.688 2.948,1.885 0.24,0.198 10 true *1 2.635,1.99 2.854,2.167 0.219,0.177 10 true *1 2.031,0.302 2.24,0.49 0.208,0.188 10 true *1 1.198,1.938 1.406,2.135 0.208,0.198 10 true *2 1.135,1.615 1.344,1.813 0.208,0.198 10 true *3
*1 Transaxle Case Gasket
*2 No. 1 Front Oil Pump Cover Gasket
*3 No. 2 Front Oil Pump Cover Gasket


Remove the 2 transaxle case gaskets from the automatic transaxle case sub-assembly.


d.

Remove the transaxle case gasket from the counter drive gear sub-assembly.


e.

Remove the No. 1 front oil pump cover gasket from the front oil pump assembly.


f.

Remove the No. 2 front oil pump cover gasket from the front oil pump assembly.


Hide 35410 3.REMOVE TRANSMISSION VALVE BODY ASSEMBLY (w/ Stop And Start System)

a.
C361011

Disengage the clamp to disconnect the transmission revolution sensor (NC) wire connector.


b.
C385861

Remove the 9 bolts and transmission valve body assembly from the automatic transaxle case sub-assembly.


c.
C389756C01
1.76,0.24 1.958,0.427 0.198,0.188 10 true *1 1,1.979 1.198,2.167 0.198,0.188 10 true *2 0.875,1.531 1.063,1.708 0.188,0.177 10 true *3 2.458,1.615 2.656,1.802 0.198,0.188 10 true *1 2.396,1.917 2.594,2.104 0.198,0.188 10 true *1 0.969,1.063 1.167,1.26 0.198,0.198 10 true *1
*1 Transaxle Case Gasket
*2 No. 1 Front Oil Pump Cover Gasket
*3 No. 2 Front Oil Pump Cover Gasket


Remove the 2 transaxle case gaskets from the automatic transaxle case sub-assembly.


d.

Remove the transaxle case gasket from the counter drive gear sub-assembly.


e.

Remove the transaxle case gasket from the front oil pump assembly.


f.

Remove the No. 1 front oil pump cover gasket from the front oil pump assembly.


g.

Remove the No. 2 front oil pump cover gasket from the front oil pump assembly.