Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370842 AIR CONDITIONING SYSTEM(for HV Model) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  Cooling is Poor  


DESCRIPTION

If the cooling air is poor (cooling air is discharged), the following causes are possible.

Malfunction Status Factor
·

Cooling is poor.

·

Takes time to cool down.


·

ECO drive mode function (air flow volume is restricted due to ECO drive mode being selected)

·

Compressor with motor assembly malfunction

·

Excessive refrigerant

·

Lack of refrigerant gas

·

Dirty cooler condenser

·

Cooling fan system malfunction

·

Air mix damper and link operation (jamming)

·

Automatic light control sensor

·

Warm air flow



WIRING DIAGRAM

E366622E13
0.229,1.021 1.802,1.396 1.573,0.375 10 false Air Conditioning Amplifier Assembly 1.844,3.865 3.208,4.021 1.365,0.156 10 false H1 1.854,4.021 4.073,4.219 2.219,0.198 10 false Automatic Light Control Sensor 4.646,3.969 6.01,4.125 1.365,0.156 10 false G44 4.646,4.125 6.833,4.552 2.188,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.021,4.479 3.24,4.677 2.219,0.198 10 false : CAN Communication Line 4.594,1.646 5.052,1.823 0.458,0.177 10 false 23 4.885,1.646 5.344,1.823 0.458,0.177 10 false CLTB 4.594,2.427 5.052,2.604 0.458,0.177 10 false 24 4.906,2.427 5.365,2.604 0.458,0.177 10 false CLTS 4.615,3.094 5.073,3.271 0.458,0.177 10 false 25 4.906,3.083 5.365,3.26 0.458,0.177 10 false CLTE 3.104,1.646 3.563,1.823 0.458,0.177 10 false CLTB 3.625,1.656 4.083,1.833 0.458,0.177 10 false 1 3.125,2.438 3.583,2.615 0.458,0.177 10 false CLTS 3.615,2.427 4.073,2.604 0.458,0.177 10 false 4 3.615,3.104 4.073,3.281 0.458,0.177 10 false 2 3.125,3.115 3.583,3.292 0.458,0.177 10 false CLTE

PROCEDURE

1.CHECK ECO DRIVE MODE OPERATION
a.

Confirm setup of the ECO drive mode and turn it off if it is on.

HINT:
·

When ECO drive mode is on, the air conditioning amplifier assembly ensures a minimum level of air conditioning control based on certain conditions, thereby contributing to improved fuel efficiency. Accordingly, explain to customers that the air volume will be weaker in these situations.

Control Control Summary
Airflow Control Automatically switches the air inlet port to the internal air circulation mode when the outside air temperature is equal to or higher than a predetermined temperature and reduces the power consumption.
Air Inlet Control Sets the blower level in AUTO mode lower than normal, and suppresses the power consumption.

·

If integration control and panel assembly (ECO switch) is malfunctioning, perform diagnosis on the ECO switch circuit.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>ECO Switch Circuit




Result:
Proceed to
NEXT



NEXT

2.CHECK REFRIGERANT PRESSURE
2.CHECK REFRIGERANT PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioner pressure sensor Min.: -0.4566 MPaG (gauge)
Max.: 3.2943 MPaG (gauge)
Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioner pressure sensor system malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 121 51


g.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Measurement Condition:
Item Condition
Vehicle Condition Power switch on (READY)
Doors Fully closed (windows also fully closed)
A/C Switch On
Recirculation/fresh Control Switch Recirculation
Set Temperature MAX COLD
Blower Speed HI
Air Conditioning Air Inlet Temperature 25 to 35°C (77 to 95°F)

Standard Pressure:
Low pressure side:

150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)




h.

Compare the values displayed in the Data List and on the manifold gauge.

OK:

The values displayed in the Data List and on the manifold gauge match.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (SERVO PULSE)

NG

3.PERFORM ACTIVE TEST USING GTS (SERVO PULSE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) pulse Min.: 128
Max.: 383
for LHD:

Operates between 165 to 257 pulses


for RHD:

Operates between 255 to 347 pulses


Air Mix Servo Targ Pulse(P) No. 1 air conditioning radiator damper servo sub-assembly (front passenger side air mix) pulse Min.: 128
Max.: 383
for LHD:

Operates between 255 to 347 pulses


for RHD:

Operates between 165 to 257 pulses


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(P)
50004 121 25
OK:

Damper servo motor is operated.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H1 automatic light control sensor connector.


b.

Disconnect the G44 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 (CLTB) - G44-23 (CLTB) Always Below 1 Ω
H1-2 (CLTE) - G44-25 (CLTE) Always Below 1 Ω
H1-4 (CLTS) - G44-24 (CLTS) Always Below 1 Ω
H1-1 (CLTB) or G44-23 (CLTB) - Other terminals and body ground Always 10 kΩ or higher
H1-2 (CLTE) or G44-25 (CLTE) - Other terminals and body ground Always 10 kΩ or higher
H1-4 (CLTS) or G44-24 (CLTS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Remove the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR