Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Hybrid Vehicle Control" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Hybrid Vehicle Control" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Hybrid Vehicle Control" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Hybrid Vehicle Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Hybrid vehicle control ECU assembly branch wire or connector

·

Power source circuit of hybrid vehicle control ECU assembly

·

Hybrid vehicle control ECU assembly ground circuit

·

Hybrid vehicle control ECU assembly



WIRING DIAGRAM

C405923E02
5.573,0.396 5.885,0.594 0.313,0.198 10 false A31 5.563,0.844 5.875,1.042 0.313,0.198 10 false A31 5.563,2.948 5.875,3.146 0.313,0.198 10 false A30 5.573,3.385 5.885,3.583 0.313,0.198 10 false A29 5.573,3.854 5.885,4.052 0.313,0.198 10 false A29 5.563,4.302 5.875,4.5 0.313,0.198 10 false A30 5.146,0.406 5.458,0.604 0.313,0.198 10 false G64 5.146,0.833 5.458,1.031 0.313,0.198 10 false G64 5.563,4.74 5.875,4.938 0.313,0.198 10 false A31 5.563,6.208 5.875,6.406 0.313,0.198 10 false A31 5.583,5.313 5.896,5.51 0.313,0.198 10 false A31 5.552,5.771 5.865,5.969 0.313,0.198 10 false A31 5.573,6.656 5.885,6.854 0.313,0.198 10 false A30 5.948,0.385 6.469,0.615 0.521,0.229 10 false CA1H 5.958,0.833 6.479,1.063 0.521,0.229 10 false CA1L 5.938,3.865 6.458,4.094 0.521,0.229 10 false MREL 5.938,3.396 6.458,3.625 0.521,0.229 10 false +B1 5.938,2.948 6.458,3.177 0.521,0.229 10 false +B2 5.927,4.271 6.448,4.5 0.521,0.229 10 false BATT 5.948,4.708 6.469,4.938 0.521,0.229 10 false IG2 5.958,6.219 6.479,6.448 0.521,0.229 10 false E12 5.969,5.354 6.49,5.583 0.521,0.229 10 false E01 5.958,5.781 6.479,6.01 0.521,0.229 10 false E02 5.99,6.604 6.51,6.833 0.521,0.229 10 false E1 5.552,0.188 5.865,0.385 0.313,0.198 10 false 21*2 5.594,0.635 5.906,0.833 0.313,0.198 10 false 8*2 5.594,2.75 5.906,2.948 0.313,0.198 10 false 1*2 5.625,3.188 5.938,3.385 0.313,0.198 10 false 11 5.656,3.646 5.969,3.844 0.313,0.198 10 false 5 5.531,4.094 5.844,4.292 0.313,0.198 10 false 27*2 5.531,4.531 5.875,4.729 0.344,0.198 10 false 35*2 5.552,5.99 5.865,6.188 0.313,0.198 10 false 34*2 5.552,5.125 5.865,5.323 0.313,0.198 10 false 12*2 5.531,5.542 5.844,5.74 0.313,0.198 10 false 11*2 5.583,6.458 5.896,6.656 0.313,0.198 10 false 3*2 5.135,0.188 5.448,0.385 0.313,0.198 10 false 21*1 5.167,0.625 5.479,0.823 0.313,0.198 10 false 8*1 5.125,7.167 6.833,7.604 1.708,0.438 10 false Hybrid Vehicle Control ECU Assembly 3.49,3.229 4.49,3.458 1,0.229 10 false IGCT NO.2 3.458,4.135 4.458,4.375 1,0.24 10 false ECU-B NO.2 3.427,4.573 4.427,4.813 1,0.24 10 false ECU IG2 NO.1 1.302,4.708 2.729,4.927 1.427,0.219 10 false from IG2 NO. 1 Relay 1.573,3.354 3,3.573 1.427,0.219 10 false from IGCT Relay 1.719,3.833 3.146,4.052 1.427,0.219 10 false to IGCT Relay 1.302,4.292 2.729,4.51 1.427,0.219 10 false from Auxiliary Battery 0.229,0.969 0.75,1.198 0.521,0.229 10 false G103 0.229,1.135 2.271,1.438 2.042,0.302 10 false No. 3 CAN Junction Connector 1.75,0.313 2.063,0.51 0.313,0.198 10 false 5 1.719,0.75 2.031,0.948 0.313,0.198 10 false 15 0.365,6.979 1.365,7.219 1,0.24 10 false *1: for RHD 0.365,7.365 1.365,7.604 1,0.24 10 false *2: for LHD 5.135,5.333 5.448,5.531 0.313,0.198 10 false G64 5.135,5.771 5.448,5.969 0.313,0.198 10 false G64 5.135,6.208 5.448,6.406 0.313,0.198 10 false G64 5.135,4.729 5.448,4.927 0.313,0.198 10 false G64 5.146,2.938 5.458,3.135 0.313,0.198 10 false G63 5.135,4.302 5.448,4.5 0.313,0.198 10 false G63 5.135,6.656 5.448,6.854 0.313,0.198 10 false G63 5.167,2.74 5.479,2.938 0.313,0.198 10 false 1*1 5.135,4.094 5.448,4.292 0.313,0.198 10 false 27*1 5.104,4.531 5.458,4.698 0.354,0.167 10 false 35*1 5.146,5.125 5.458,5.323 0.313,0.198 10 false 12*1 5.125,5.552 5.438,5.75 0.313,0.198 10 false 11*1 5.146,6 5.458,6.198 0.313,0.198 10 false 34*1 5.156,6.458 5.469,6.656 0.313,0.198 10 false 3*1 0.26,2.615 2.302,2.917 2.042,0.302 10 false No. 4 CAN Junction Connector 5.969,1.823 6.49,2.052 0.521,0.229 10 false CA3P 5.948,2.292 6.469,2.521 0.521,0.229 10 false CA3N 0.25,2.427 0.771,2.656 0.521,0.229 10 false G104 1.74,1.771 2.052,1.969 0.313,0.198 10 false 3 1.74,2.198 2.052,2.396 0.313,0.198 10 false 9 5.135,2.302 5.448,2.5 0.313,0.198 10 false G64 5.135,1.865 5.448,2.063 0.313,0.198 10 false G64 5.573,2.323 5.885,2.521 0.313,0.198 10 false A31 5.573,1.854 5.885,2.052 0.313,0.198 10 false A31 5.156,1.635 5.469,1.833 0.313,0.198 10 false 7*1 5.583,1.635 5.896,1.833 0.313,0.198 10 false 7*2 5.552,2.104 5.865,2.302 0.313,0.198 10 false 20*2 5.146,2.104 5.458,2.302 0.313,0.198 10 false 20*1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HYBRID VEHICLE CONTROL ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the hybrid vehicle control ECU assembly connector.

C405899C04
1,1 1.417,1.25 0.417,0.25 1,1.417 1.417,1.667 0.417,0.25 3.844,1.198 4.417,0.25 4.417,0.25 4.583,0.25 true 4,1.417 4.573,0.469 4.573,0.469 4.74,0.469 true 3.719,1.229 3.354,0.26 3.354,0.26 3.188,0.26 true 3.698,1.385 3.198,0.49 3.198,0.49 3.031,0.49 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.083,1.042 1.396,1.24 0.313,0.198 10 false A31 1.073,1.458 1.385,1.656 0.313,0.198 10 false G64 1.469,1.052 1.781,1.25 0.313,0.198 10 false *A 1.469,1.479 1.781,1.677 0.313,0.198 10 false *B 4.677,0.177 5.25,0.406 0.573,0.229 10 false CA1L 4.813,0.396 5.385,0.625 0.573,0.229 10 false CA1H 2.74,0.177 3.313,0.406 0.573,0.229 10 false CA3P 2.583,0.417 3.156,0.646 0.573,0.229 10 false CA3N
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A31-21 (CA1H) - A31-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A31-7 (CA3P) - A31-20 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for RHD
Tester Connection Condition Specified Condition
G64-21 (CA1H) - G64-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G64-7 (CA3P) - G64-20 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the hybrid vehicle control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

C405900C03
3.354,0.063 3.771,0.313 0.417,0.25 5.25,1.917 5.667,2.167 0.417,0.25 1.25,1.917 1.667,2.167 0.417,0.25 1.25,1.5 1.667,1.75 0.417,0.25 5.25,1.5 5.667,1.75 0.417,0.25 4.271,0.917 4.667,0.333 4.667,0.333 4.833,0.333 true 2.5,0.333 2.667,0.333 2.667,0.333 3.375,0.917 true 0.938,1.969 1.104,1.969 1.104,1.969 0.885,2.719 true 0.51,3.042 0.792,3.635 0.792,3.635 0.958,3.635 true 6.552,2.823 6.438,2.219 6.438,2.219 6.604,2.219 true 6.448,3.115 6.448,3.479 6.448,3.479 6.615,3.479 true 6.406,2.813 6.208,1.958 6.208,1.958 6.375,1.958 true 6.333,3.083 6.333,3.583 6.333,3.583 6.167,3.583 true 0.677,2.177 0.844,2.177 0.844,2.177 0.573,2.719 true 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 1.323,1.958 1.75,2.146 0.427,0.188 10 false G63 5.344,1.958 5.74,2.146 0.396,0.188 10 false G64 0.354,2.094 0.781,2.281 0.427,0.188 10 false +B2 3.438,0.104 3.865,0.292 0.427,0.188 10 false A29 4.896,0.26 5.323,0.448 0.427,0.188 10 false +B1 2.063,0.26 2.583,0.458 0.521,0.198 10 false MREL 1.052,3.573 1.573,3.771 0.521,0.198 10 false BATT 6.688,3.375 7.115,3.563 0.427,0.188 10 false IG2 5.885,3.51 6.313,3.698 0.427,0.188 10 false E12 6.677,2.146 7.104,2.333 0.427,0.188 10 false E01 6.438,1.885 6.865,2.073 0.427,0.188 10 false E02 0.719,1.896 1.146,2.083 0.427,0.188 10 false E1 1.333,1.531 1.76,1.719 0.427,0.188 10 false A30 5.354,1.542 5.781,1.729 0.427,0.188 10 false A31 1.76,1.542 2.188,1.729 0.427,0.188 10 false *A 5.75,1.542 6.177,1.729 0.427,0.188 10 false *A 5.75,1.969 6.177,2.156 0.427,0.188 10 false *B 1.771,1.958 2.198,2.146 0.427,0.188 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A31-12 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A31-11 (E02) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A30-3 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A31-34 (E12) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G64-12 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
G64-11 (E02) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
G63-3 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
G64-34 (E12) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A31-35 (IG2) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
A30-27 (BATT) - Body ground Power switch off 11 to 14 V
A29-11 (+B1) - Body ground Battery voltage applied to terminal A29-5 (MREL) 11 to 14 V
A30-1 (+B2) - Body ground

for RHD
Tester Connection Condition Specified Condition
G64-35 (IG2) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
G63-27 (BATT) - Body ground Power switch off 11 to 14 V
A29-11 (+B1) - Body ground Battery voltage applied to terminal A29-5 (MREL) 11 to 14 V
G63-1 (+B2) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR