Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Power Back Door ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Back Door ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Back Door" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Back Door" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Back Door" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Back Door ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Multiplex network door ECU assembly branch wire or connector

·

Power source circuit of multiplex network door ECU

·

Multiplex network door ECU ground circuit

·

Multiplex network door ECU



WIRING DIAGRAM

C280381E66
5.198,6 6.958,6.281 1.76,0.281 10 false Multiplex Network Door ECU 5.646,5.073 7,5.458 1.354,0.385 10 false GND 5.646,4.25 7,4.635 1.354,0.385 10 false IG 5.646,3.438 7,3.823 1.354,0.385 10 false B 5.646,2.583 7,2.969 1.354,0.385 10 false ECUB 5.646,1.438 7,1.823 1.354,0.385 10 false CANN 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANP 1.677,0.698 3.031,1.083 1.354,0.385 10 false 3 1.667,1.271 3.021,1.656 1.354,0.385 10 false 9 0.365,1.771 1.719,2.156 1.354,0.385 10 false N52 0.365,1.938 2.396,2.208 2.031,0.271 10 false No. 7 CAN Junction Connector 1.583,2.573 3.042,2.917 1.458,0.344 10 false from Auxiliary Battery 1.604,4.208 2.958,4.594 1.354,0.385 10 false from IG1 NO.1 Relay 3.74,4.073 5.094,4.458 1.354,0.385 10 false ECU-IG1 NO.4 4.104,3.24 5.021,3.656 0.917,0.417 10 false PBD 5.156,2.583 6.073,3 0.917,0.417 10 false R18 5.146,3.406 6.063,3.823 0.917,0.417 10 false R19 5.146,4.229 6.063,4.646 0.917,0.417 10 false R18 5.146,5.052 6.063,5.469 0.917,0.417 10 false R19 5.146,1.406 6.063,1.823 0.917,0.417 10 false R18 5.146,0.823 6.063,1.24 0.917,0.417 10 false R18 5.188,1.156 6.542,1.542 1.354,0.385 10 false 40 5.188,0.563 6.542,0.948 1.354,0.385 10 false 39 5.188,2.333 6.542,2.719 1.354,0.385 10 false 20 5.219,3.167 5.656,3.521 0.438,0.354 10 false 1 5.188,3.99 6.542,4.375 1.354,0.385 10 false 18 5.188,4.802 6.542,5.188 1.354,0.385 10 false 10 3.885,2.427 5.24,2.813 1.354,0.385 10 false ECU-B NO.2 1.563,3.396 3.021,3.74 1.458,0.344 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C317101C25
1.49,0.188 1.958,0.448 0.469,0.26 2.604,1.948 2.76,1.948 2.76,1.948 2.906,1.292 true 2.292,1.688 2.448,1.688 2.448,1.688 2.771,1.281 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.594,0.229 2.052,0.427 0.458,0.198 10 false R18 1.854,1.552 2.469,1.75 0.615,0.198 10 false CANP 2.177,1.833 2.792,2.042 0.615,0.208 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-39 (CANP) - R18-40 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the multiplex network door ECU connector.


b.
C325480C49
1.5,0.375 1.958,0.615 0.458,0.24 1.417,2.302 1.917,2.552 0.5,0.25 0.542,2.573 0.698,2.573 0.698,2.573 1,3.094 true 2.958,0.729 2.813,0.729 2.813,0.729 2.646,1.24 true 2.813,3.875 2.667,3.875 2.667,3.875 2.292,3.583 true 2.302,1.927 2.49,1.927 2.49,1.927 2.906,1.302 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.594,0.396 2.052,0.594 0.458,0.198 10 false R18 1.542,2.344 2,2.542 0.458,0.198 10 false R19 1.865,1.854 2.344,2.042 0.479,0.188 10 false ECUB 2.875,3.771 3.271,3.99 0.396,0.219 10 false GND 3.021,0.615 3.302,0.885 0.281,0.271 10 false IG 0.385,2.49 0.667,2.75 0.281,0.26 10 false B
*a Front view of wire harness connector
(to Multiplex Network Door ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R19-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R18-20 (ECUB) - Body ground Power switch off 11 to 14 V
R19-1 (B) - Body ground Power switch off 11 to 14 V
R18-18 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR