Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Spiral cable (Steering Angle Sensor)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Steering sensor branch wire or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

C369090E15
4.292,3.375 4.604,3.573 0.313,0.198 10 false *2 4.281,2.74 4.594,2.938 0.313,0.198 10 false *1 5.375,0.573 5.688,0.771 0.313,0.198 10 false 3 5.385,1.167 5.698,1.365 0.313,0.198 10 false 8 5.396,2.552 5.708,2.75 0.313,0.198 10 false 9 5.385,1.927 5.698,2.125 0.313,0.198 10 false 4 5.385,3.51 5.698,3.708 0.313,0.198 10 false 6 5.594,0.688 6.125,0.906 0.531,0.219 10 false CANH 5.583,1.281 6.115,1.5 0.531,0.219 10 false CANL 5.604,2.677 6.135,2.896 0.531,0.219 10 false IG1 5.573,2.031 6.104,2.25 0.531,0.219 10 false BAT 5.594,3.646 6.125,3.865 0.531,0.219 10 false ESS 5.26,3.948 6.417,4.125 1.156,0.177 10 false G68 5.281,4.104 6.865,4.469 1.583,0.365 10 false Steering Sensor 1.198,3.24 2.99,3.5 1.792,0.26 10 false from IG1 NO.1 Relay 0.469,2.646 2.854,2.865 2.385,0.219 10 false from Engine Stop and Start ECU 0.146,4 3.01,4.229 2.865,0.229 10 false *1: w/ Stop and Start System 0.167,4.344 2.948,4.594 2.781,0.25 10 false *2: w/o Stop and Start System 1.677,2.01 3.24,2.271 1.563,0.26 10 false from Battery 3.073,1.896 4.302,2.167 1.229,0.271 10 false ECU-DCC NO.1 3.073,3.146 4.063,3.375 0.99,0.229 10 false ECU-IG1 NO.2 1.635,0.604 1.948,0.802 0.313,0.198 10 false 11 1.646,1.177 1.958,1.375 0.313,0.198 10 false 22 0.146,1.646 2.271,1.927 2.125,0.281 10 false No. 1 CAN Junction Connector 0.146,1.479 0.729,1.708 0.583,0.229 10 false G96

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING SENSOR BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369124C59
0.552,1.615 1.073,1.865 0.521,0.25 1,0.75 1.25,0.75 1.25,0.75 1.667,1.75 true 1.083,2.667 1.333,2.667 1.333,2.667 1.667,2 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.677,1.667 1.104,1.875 0.427,0.208 10 false G68 0.604,0.688 1.063,0.885 0.458,0.198 10 false CANH 0.708,2.594 1.167,2.792 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-3 (CANH) - G68-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369124C60
0.552,1.615 1.073,1.865 0.521,0.25 2.302,0.771 2.052,0.771 2.052,0.771 1.885,1.688 true 0.667,2.25 0.917,2.25 0.917,2.25 1.333,2 true 1.167,2.708 1.417,2.708 1.417,2.708 1.875,2.01 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.677,1.667 1.104,1.875 0.427,0.208 10 false G68 2.375,0.688 2.833,0.885 0.458,0.198 10 false BAT 0.344,2.177 0.802,2.375 0.458,0.198 10 false ESS 0.813,2.656 1.271,2.854 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-6 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G68-4 (BAT) - Body ground Always 11 to 14 V
G68-9 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IG1 terminal) B
NG (Other terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369124C60
0.552,1.615 1.073,1.865 0.521,0.25 2.302,0.771 2.052,0.771 2.052,0.771 1.885,1.688 true 0.667,2.25 0.917,2.25 0.917,2.25 1.333,2 true 1.167,2.708 1.417,2.708 1.417,2.708 1.875,2.01 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.677,1.667 1.104,1.875 0.427,0.208 10 false G68 2.375,0.688 2.833,0.885 0.458,0.198 10 false BAT 0.344,2.177 0.802,2.375 0.458,0.198 10 false ESS 0.813,2.656 1.271,2.854 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-6 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G68-4 (BAT) - Body ground Always 11 to 14 V
G68-9 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR