Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Airbag" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Airbag" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Airbag sensor assembly main wire or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C410332E01
5.625,3.365 5.938,3.563 0.313,0.198 10 false E1 5.615,4.115 5.927,4.313 0.313,0.198 10 false E2 5.604,2.365 5.917,2.563 0.313,0.198 10 false IG2 5.594,0.792 6.042,0.99 0.448,0.198 10 false CANH 5.594,1.604 6.042,1.802 0.448,0.198 10 false CANL 5.344,0.792 5.656,0.99 0.313,0.198 10 false 26 5.333,1.396 5.646,1.594 0.313,0.198 10 false 27 5.354,2.26 5.667,2.458 0.313,0.198 10 false 36 5.365,3.281 5.677,3.479 0.313,0.198 10 false 33 5.375,4 5.688,4.198 0.313,0.198 10 false 32 3.906,2.208 4.729,2.458 0.823,0.25 10 false A/BAG-IG2 5.281,4.896 7.01,5.208 1.729,0.313 10 false Airbag Sensor Assembly 5.302,4.74 5.833,4.969 0.531,0.229 10 false G70 0.156,1.667 0.688,1.896 0.531,0.229 10 false G104 0.156,1.833 2.396,2.156 2.24,0.323 10 false No. 4 CAN Junction Connector 1.656,1.385 1.969,1.583 0.313,0.198 10 false 8 1.688,0.792 2,0.99 0.313,0.198 10 false 2 1.74,2.333 3.51,3.135 1.771,0.802 10 false from IG2 NO.2 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.
B532758C01
1.479,0.135 1.917,0.458 0.438,0.323 2.052,1.344 2.479,0.49 2.479,0.49 2.656,0.49 true 2.156,1.396 2.531,1.813 2.531,1.813 2.708,1.813 true 1.563,0.219 2.021,0.417 0.458,0.198 10 false G70 0.156,0.115 0.615,0.313 0.458,0.198 10 false *a 2.698,0.406 3.156,0.604 0.458,0.198 10 false CANH 2.771,1.729 3.229,1.927 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

w/ Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION

w/o Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-26 (CANH) - G70-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPLACE CAN MAIN WIRE AND CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
B532758C02
1.479,0.135 1.917,0.458 0.438,0.323 1.833,1.583 2.531,0.906 2.531,0.906 2.708,0.906 true 0.719,1.073 0.948,1.073 0.948,1.073 1.75,1.615 true 2.146,1.635 2.635,1.313 2.635,1.313 2.813,1.313 true 1.563,0.219 2.021,0.417 0.458,0.198 10 false G70 0.156,0.115 0.615,0.313 0.458,0.198 10 false *a 2.75,0.833 3.208,1.031 0.458,0.198 10 false E1 0.5,1.01 0.958,1.208 0.458,0.198 10 false E2 2.865,1.24 3.323,1.438 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-32 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G70-33 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G70-36 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS AND CONNECTOR