| Detection Item | Symptom | Trouble Area |
|---|---|---|
| DCM Communication Stop Mode | Any of the following conditions are met:
·
·
|
·
Telephone transceiver assembly branch wire or connector ·
Power source circuit of telephone transceiver assembly ·
Telephone transceiver assembly ground circuit ·
Telephone transceiver assembly |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Disconnect the telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-15 (CANP) - H6-16 (CANN) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Stop and Start System) | A |
| OK (w/o Stop and Start System) | B |
| NG | C |
A
B
C
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-4 (E) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-1 (+B) - Body ground | Always | 10.5 to 16 V |
| H6-8 (ACC) - Body ground | Ignition switch ACC | 10.5 to 16 V |
| Ignition switch off | Below 1 V | |
| H6-7 (IG2) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Ignition switch off | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (+B, ACC or IG2 terminal) | B |
| NG (Other terminal) | C |
A
B
for A25A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>Backup Boost Converter Circuit
for M20A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>Backup Boost Converter Circuit
C
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-4 (E) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-1 (+B) - Body ground | Always | 11 to 14 V |
| H6-8 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| H6-7 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG