Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Panoramic View Monitor" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Panoramic View Monitor" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Panoramic View Monitor" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Parking assist ECU branch wire or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C371289E54
0.135,1.156 0.594,1.354 0.458,0.198 10 false G102 0.135,1.323 2.208,1.698 2.073,0.375 10 false No. 2 CAN Junction Connector 1.542,0.302 2,0.5 0.458,0.198 10 false 5 1.552,0.823 2.01,1.021 0.458,0.198 10 false 15 5.365,0.302 5.823,0.5 0.458,0.198 10 false 11 5.354,0.823 5.813,1.021 0.458,0.198 10 false 12 5.646,0.417 6.104,0.615 0.458,0.198 10 false CANH 5.656,0.927 6.115,1.125 0.458,0.198 10 false CANL 5.438,1.542 5.896,1.74 0.458,0.198 10 false 1 5.635,1.667 6.094,1.865 0.458,0.198 10 false +B 3.969,1.5 5.042,1.729 1.073,0.229 10 false ECU-B NO.2 5.635,2.24 6.094,2.438 0.458,0.198 10 false IG 5.438,2.146 5.896,2.344 0.458,0.198 10 false 3 3.948,2.094 5.083,2.354 1.135,0.26 10 false ECU-IG1 NO.3 2.042,2.844 3.563,3.281 1.521,0.438 10 false from ACC Relay 5.656,2.802 6.115,3 0.458,0.198 10 false ACC 5.438,2.719 5.896,2.917 0.458,0.198 10 false 2 4.042,2.677 4.979,2.875 0.938,0.198 10 false ECU-ACC 5.448,3.365 5.906,3.563 0.458,0.198 10 false 4 5.625,3.51 6.083,3.708 0.458,0.198 10 false GND1 5.333,4.042 5.813,4.333 0.479,0.292 10 false N25 5.344,4.24 7.156,4.667 1.813,0.427 10 false Parking Assist ECU 2.271,1.677 3.24,2.292 0.969,0.615 10 false from Battery 1.771,2.26 3.302,2.667 1.531,0.406 10 false from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369144C53
1.5,0.167 1.917,0.417 0.417,0.25 2.052,2.927 1.885,2.927 1.885,2.927 1.885,2.094 true 2.219,2.76 2.052,2.76 2.052,2.76 2.052,2.094 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false N25 2.125,2.865 2.604,3.073 0.479,0.208 10 false CANH 2.292,2.677 2.771,2.885 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N25-11 (CANH) - N25-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369144C54
1.5,0.167 1.917,0.417 0.417,0.25 2.292,0.969 2.458,0.969 2.458,0.969 2.458,1.719 true 1.156,0.958 0.99,0.958 0.99,0.958 0.99,1.708 true 2.635,0.75 2.802,0.75 2.802,0.75 2.802,1.75 true 0.823,0.729 0.656,0.729 0.656,0.729 0.656,1.729 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false N25 2.073,0.917 2.552,1.125 0.479,0.208 10 false IG 1.229,0.896 1.708,1.104 0.479,0.208 10 false ACC 2.208,0.677 2.688,0.885 0.479,0.208 10 false GND1 0.917,0.667 1.396,0.875 0.479,0.208 10 false +B
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N25-4 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N25-1 (+B) - Body ground Always 11 to 14 V
N25-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
N25-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR