1.SECURE MANUAL TRANSAXLE ASSEMBLY
| *a | Wooden Block |
Place the manual transaxle assembly on wooden blocks.
33101A
2.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33101B
3.REMOVE MANUAL TRANSMISSION DRAIN PLUG
Remove the manual transmission drain plug and gasket from the manual transmission case.
84210
4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
84545
5.REMOVE NEUTRAL POSITION SWITCH
89413B
6.REMOVE TRANSMISSION REVOLUTION SENSOR
31478
7.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP
Remove the release cylinder bleeder plug cap from the release cylinder bleeder plug.
8.REMOVE RELEASE CYLINDER BLEEDER PLUG
Remove the release cylinder bleeder plug from the clutch release bleeder sub-assembly.
31400
9.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31482F
10.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31407B
11.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
33292A
12.REMOVE LOCK BALL PIN
| *1 | Shift and Select Lever Shaft Straight Screw with Head Plug |
| *2 | No. 2 Lock Ball Pin Return Spring |
| *3 | Lock Ball Pin |
Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case.
Using a Magnet Hand, remove the No. 2 lock ball pin return spring and lock ball pin from the manual transmission case.
33292B
13.REMOVE NO. 2 LOCK BALL PIN
| *1 | Shift and Select Lever Shaft Straight Screw with Head Plug |
| *2 | No. 1 Lock Ball Pin Return Spring |
| *3 | No. 2 Lock Ball Pin |
Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the transaxle(MTM) case sub-assembly.
Using a Magnet Hand, remove the No. 1 lock ball pin return spring and No. 2 lock ball pin from the transaxle(MTM) case sub-assembly.
33275C
14.REMOVE SHIFT DETENT BALL
| *1 | Shift Detent Ball Plug |
| *2 | No. 2 Shift Detent Ball Compression Spring |
| *3 | Shift Detent Ball |
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the transaxle(MTM) case sub-assembly.
Using a Magnet Hand, remove the No. 2 shift detent ball compression spring and shift detent ball from the transaxle(MTM) case sub-assembly.
| *1 | Shift Detent Ball Plug |
| *2 | Shift Detent Ball Compression Spring |
| *3 | Shift Detent Ball |
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a Magnet Hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the manual transmission case.
33111
15.REMOVE MANUAL TRANSMISSION CASE
Remove the 18 bolts.
Using a plastic-faced hammer, separate the manual transmission case from the transaxle(MTM) case sub-assembly.
Do not damage the manual transmission case.
| *1 | Outer No. 1 Shift Lever |
| *a | Turn Counterclockwise |
While turning the outer No. 1 shift lever counterclockwise, remove the manual transmission case from the transaxle (MTM) case sub-assembly as shown in the illustration.
| *1 | Inner No. 1 Shift Lever |
| *2 | Inner No. 2 Shift Lever |
| *3 | Outer No. 1 Shift Lever |
| *a | Movement Inside Manual Transaxle Assembly |
As the outer No. 1 shift lever will turn clockwise strongly under its own weight when the manual transmission case is lifted a certain amount and the inner No. 1 shift lever and inner No. 2 shift lever become disengaged, make sure to hold the outer No. 1 shift lever firmly.
33256A
16.REMOVE INNER SELECT LEVER SET BOLT
Using a 6 mm hexagon socket wrench, remove the inner select lever set bolt.
33257
17.REMOVE OUTER SELECT LEVER
Remove the outer select lever from the transaxle(MTM) case sub-assembly.
18.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY
Rotate the shift and select lever shaft assembly counterclockwise to the position shown in the illustration and remove it from the transaxle (MTM) case sub-assembly.
33256
19.REMOVE INNER SELECT LEVER
Remove the inner select lever from the transaxle(MTM) case sub-assembly.
33257C
20.REMOVE OUTER SELECT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the transaxle(MTM) case sub-assembly.
Do not damage the transaxle(MTM) case sub-assembly.
21.REMOVE INPUT SHAFT ASSEMBLY
| *1 | Input Shaft Assembly |
| *2 | Output Shaft Assembly |
| *3 | No. 1 Fork Shaft Assembly |
| *4 | No. 2 Gear Shift Fork Assembly |
| *5 | No. 3 Gear Shift Fork Assembly |
Remove the input shaft assembly together with the output shaft assembly, No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly from the transaxle(MTM) case sub-assembly.
To prevent damage to the front output shaft bearing (inner race), slightly raise the differential case assembly.
Remove the No. 1 fork shaft assembly, No. 2 gear shift fork assembly and No. 3 gear shift fork assembly from the input shaft assembly and output shaft assembly.
33232F
22.REMOVE NO. 1 GEAR SHIFT HEAD
Using a 5 mm pin punch and hammer, remove the shift head set slotted spring pin and No. 1 gear shift head from the No. 1 gear shift fork shaft.
33210
23.REMOVE NO. 1 GEAR SHIFT FORK ASSEMBLY
Using a 5 mm pin punch and hammer, remove the shift fork slotted pin and No. 1 gear shift fork assembly from the No. 1 gear shift fork shaft.
24.REMOVE DIFFERENTIAL CASE ASSEMBLY
| *1 | Differential Case Assembly |
| *2 | No. 2 Output Shaft Assembly |
| *3 | No. 4 Fork Shaft Assembly |
Remove the differential case assembly together with the No. 2 output shaft assembly and No. 4 fork shaft assembly from the transaxle(MTM) case sub-assembly.
Remove the No. 4 fork shaft assembly from the No. 2 output shaft assembly.
33215B
25.REMOVE NO. 4 GEAR SHIFT FORK
Remove the bolt and No. 4 gear shift fork from the No. 4 gear shift fork shaft.
41311E
26.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
| *1 | Front Differential Case Front Tapered Roller Bearing (Outer Race) |
| *2 | Front Differential Oil Baffle |
Using SST, remove the front differential case front tapered roller bearing (outer race) from the transaxle(MTM) case sub-assembly.
Make sure that SST is not hooked on the front differential oil baffle.
Do not damage the transaxle(MTM) case sub-assembly.
| *a | Turn |
| *b | Hold |
Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case sub-assembly.
41311F
27.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
| *1 | Front Differential Case Rear Tapered Roller Bearing (Outer Race) |
| *2 | Front Differential Case Rear Shim |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.
Do not damage the manual transmission case.
| *a | Hold |
| *b | Turn |
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case sub-assembly.
33449B
28.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the transaxle(MTM) case sub-assembly.
33101J
29.REMOVE BREATHER PLUG
Remove the breather plug from the transaxle(MTM) case sub-assembly.
33321N
30.REMOVE FRONT OUTPUT SHAFT BEARING (OUTER RACE)
Using SST, remove the front output shaft bearing (outer race) from the transaxle(MTM) case sub-assembly.
Do not damage the transaxle(MTM) case sub-assembly.
33134B
31.REMOVE OUTPUT SHAFT(MTM) COVER
Remove the output shaft(MTM) cover from the transaxle(MTM) case sub-assembly.
33139G
32.REMOVE REVERSE GEAR SHAFT COVER
Remove the reverse gear shaft cover from the transaxle(MTM) case sub-assembly.
33143C
33.REMOVE FRONT DIFFERENTIAL OIL BAFFLE
Remove the front differential oil baffle from the transaxle(MTM) case sub-assembly.
31105D
34.REMOVE FRONT TRANSAXLE CASE OIL SEAL
Using SST and a hammer, remove the front transaxle case oil seal from the transaxle(MTM) case sub-assembly.
41110G
35.REMOVE DIFFERENTIAL SIDE OIL SEAL
Using SST and a hammer, remove the differentil side oil seal from the transaxle(MTM) case sub-assembly.
31105C
36.REMOVE TRANSAXLE CASE STRAIGHT PIN
Remove the 3 transaxle case straight pins from the transaxle(MTM) case sub-assembly.
33322H
37.REMOVE REAR REVERSE GEAR SHAFT BEARING SHIM
Remove the rear reverse gear shaft bearing shim from the manual transmission case.
33311K
38.REMOVE REAR INPUT SHAFT BEARING SHIM
Remove the rear input shaft bearing shim from the manual transmission case.
33137
39.REMOVE INPUT SHAFT(MTM) COVER
Remove the input shaft(MTM) cover from the manual transmission case.
33124C
40.REMOVE NO. 1 OIL RECEIVER PIPE(MTM)
Disengage the 2 guides and remove the No. 1 oil receiver pipe(MTM) from the manual transmission case.
33253
41.REMOVE OUTER NO. 1 SHIFT LEVER
| *a | Hole |
Using a 5 mm pin punch and hammer, remove the inner shift lever slotted spring pin from the inner No. 1 shift lever.
Perform this step carefully so that the inner shift lever slotted spring pin does not fly out.
When removing the inner shift lever slotted spring pin, align the inner shift lever slotted spring pin with the hole in the neutral position switch.
| *1 | Outer No. 1 Shift Lever |
| *2 | Inner No. 1 Shift Lever |
Remove the outer No. 1 shift lever and inner No. 1 shift lever from the manual transmission case.
33253H
42.REMOVE OUTER SHIFT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the manual transmission case.
Do not damage the manual transmission case.
33321A
43.REMOVE REAR OUTPUT SHAFT BEARING (OUTER RACE)
| *1 | Rear Output Shaft Bearing (Outer Race) |
| *2 | Rear Output Shaft Bearing Shim |
Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.
Do not damage the manual transmission case.
43420H
44.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, remove the front drive shaft oil seal LH from the manual transmission case.