Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › 2018.10–2019.02
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371339 OIL COOLER A

P710 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide G1271C 1.INSTALL NO. 1 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C393925C01
2.5,0.708 2.656,0.906 0.156,0.198 10 false -
V100145

ATF Application Area


Coat the pipe of the motor cooling cooler with a small amount of ATF as shown in the illustration.


b.
C393926C02
1.167,1.198 1.49,0.958 1.49,0.958 1.323,1.198 true 1.76,1.979 1.885,1.979 1.885,1.979 2.135,1.563 false 0.865,0.604 1.073,0.813 0.208,0.208 10 false *a 0.75,1.719 0.99,1.906 0.24,0.188 10 false *b 1.521,0.865 1.75,1.042 0.229,0.177 10 false *c 1.823,1.156 2.063,1.344 0.24,0.188 10 false *d 1.583,1.885 1.885,2.073 0.302,0.188 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 120°
V100145

Claw of Clip Location


Install the No. 1 motor cooling hose to the motor cooling cooler, and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark of the No. 1 motor cooling hose with the paint mark of the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G1272C 2.INSTALL NO. 2 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C393927C01
2.302,1.135 2.458,1.333 0.156,0.198 10 false -
V100145

ATF Application Area


Coat the pipe of the motor cooling cooler with a small amount of ATF as shown in the illustration.


b.
C402373C01
2.042,1.198 1.906,0.927 1.906,0.927 2.219,1.198 true 1.281,1.594 1.5,1.979 1.5,1.979 1.635,1.979 false 2.396,0.583 2.615,0.792 0.219,0.208 10 false *a 2.5,1.708 2.719,1.885 0.219,0.177 10 false *b 1.719,0.813 1.99,1.021 0.271,0.208 10 false *c 1.5,1.146 1.771,1.344 0.271,0.198 10 false *d 1.677,1.875 1.969,2.052 0.292,0.177 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 120°
V100145

Claw of Clip Location


Install the No. 2 motor cooling hose to the motor cooling cooler, and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark of the No. 2 motor cooling hose with the paint mark of the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G1252A 3.INSTALL NO. 2 MOTOR COOLING PIPE

a.
C402374C01
2.073,2.281 2.25,2.5 2.25,2.5 2.146,2.281 false 2.844,4 3.104,4.26 0.26,0.26 10 false *a 2.802,3.25 3.052,3.458 0.25,0.208 10 false *b 2.271,2.49 2.5,2.667 0.229,0.177 10 false *c 1.604,3.594 1.823,3.792 0.219,0.198 10 false *d 1.385,3.458 1.646,3.677 0.26,0.219 10 false *e 1.385,3.75 1.646,3.969 0.26,0.219 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 15°
V100145

Center of Clip Location


Install the No. 2 motor cooling pipe to the No. 2 motor cooling hose, and slide the clip to secure it.

NOTICE:
·

Make sure to align the paint mark of the No. 2 motor cooling pipe with the paint mark of the No. 2 motor cooling hose.

·

Make sure that the center of the clip (between the claws of the clip) is within 15° of the center of the paint mark as shown in the illustration.




Hide G125A 4.INSTALL MOTOR COOLING COOLER

a.
C402375C01
0.531,1.823 0.708,1.823 0.708,1.823 0.813,1.969 true 2.677,2.615 2.958,2.396 true 1.781,2.875 2.208,2.531 true 2.563,2.042 2.75,2.229 0.188,0.188 10 true *b 1.646,2.875 1.865,3.063 0.219,0.188 10 true *c 2.969,2.313 3.188,2.5 0.219,0.188 10 true *d 2.979,2.656 3.188,2.854 0.208,0.198 10 true *e 2.292,2.969 2.521,3.146 0.229,0.177 10 true *a 0.354,1.76 0.531,1.948 0.177,0.188 10 true *f
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Rib
*e Center of Rib
*f 180°
V100145

Claw of Clip Location


Connect the No. 1 motor cooling hose to the transaxle housing tube connector, and slide the clip to secure it.

NOTICE:
·

Make sure to align the paint mark of the No. 1 motor cooling hose with the rib of the hybrid vehicle transaxle assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




b.
C393922N01
1.469,1.958 1.625,2.156 0.156,0.198 10 true 1 0.833,1.281 0.99,1.479 0.156,0.198 10 true 2 2.031,0.115 2.188,0.313 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler to the No. 1 transmission control cable bracket with the 3 bolts.


c.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


d.
C402376C01
2.313,0.531 2.458,0.531 2.458,0.531 2.615,0.802 false 2.198,1.042 2.469,1.042 false 2.146,0.479 2.354,0.698 0.208,0.219 10 false *1 2.021,0.99 2.25,1.208 0.229,0.219 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.


e.
C402377

Install the No. 2 motor cooling pipe to the hose bracket with the bolt and No. 1 oil cooler tube clamp.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


f.
C402378

Tighten the oil cooler union bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide G9229A 5.CONNECT NO. 5 INVERTER COOLING HOSE

Hide G9225K 6.INSTALL NO. 1 INVERTER COOLING HOSE

a.
C402379C01
1.271,3.083 1.406,2.885 1.406,2.885 1.552,2.885 false 2.406,3.458 2.771,3.781 2.771,3.781 2.604,3.469 true 1.979,3.917 2.219,4.104 0.24,0.188 10 false *a 2.823,3.75 3.063,3.969 0.24,0.219 10 false *b 1.51,3.354 1.729,3.573 0.219,0.219 10 false *c 1.604,2.813 1.896,3 0.292,0.188 10 false *d
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark
*c Center of Paint Mark
*d 120°
V100145

Claw of Clip Location


Install the No. 1 inverter cooling hose to the motor cooling cooler, and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark of the No. 1 inverter cooling hose with the paint mark of the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide 9.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 53737D 10.INSTALL FRONT FENDER APRON SEAL LH

Hide 51420 11.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53895B 13.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 14.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH