Home › Drivetrain › EG62F (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL (for RH Side)
RM3620E _52 Drivetrain _076271 EG62F MANUAL TRANSMISSION / TRANSAXLE _0371333 DIFFERENTIAL OIL SEAL(for RH Side) A

EG62F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal RH and differentil side oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 41110G 3.REMOVE DIFFERENTIAL SIDE OIL SEAL

a.
C405629C01
0.708,0.417 1.115,0.417 1.115,0.417 2.24,1.083 true 0.49,0.323 0.719,0.583 0.229,0.26 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the differentil side oil seal from the transaxle(MTM) case sub-assembly.

NOTICE:

Be careful not to damage the transaxle(MTM) case sub-assembly.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C405630N01
0.688,1.583 1.115,1.583 false 0.365,1.5 0.688,1.729 0.323,0.229 10 false SST

Using SST, remove the front drive shaft oil seal RH from the front differential case.

SST
09308-00010  

NOTICE:

Be careful not to damage the front differential case.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C405631C01
2.052,1.615 1.229,0.219 1.229,0.219 2.396,1.438 true 2.188,2.521 2.438,2.76 0.25,0.24 10 false *a 0.906,0.146 1.271,0.365 0.365,0.219 10 false SST
*a Depth


Using SST and a hammer, install the front drive shaft oil seal RH to the front differential case.

SST
09950-60011  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

24.4 to 25.4 mm (0.961 to 1.000 in.)


NOTICE:
·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.

·

Do not remove the grease from the lip of the front drive shaft oil seal RH.




Hide 41110G 6.INSTALL DIFFERENTIAL SIDE OIL SEAL

a.

Coat the lip of a new differentil side oil seal with MP grease.


b.
C405632C01
0.833,1.906 1.052,2.615 1.052,2.615 1.052,1.865 true 2.49,2.74 2.74,2.969 0.25,0.229 10 false *a 0.948,2.646 1.313,2.875 0.365,0.229 10 false SST
*a Depth


Using SST and a hammer, install the differentil side oil seal to the transaxle(MTM) case sub-assembly.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Make sure to install the differentil side oil seal as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the differentil side oil seal.

·

Do not install the differentil side oil seal at an angle.

·

Do not remove the grease from the lip of the differentil side oil seal.




Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 36100 8.INSTALL TRANSFER ASSEMBLY