Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE UNIT
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372438 ENGINE UNIT A

M20A-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the stiffening crankcase assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


c.

Install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12262 2.INSTALL NO. 2 PCV HOSE

a.

Connect the No. 2 PCV hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 25759A 3.INSTALL VACUUM SURGE TANK BRACKET

a.

Install the vacuum surge tank bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17169A 5.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 16032 6.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.

Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16031 7.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 11452 8.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250F 11.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23250F 13.INSTALL PORT FUEL INJECTOR ASSEMBLY

Hide 23291 15.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23807 17.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 82126A 18.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 19.INSTALL SENSOR WIRE

a.

Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 3 clamps.


c.

Connect the 4 connectors.


Hide 16260 20.INSTALL WATER BY-PASS HOSE ASSEMBLY

a.

Install the water by-pass hose assembly and slide the 2 clips to secure them.


b.

Install the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23100X 21.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 22.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 23.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23801P 24.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A426800C01
2.74,2.76 2.844,2.594 false 2.896,2.49 3.208,2.646 0.313,0.156 10 false *a 1.604,2.406 1.917,2.563 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23910A 25.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


c.

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 17177 26.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 16279 29.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.


b.

Install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 31.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 22030 33.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 16278B 34.INSTALL WATER HOSE CLAMP BRACKET

a.

Install the water hose clamp bracket with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16260 35.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.

for CVT:

i.
A433284C01
1.917,3.281 1.708,3.281 1.708,3.281 1.469,2.885 true 1.656,2.167 1.958,2.375 0.302,0.208 10 false *a 0.896,2.792 1.219,2.979 0.323,0.188 10 false *b 1.156,2.594 1.417,2.813 0.26,0.219 10 false *c 1.969,3.188 2.281,3.385 0.313,0.198 10 false *d
*a Top
*b Rear
*c 120° (Claw of Clip Location)
*d Paint Mark


Connect the flow shutting valve (water by-pass hose assembly) to the No. 1 water by-pass pipe sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the No. 1 water by-pass pipe sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




ii.

Install the flow shutting valve (water by-pass hose assembly) to the water hose clamp bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



b.

for Manual Transaxle:

i.
A433286C01
1.594,3.281 1.719,3.281 1.719,3.281 1.979,2.885 true 1.635,2.167 1.948,2.354 0.313,0.188 10 false *a 2.427,2.792 2.708,3 0.281,0.208 10 false *b 2.188,2.573 2.458,2.823 0.271,0.25 10 false *c 1.438,3.198 1.677,3.375 0.24,0.177 10 false *d
*a Top
*b Right
*c 120° (Claw of Clip Location)
*d Paint Mark


Connect the flow shutting valve (water by-pass hose assembly) to the outlet water by-pass sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the outlet water by-pass sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




ii.

Install the flow shutting valve (water by-pass hose assembly) to the water hose clamp bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 16207 36.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass pipe sub-assembly to the water hose clamp bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.
A427767C01
1.417,3.917 1.25,3.917 1.25,3.917 1.042,3.438 true 1.479,3.823 1.792,4.021 0.313,0.198 10 false *a 3,3 3.313,3.198 0.313,0.198 10 false *b 3.021,3.583 3.333,3.781 0.313,0.198 10 false *b
*a Paint Mark
*b 60° (Claw of Clip Location)


Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the No. 2 water by-pass pipe sub-assembly until it contacts the hose stopper of the outlet water by-pass sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




Hide 16572D 37.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16620D 38.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



a.

Install the V-ribbed belt tensioner assembly to the No. 2 timing chain cover assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 88310 39.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

Hide 16361A 41.INSTALL V-RIBBED BELT

Hide 43457 42.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)