INSPECT ILLUMINATED ENTRY SYSTEM OPERATION
Perform this inspection with the customize parameters at the initial settings.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Perform this inspection with the door switch of the map light assembly and No. 1 room light assembly on.
| Control | Condition | Lights that Operate |
|---|---|---|
|
*1: w/ Entry and Start System *2: w/o Entry and Start System *3: w/ Footwell Light *4: w/ Cup Holder Light *5: w/ Tray Light *6: for Manual Transaxle *7: except Manual Transaxle |
||
| Actuation Area-linked*1 | With the ignition switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Door Lock/Unlock-linked | With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Door Open/Close-linked | With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn ON. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| With the ignition switch off and all the doors closed, open the front door and check that the blinking interval for the lights listed on the right slows down. After this, check that the blinking interval for the lights listed on the right quickens when the brake pedal is depressed. | Push start switch illumination | |
| With the ignition switch ON, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off. | ·
Map light assembly ·
No. 1 room light assembly |
|
| Push Start Switch-linked*1 | Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Turn the ignition switch ACC or ON and check that the lights that operate turn on. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
|
| Turn the ignition switch from ACC or ON to off and check that the lights that operate turn off. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
|
| Check that the blinking interval for the lights listed on the right slows down when the ignition switch is turned from ACC or ON to off. | Push start switch illumination | |
| Ignition Switch-linked*2 | Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map light assembly ·
No. 1 room light assembly ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Shift Position-linked*6 | With the ignition switch ACC or ON, move the shift lever from P to any other position and check that the lights that operate dim. While the lights that operate are on, move the shift lever to P and check that the lights that operate return to full brightness. | ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Vehicle Speed-linked*7 | With the ignition switch turned to ACC or ON, release the parking brake, drive the vehicle at least 3 km/h (1.9 mph), and check that the lights dim. While the lights are dim, stop the vehicle, apply the parking brake, and check that the lights return to full brightness. | ·
No. 1 interior illumination light assembly (footwell light)*3 ·
No. 2 interior illumination light assembly (footwell light)*3 ·
No. 3 interior illumination light assembly (center tray light)*5 ·
No. 4 interior illumination light assembly (driver side tray light)*5 ·
No. 5 interior illumination light assembly (front passenger side tray light)*5 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
INSPECT BATTERY SAVING CONTROL OPERATION
The operations and conditions of this control are described below.
| Control | Condition | Lights that Operate |
|---|---|---|
|
*1: w/ Entry and Start System *2: w/ Footwell Light *3: w/ Tray Light *4: w/ Cup Holder Light |
||
| Basic operation | When 20 minutes elapse after the ignition switch is turned from ACC or IG to off and the lights that operate remain on, the lights are turned off.
|
·
Push start switch illumination*1 ·
No. 1 interior illumination light assembly (footwell light)*2 ·
No. 2 interior illumination light assembly (footwell light)*2 ·
No. 3 interior illumination light assembly (center tray light)*3 ·
No. 4 interior illumination light assembly (driver side tray light)*3 ·
No. 5 interior illumination light assembly (front passenger side tray light)*3 ·
No. 6 interior illumination light assembly (cup holder light)*4 |
| Interior light auto cut operation | When 20 minutes elapse after the ignition switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
|
·
Map light assembly ·
No. 1 room light assembly ·
Vanity light assembly |