Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370840 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Parking Support Brake System)  C1AED  Rear Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AED Rear Sensor Communication Malfunction An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the ignition switch is ON.
·

Rear ultrasonic sensor circuit

·

Harness or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

E283768E34
5.604,2.104 6.542,2.292 0.938,0.188 10 false G25*1, H4*2 5.604,2.281 6.802,2.656 1.198,0.375 10 false Clearance Warning ECU Assembly 5.75,1.031 6.365,1.229 0.615,0.198 10 false SOR 5.75,1.302 6.365,1.5 0.615,0.198 10 false BOR 3.969,1.604 4.177,1.813 0.208,0.208 10 false EI 5.479,0.927 5.698,1.115 0.219,0.188 10 false 24 5.469,1.229 5.688,1.417 0.219,0.188 10 false 22 5.469,1.5 5.688,1.688 0.219,0.188 10 false 23 3.042,1.948 3.656,2.146 0.615,0.198 10 false Q12 3.042,2.135 4.917,2.5 1.875,0.365 10 false Rear Corner Ultrasonic Sensor (RL Sensor) 0.698,1.948 1.313,2.146 0.615,0.198 10 false Q11 0.708,2.135 2.594,2.5 1.885,0.365 10 false Rear Center Ultrasonic Sensor (RLC Sensor) 0.719,3.969 1.333,4.167 0.615,0.198 10 false Q10 0.719,4.156 2.594,4.531 1.875,0.375 10 false Rear Center Ultrasonic Sensor (RRC Sensor) 3.021,3.979 3.635,4.177 0.615,0.198 10 false Q9 3.021,4.156 4.927,4.531 1.906,0.375 10 false Rear Corner Ultrasonic Sensor (RR Sensor) 5.75,1.573 6,1.792 0.25,0.219 10 false E1 3.969,1.323 4.177,1.531 0.208,0.208 10 false BI 3.969,1.042 4.177,1.25 0.208,0.208 10 false SI 3.177,1.052 3.479,1.281 0.302,0.229 10 false SO 3.177,1.323 3.448,1.521 0.271,0.198 10 false BO 3.177,1.594 3.458,1.813 0.281,0.219 10 false EO 0.958,1.021 1.25,1.229 0.292,0.208 10 false SO 0.969,1.302 1.229,1.531 0.26,0.229 10 false BO 0.969,1.583 1.271,1.802 0.302,0.219 10 false EO 1.781,1.01 1.99,1.219 0.208,0.208 10 false SI 1.771,1.292 1.979,1.5 0.208,0.208 10 false BI 1.771,1.583 1.979,1.792 0.208,0.208 10 false EI 0.969,3.031 1.177,3.24 0.208,0.208 10 false SI 0.969,3.323 1.177,3.531 0.208,0.208 10 false BI 0.969,3.615 1.177,3.823 0.208,0.208 10 false EI 1.708,3.052 1.979,3.24 0.271,0.188 10 false SO 1.708,3.323 1.969,3.552 0.26,0.229 10 false BO 1.708,3.604 2.01,3.823 0.302,0.219 10 false EO 3.208,3.042 3.417,3.25 0.208,0.208 10 false SI 3.219,3.313 3.427,3.521 0.208,0.208 10 false BI 3.219,3.604 3.427,3.813 0.208,0.208 10 false EI 4.26,0.948 4.479,1.135 0.219,0.188 10 false 3 4.26,1.229 4.479,1.417 0.219,0.188 10 false 1 4.271,1.5 4.49,1.688 0.219,0.188 10 false 5 2.031,0.938 2.25,1.125 0.219,0.188 10 false 3 2.031,1.24 2.25,1.427 0.219,0.188 10 false 1 2.042,1.5 2.26,1.688 0.219,0.188 10 false 5 0.771,2.958 0.99,3.146 0.219,0.188 10 false 3 0.76,3.25 0.979,3.438 0.219,0.188 10 false 1 0.771,3.542 0.99,3.729 0.219,0.188 10 false 5 3,2.969 3.219,3.156 0.219,0.188 10 false 3 3,3.26 3.219,3.448 0.219,0.188 10 false 1 3.01,3.531 3.229,3.719 0.219,0.188 10 false 5 2.958,0.948 3.177,1.135 0.219,0.188 10 false 4 2.958,1.219 3.177,1.406 0.219,0.188 10 false 2 2.958,1.51 3.177,1.698 0.219,0.188 10 false 6 0.781,0.938 1,1.125 0.219,0.188 10 false 4 0.771,1.219 0.99,1.406 0.219,0.188 10 false 2 0.771,1.49 0.99,1.677 0.219,0.188 10 false 6 2.042,2.938 2.26,3.125 0.219,0.188 10 false 4 2.042,3.25 2.26,3.438 0.219,0.188 10 false 2 2.042,3.531 2.26,3.719 0.219,0.188 10 false 6 0.135,5.021 2.635,5.229 2.5,0.208 10 false *1: for LHD and Manual Transaxle 0.135,5.354 2.875,5.552 2.74,0.198 10 false *2: except LHD and Manual Transaxle

PROCEDURE

1.CHECK DTC OUTPUT (C1AED)



Result:
Result Proceed to
DTCs is not output A
DTC C1AED is output B



A

B

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR [RL SENSOR])
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR [RL SENSOR])
a.

Disconnect the G25*1 or H4*2 clearance warning ECU assembly connector.

*1: for LHD and Manual Transaxle

*2: except LHD and Manual Transaxle



b.

Disconnect the Q12 rear corner ultrasonic sensor (RL sensor).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and Manual Transaxle:
Tester Connection Condition Specified Condition
G25-22 (BOR) - Q12-1 (BI) Always Below 1 Ω
G25-24 (SOR) - Q12-3 (SI) Always Below 1 Ω
G25-23 (E1) - Q12-5 (EI) Always Below 1 Ω
G25-22 (BOR) or Q12-1 (BI) - Body ground Always 10 kΩ or higher
G25-24 (SOR) or Q12-3 (SI) - Body ground Always 10 kΩ or higher
G25-23 (E1) or Q12-5 (EI) - Body ground Always 10 kΩ or higher

except LHD and Manual Transaxle:
Tester Connection Condition Specified Condition
H4-22 (BOR) - Q12-1 (BI) Always Below 1 Ω
H4-24 (SOR) - Q12-3 (SI) Always Below 1 Ω
H4-23 (E1) - Q12-5 (EI) Always Below 1 Ω
H4-22 (BOR) or Q12-1 (BI) - Body ground Always 10 kΩ or higher
H4-24 (SOR) or Q12-3 (SI) - Body ground Always 10 kΩ or higher
H4-23 (E1) or Q12-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR [RL SENSOR] - REAR CENTER ULTRASONIC SENSOR [RLC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR [RL SENSOR] - REAR CENTER ULTRASONIC SENSOR [RLC SENSOR])
a.

Disconnect the Q12 rear corner ultrasonic sensor (RL sensor).


b.

Disconnect the Q11 rear center ultrasonic sensor (RLC sensor)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q12-2 (BO) - Q11-1 (BI) Always Below 1 Ω
Q12-4 (SO) - Q11-3 (SI) Always Below 1 Ω
Q12-6 (EO) - Q11-5 (EI) Always Below 1 Ω
Q12-2 (BO) or Q11-1 (BI) - Body ground Always 10 kΩ or higher
Q12-4 (SO) or Q11-3 (SI) - Body ground Always 10 kΩ or higher
Q12-6 (EO) or Q11-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RLC SENSOR] - REAR CENTER ULTRASONIC SENSOR [RRC SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RLC SENSOR] - REAR CENTER ULTRASONIC SENSOR [RRC SENSOR])
a.

Disconnect the Q11 rear center ultrasonic sensor (RLC sensor)


b.

Disconnect the Q10 rear center ultrasonic sensor (RRC sensor).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q11-2 (BO) - Q10-1 (BI) Always Below 1 Ω
Q11-4 (SO) - Q10-3 (SI) Always Below 1 Ω
Q11-6 (EO) - Q10-5 (EI) Always Below 1 Ω
Q11-2 (BO) or Q10-1 (BI) - Body ground Always 10 kΩ or higher
Q11-4 (SO) or Q10-3 (SI) - Body ground Always 10 kΩ or higher
Q11-6 (EO) or Q10-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] - REAR CORNER ULTRASONIC SENSOR [RR SENSOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] - REAR CORNER ULTRASONIC SENSOR [RR SENSOR])
a.

Disconnect the Q10 rear center ultrasonic sensor (RRC sensor).


b.

Disconnect the Q9 rear corner ultrasonic sensor (RR sensor).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q10-2 (BO) - Q9-1 (BI) Always Below 1 Ω
Q10-4 (SO) - Q9-3 (SI) Always Below 1 Ω
Q10-6 (EO) - Q9-5 (EI) Always Below 1 Ω
Q10-2 (BO) or Q9-1 (BI) - Body ground Always 10 kΩ or higher
Q10-4 (SO) or Q9-3 (SI) - Body ground Always 10 kΩ or higher
Q10-6 (EO) or Q9-5 (EI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR CORNER ULTRASONIC SENSOR (RR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR CORNER ULTRASONIC SENSOR (RR SENSOR)
a.

Remove rear corner ultrasonic sensor (RR sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL


b.

Inspect the rear corner ultrasonic sensor (RR sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSPECTION


Result:
Proceed to
OK
NG



OK

7.INSPECT REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)

NG

REPLACE REAR CORNER ULTRASONIC SENSOR (RR SENSOR)

7.INSPECT REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)
a.

Remove the rear center ultrasonic sensor (RRC sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL


b.

Inspect the rear center ultrasonic sensor (RRC sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)

NG

REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)

8.INSPECT REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)
a.

Remove the rear center ultrasonic sensor (RLC sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL


b.

Inspect the rear center ultrasonic sensor (RLC sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT REAR CORNER ULTRASONIC SENSOR (RL SENSOR)

NG

REPLACE REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)

9.INSPECT REAR CORNER ULTRASONIC SENSOR (RL SENSOR)
a.

Remove the rear corner ultrasonic sensor (RL sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL


b.

Inspect the rear corner ultrasonic sensor (RL sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSPECTION


Result:
Proceed to
OK
NG



OK

10.REPLACE REAR CORNER ULTRASONIC SENSOR (RR SENSOR)

NG

REPLACE REAR CORNER ULTRASONIC SENSOR (RL SENSOR)

10.REPLACE REAR CORNER ULTRASONIC SENSOR (RR SENSOR)
a.

Replace the rear corner ultrasonic sensor (RR sensor) with a known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT (C1AED)
11.CHECK DTC OUTPUT (C1AED)


Result:
Result Proceed to
DTC is not output A
DTC C1AED is output B



A

END (REAR CORNER ULTRASONIC SENSOR [RR SENSOR] WAS DEFECTIVE)

B

12.REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)
12.REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR)
a.

Replace the rear center ultrasonic sensor (RRC sensor) with a known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.



Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT (C1AED)
13.CHECK DTC OUTPUT (C1AED)


Result:
Result Proceed to
DTC is not output A
DTC C1AED is output B



A

END (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] WAS DEFECTIVE)

B

14.REPLACE REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)
14.REPLACE REAR CENTER ULTRASONIC SENSOR (RLC SENSOR)
a.

Replace the rear center ultrasonic sensor (RLC sensor) with a known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT (C1AED)
15.CHECK DTC OUTPUT (C1AED)


Result:
Result Proceed to
DTC is not output A
DTC C1AED is output B



A

END (REAR CENTER ULTRASONIC SENSOR [RLC SENSOR] WAS DEFECTIVE)

B

16.REPLACE REAR CORNER ULTRASONIC SENSOR (RL SENSOR)
16.REPLACE REAR CORNER ULTRASONIC SENSOR (RL SENSOR)
a.

Replace the rear corner ultrasonic sensor (RL sensor) with a known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.



Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT (C1AED)
17.CHECK DTC OUTPUT (C1AED)


Result:
Result Proceed to
DTC is not output A
DTC C1AED is output B



A

END (REAR CORNER ULTRASONIC SENSOR [RL SENSOR] WAS DEFECTIVE)

B