Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU (for RHD) › 2018.10–2020.08
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370873 CLEARANCE WARNING ECU(for RHD) A

PARK ASSIST / MONITORING  CLEARANCE WARNING ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clearance warning ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision System
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Clearance warning ECU assembly
·

Ultrasonic sensor detection angle

·

Steering angle neutral point

·

Bumper type registration

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for Gasoline model with parking support brake system)

·

Parking support brake system (for Gasoline model)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Clearance warning ECU assembly
·

Ultrasonic sensor detection angle

·

Steering angle neutral point

·

Bumper type registration

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (for HV model with parking support brake system)

·

Parking support brake system (for HV model)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55308B 7.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 89340A 8.REMOVE CLEARANCE WARNING ECU ASSEMBLY

a.
B525187

Disconnect the 2 connectors.


b.
B525188

Disconnect the connector.


c.
B525189C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver, detach the claw and remove the clearance warning ECU assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.