There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Pre-collision System *2: w/ Blind Spot Monitor System *3: w/ Panoramic View Monitor System *4: w/ TOYOTA Parking Assist-sensor System *5: w/ Grille Shutter System *6: w/ Parking Assist Monitor System |
|
| Resistance between terminals 23 (CA1H) and 8 (CA1L) of central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus wire ·
Short in CAN branch wire ·
Central gateway ECU (network gateway ECU) ·
Forward recognition camera*1 ·
Millimeter wave radar sensor assembly*1 ·
Blind spot monitor sensor LH*2 ·
Parking assist ECU*3 ·
Television camera assembly*3, *6 ·
Clearance warning ECU assembly*4 ·
Swing grille actuator assembly*5 ·
No. 2 CAN junction connector ·
No. 8 CAN junction connector ·
No. 1 CAN junction terminal |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System) |
| *c | to No. 8 CAN Junction Connector | *d | to Swing Grille Actuator Assembly (w/ Grille Shutter System) |
| *e | to Parking Assist ECU (w/ Panoramic View Monitor System) | *f | to Forward Recognition Camera (w/ Pre-collision System) |
| *g | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) | *h | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System *3: w/ Panoramic View Monitor System *4: w/ Grille Shutter System |
|||
| G102-2 (CANH) - G102-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Millimeter wave radar sensor assembly*1 |
| G102-3 (CANH) - G102-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 8 CAN junction connector |
| G102-4 (CANH) - G102-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Swing grille actuator assembly*4 |
| G102-5 (CANH) - G102-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Parking assist ECU*3 |
| G102-6 (CANH) - G102-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Forward recognition camera*1 |
| G102-7 (CANH) - G102-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Clearance warning ECU assembly*2 |
| G102-8 (CANH) - G102-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | B |
| NG (No. 8 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G102 No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-23 (CA1H) - G72-8 (CA1L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the G102 No. 2 CAN junction connector.
Disconnect the No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 8 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) | *d | to Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System) |
| *e | to No. 1 CAN Junction Terminal | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Panoramic View Monitor System *3: w/ Parking Assist Monitor System |
|||
| N53-1 (CANH) - N53-7 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| N53-2 (CANH) - N53-8 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Blind spot monitor sensor LH*1 |
| N53-3 (CANH) - N53-9 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Television camera assembly*2, *3 |
| N53-4 (CANH) - N53-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction terminal |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction terminal CAN main wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the N53 No. 8 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Terminal) |
Disconnect the No. 1 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N54-3 (CANH) - N54-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G72-23 (CA1H) - G72-8 (CA1L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Proceed to |
|---|
| OK |
| NG |
OK
NG