Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2018.10–2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) U

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C405889C01
3.25,0.167 3.667,0.417 0.417,0.25 2.823,0.417 2.99,0.417 2.99,0.417 3.25,1.375 true 2.667,0.583 2.833,0.583 2.833,0.583 3.115,1.375 true 2.5,0.75 2.667,0.75 2.667,0.75 3.01,1.385 true 2.333,0.917 2.5,0.917 2.5,0.917 2.865,1.385 true 2.167,1.083 2.333,1.083 2.333,1.083 2.708,1.406 true 2.833,2.5 3,2.5 3,2.5 3.302,1.708 true 2.667,2.333 2.833,2.333 2.833,2.333 3.135,1.677 true 2.5,2.167 2.667,2.167 2.667,2.167 3,1.667 true 2.333,2 2.5,2 2.5,2 2.833,1.698 true 2.167,1.833 2.333,1.833 2.333,1.833 2.677,1.677 true 4.198,1.385 4.667,1.01 4.667,1.01 4.833,1.01 true 4.208,1.698 4.667,1.917 4.667,1.917 4.833,1.917 true 4.031,1.667 4.5,2.083 4.5,2.083 4.667,2.083 true 3.875,1.698 4.333,2.25 4.333,2.25 4.5,2.25 true 4.063,1.385 4.5,0.833 4.5,0.833 4.667,0.833 true 3.896,1.375 4.333,0.677 4.333,0.677 4.5,0.677 true 3.333,0.208 4.25,0.406 0.917,0.198 10 false G96 0.115,0.115 1.031,0.313 0.917,0.198 10 false *a 1.583,1.031 2.5,1.229 0.917,0.198 10 false CANH*b 1.771,0.844 2.688,1.042 0.917,0.198 10 false CANH*c 1.938,0.667 2.854,0.865 0.917,0.198 10 false CANH*d 2.094,0.49 3.01,0.688 0.917,0.198 10 false CANH*e 2.26,0.323 3.177,0.521 0.917,0.198 10 false CANH*f 1.583,1.75 2.5,1.948 0.917,0.198 10 false CANL*b 1.792,1.927 2.708,2.125 0.917,0.198 10 false CANL*c 1.969,2.094 2.885,2.292 0.917,0.198 10 false CANL*d 2.156,2.271 3.073,2.469 0.917,0.198 10 false CANL*e 2.323,2.448 3.24,2.646 0.917,0.198 10 false CANL*f 4.573,0.583 5.49,0.781 0.917,0.198 10 false CANH*g 4.771,0.771 5.688,0.969 0.917,0.198 10 false CANH*h 4.948,0.958 5.865,1.156 0.917,0.198 10 false CANH*i 4.583,2.198 5.5,2.396 0.917,0.198 10 false CANL*g 4.76,2 5.677,2.198 0.917,0.198 10 false CANL*h 4.948,1.823 5.865,2.021 0.917,0.198 10 false CANL*i
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for No. 7 CAN Junction Connector
*c for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *d for No. 5 CAN Junction Connector
*e for Main Body ECU (Multiplex Network Body ECU) *f for Air Conditioning Amplifier Assembly
*g for No. 4 CAN Junction Connector *h for No. 6 CAN Junction Connector
*i for Steering Sensor - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. Wiring Color Connected to

*: w/ Entry and Start System

G96-1 (CANH) P No. 7 CAN junction connector
G96-12 (CANL) W
G96-2 (CANH) G Certification ECU (smart key ECU assembly)*
G96-13 (CANL) W
G96-3 (CANH) W No. 5 CAN junction connector
G96-14 (CANL) L
G96-4 (CANH) BE Main body ECU (multiplex network body ECU)
G96-15 (CANL) V
G96-5 (CANH) SB Air conditioning amplifier assembly
G96-16 (CANL) W
G96-9 (CANH) SB No. 4 CAN junction connector
G96-20 (CANL) W
G96-10 (CANH) R No. 6 CAN junction connector
G96-21 (CANL) W
G96-11 (CANH) G Steering sensor
G96-22 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C387411C37
0.313,1.219 0.75,1.5 0.438,0.281 1.417,0.76 1.583,0.76 1.583,0.76 2.229,1.396 true 1.396,2.135 1.563,2.135 1.563,2.135 2.24,1.667 true 1.719,0.583 1.885,0.583 1.885,0.583 2.635,1.427 true 1.521,2.323 1.688,2.323 1.688,2.323 2.615,1.656 true 1.948,0.406 2.115,0.406 2.115,0.406 2.99,1.365 true 1.75,2.5 1.917,2.5 1.917,2.5 2.979,1.625 true 2,0.198 2.167,0.198 2.167,0.198 3.354,1.396 true 2.083,2.667 2.25,2.667 2.25,2.667 3.365,1.625 true 4.604,0.208 4.354,0.208 4.354,0.208 3.75,1.385 true 4.51,2.635 4.26,2.635 4.26,2.635 3.76,1.615 true 4.823,0.396 4.573,0.396 4.573,0.396 4.125,1.417 true 4.792,2.396 4.542,2.396 4.542,2.396 4.146,1.594 true 5.115,0.656 4.865,0.656 4.865,0.656 4.51,1.417 true 5.031,2.094 4.781,2.094 4.781,2.094 4.5,1.604 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,1.281 0.781,1.49 0.406,0.208 10 false G102 0.844,2.052 1.427,2.26 0.583,0.208 10 false CANL*b 0.875,0.698 1.458,0.906 0.583,0.208 10 false CANH*b 1.031,2.26 1.615,2.469 0.583,0.208 10 false CANL*c 1.167,0.521 1.75,0.729 0.583,0.208 10 false CANH*c 1.198,2.427 1.781,2.635 0.583,0.208 10 false CANL*d 1.365,0.323 1.948,0.531 0.583,0.208 10 false CANH*d 1.583,2.604 2.26,2.792 0.677,0.188 10 false CANL*e 1.438,0.104 2.021,0.313 0.583,0.208 10 false CANH*e 4.573,2.583 5.156,2.792 0.583,0.208 10 false CANL*f 4.688,0.135 5.271,0.313 0.583,0.177 10 false CANH*f 4.875,2.344 5.458,2.552 0.583,0.208 10 false CANL*g 4.906,0.344 5.49,0.521 0.583,0.177 10 false CANH*g 5.104,2.042 5.688,2.25 0.583,0.208 10 false CANL*h 5.198,0.583 5.781,0.76 0.583,0.177 10 false CANH*h
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System)
*c for No. 8 CAN Junction Connector *d for Swing Grille Actuator Assembly (w/ Grille Shutter System)
*e for Parking Assist ECU (w/ Panoramic View Monitor System) *f for Forward Recognition Camera (w/ Pre-collision System)
*g for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) *h for Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Pre-collision System

*2: w/ Grille Shutter System

*3: w/ Panoramic View Monitor System

*4: w/ TOYOTA Parking Assist-sensor System

G102-2 (CANH) R Millimeter wave radar sensor assembly*1
G102-12 (CANL) W
G102-3 (CANH) B No. 8 CAN junction connector
G102-13 (CANL) W
G102-4 (CANH) G Swing grille actuator assembly*2
G102-14 (CANL) W
G102-5 (CANH) GR Parking assist ECU*3
G102-15 (CANL) W
G102-6 (CANH) L Forward recognition camera*1
G102-16 (CANL) B
G102-7 (CANH) L Clearance warning ECU assembly*4
G102-17 (CANL) W
G102-8 (CANH) P Central gateway ECU (network gateway ECU)
G102-18 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C387411C39
0.313,1.219 0.75,1.5 0.438,0.281 1.24,0.927 1.406,0.927 1.406,0.927 1.865,1.396 true 1.135,1.979 1.302,1.979 1.302,1.979 1.865,1.604 true 1.719,0.667 1.885,0.667 1.885,0.667 2.604,1.375 true 1.51,2.344 1.677,2.344 1.677,2.344 2.635,1.615 true 4.427,0.354 4.177,0.354 4.177,0.354 3.729,1.375 true 4.396,2.458 4.146,2.458 4.146,2.458 3.75,1.656 true 5.49,0.615 5.24,0.615 5.24,0.615 4.885,1.375 true 5.406,2.146 5.156,2.146 5.156,2.146 4.875,1.656 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.375,1.281 0.781,1.49 0.406,0.208 10 false G103 0.604,1.896 1.188,2.104 0.583,0.208 10 false CANL*b 0.677,0.854 1.26,1.063 0.583,0.208 10 false CANH*b 0.969,2.26 1.552,2.469 0.583,0.208 10 false CANL*c 1.177,0.583 1.76,0.792 0.583,0.208 10 false CANH*c 4.458,2.406 5.042,2.615 0.583,0.208 10 false CANL*d 4.521,0.26 5.104,0.438 0.583,0.177 10 false CANH*d 5.5,2.063 6.083,2.271 0.583,0.208 10 false CANL*e 5.583,0.531 6.167,0.708 0.583,0.177 10 false CANH*e
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for ECM *d for Engine Stop and Start ECU (w/ Stop and Start System)
*e for Transmission Control ECU (for CVT) - -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Stop and Start System

*2: for CVT

G103-1 (CANH) SB Central gateway ECU (network gateway ECU)
G103-11 (CANL) W
G103-3 (CANH) G ECM
G103-13 (CANL) W
G103-6 (CANH) R Engine stop and start ECU*1
G103-16 (CANL) W
G103-9 (CANH) L Transmission control ECU*2
G103-19 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C387413C69
0.365,1.271 0.771,1.5 0.406,0.229 1.833,1.135 2,1.135 2,1.135 2.448,1.333 true 1.865,1.729 2.031,1.729 2.031,1.729 2.417,1.563 true 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 4.469,0.219 4.219,0.219 4.219,0.219 3.344,1.281 true 4.115,2.479 3.865,2.479 3.865,2.479 3.333,1.656 true 4.802,0.583 4.552,0.583 4.552,0.583 3.792,1.271 true 4.792,2.208 4.542,2.208 4.542,2.208 3.823,1.635 true 5.188,0.813 4.938,0.813 4.938,0.813 4.26,1.281 true 5.292,1.958 5.042,1.958 5.042,1.958 4.24,1.635 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.406,1.313 0.844,1.51 0.438,0.198 10 false G104 1.313,1.073 1.865,1.25 0.552,0.177 10 false CANH*b 1.354,1.667 1.906,1.844 0.552,0.177 10 false CANL*b 1.417,0.594 1.969,0.771 0.552,0.177 10 false CANH*c 1.469,1.979 2.021,2.156 0.552,0.177 10 false CANL*c 4.521,0.188 5.073,0.365 0.552,0.177 10 false CANH*d 4.177,2.396 4.729,2.573 0.552,0.177 10 false CANL*d 4.875,0.51 5.427,0.688 0.552,0.177 10 false CANH*e 4.854,2.135 5.406,2.313 0.552,0.177 10 false CANL*e 5.292,0.771 5.844,0.948 0.552,0.177 10 false CANH*f 5.344,1.875 5.896,2.052 0.552,0.177 10 false CANL*f
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b for Brake Actuator Assembly (Skid Control ECU)
*c for Airbag Sensor Assembly *d for 4WD ECU Assembly (for 4WD/AWD)
*e for No. 1 CAN Junction Connector *f for Rack and Pinion Power Steering Gear Assembly



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*: for 4WD/AWD

G104-1 (CANH) Y Brake actuator assembly (skid control ECU)
G104-7 (CANL) W
G104-2 (CANH) R Airbag sensor assembly
G104-8 (CANL) W
G104-3 (CANH) W 4WD ECU assembly*
G104-9 (CANL) R
G104-4 (CANH) SB No. 1 CAN junction connector
G104-10 (CANL) W
G104-5 (CANH) G Rack and pinion power steering gear assembly
G104-11 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C405889C02
3.25,0.167 3.667,0.417 0.417,0.25 2.823,0.417 2.99,0.417 2.99,0.417 3.25,1.375 true 2.667,0.583 2.833,0.583 2.833,0.583 3.115,1.375 true 2.5,0.75 2.667,0.75 2.667,0.75 3.01,1.385 true 2.333,0.917 2.5,0.917 2.5,0.917 2.865,1.385 true 2.833,2.5 3,2.5 3,2.5 3.302,1.708 true 2.667,2.333 2.833,2.333 2.833,2.333 3.135,1.677 true 2.5,2.167 2.667,2.167 2.667,2.167 3,1.667 true 2.333,2 2.5,2 2.5,2 2.833,1.698 true 3.313,0.208 4.229,0.406 0.917,0.198 10 false G105 0.115,0.115 1.031,0.313 0.917,0.198 10 false *a 1.771,0.844 2.688,1.042 0.917,0.198 10 false CANH*b 1.938,0.667 2.854,0.865 0.917,0.198 10 false CANH*c 2.094,0.49 3.01,0.688 0.917,0.198 10 false CANH*d 2.26,0.323 3.177,0.521 0.917,0.198 10 false CANH*e 1.792,1.927 2.708,2.125 0.917,0.198 10 false CANL*b 1.969,2.094 2.885,2.292 0.917,0.198 10 false CANL*c 2.156,2.271 3.073,2.469 0.917,0.198 10 false CANL*d 2.323,2.448 3.24,2.646 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for Bus Buffer ECU (w/ Bus Buffer ECU)
*c for Central Gateway ECU (Network Gateway ECU) *d for Telephone Transceiver Assembly (w/ Telematics System)
*e for Central Gateway ECU (Network Gateway ECU) *f for Radio and Display Receiver Assembly (for Radio and Display Type)
*g for Position Control ECU Assembly (for RHD with Memory) *h for No. 1 CAN Junction Connector
*i for Headlight ECU Sub-assembly RH *j for Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. Wiring Color Connected to

*1: w/ Bus Buffer ECU

*2: w/ Telematics System

*3: for Radio and Display Type

*4: for RHD with Memory

G105-1 (CANH) LG Bus buffer ECU*1
G105-12 (CANL) W
G105-2 (CANH) B Central gateway ECU (network gateway ECU)
G105-13 (CANL) W
G105-3 (CANH) R Telephone transceiver assembly*2
G105-14 (CANL) W
G105-4 (CANH) G Central gateway ECU (network gateway ECU)
G105-15 (CANL) W
G105-5 (CANH) B Radio and display receiver assembly*3
G105-16 (CANL) W
G105-8 (CANH) G Position control ECU assembly*4
G105-19 (CANL) W
G105-9 (CANH) W No. 1 CAN junction connector
G105-20 (CANL) L
G105-10 (CANH) G Headlight ECU sub-assembly RH
G105-21 (CANL) W
G105-11 (CANH) LG Central gateway ECU (network gateway ECU)
G105-22 (CANL) W




NO. 6 CAN JUNCTION CONNECTOR


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C387413C59
0.365,1.271 0.771,1.5 0.406,0.229 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 2.167,0.375 2.333,0.375 2.333,0.375 3.313,1.302 true 2.219,2.417 2.385,2.417 2.385,2.417 3.313,1.573 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.427,1.302 0.792,1.458 0.365,0.156 10 false M31 1.365,0.583 1.917,0.76 0.552,0.177 10 false CANH*b 1.448,2 2,2.177 0.552,0.177 10 false CANL*b 1.583,0.302 2.135,0.479 0.552,0.177 10 false CANH*c 1.656,2.344 2.208,2.521 0.552,0.177 10 false CANL*c 4.99,0.188 5.698,0.427 0.708,0.24 10 false CANH*d 4.677,2.354 5.302,2.573 0.625,0.219 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for Occupant Detection ECU (w/ Occupant Classification System)
*c for Central Gateway ECU (Network Gateway ECU) *d for No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*: w/ Occupant Classification System

M31-2 (CANH) GR Occupant detection ECU*
M31-8 (CANL) W
M31-3 (CANH) G Central gateway ECU (network gateway ECU)
M31-9 (CANL) W
M31-4 (CANH) LG No. 1 CAN junction connector
M31-10 (CANL) W




NO. 7 CAN JUNCTION CONNECTOR


a.

Check the No. 7 CAN junction connector.

i.

Connection diagram

C387413C60
0.365,1.271 0.771,1.5 0.406,0.229 1.833,1.135 2,1.135 2,1.135 2.448,1.333 true 1.865,1.729 2.031,1.729 2.031,1.729 2.417,1.563 true 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 2.167,0.375 2.333,0.375 2.333,0.375 3.313,1.302 true 2.219,2.417 2.385,2.417 2.385,2.417 3.313,1.573 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 5.271,0.625 5.021,0.625 5.021,0.625 4.26,1.313 true 5.219,2.125 4.969,2.125 4.969,2.125 4.25,1.552 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.438,1.313 0.802,1.469 0.365,0.156 10 false N52 1.313,1.073 1.865,1.25 0.552,0.177 10 false CANH*b 1.354,1.667 1.906,1.844 0.552,0.177 10 false CANL*b 1.417,0.594 1.969,0.771 0.552,0.177 10 false CANH*c 1.469,1.979 2.021,2.156 0.552,0.177 10 false CANL*c 1.646,0.313 2.198,0.49 0.552,0.177 10 false CANH*d 1.719,2.354 2.271,2.531 0.552,0.177 10 false CANL*d 4.99,0.208 5.542,0.385 0.552,0.177 10 false CANH*e 4.677,2.385 5.229,2.563 0.552,0.177 10 false CANL*e 5.333,0.573 5.885,0.75 0.552,0.177 10 false CANH*f 5.292,2.073 5.844,2.25 0.552,0.177 10 false CANL*f
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 1 CAN Junction Connector
*c for Combination Meter Assembly *d for Multiplex Network Door ECU (w/ Power Back Door System)
*e for Position Control ECU Assembly (for LHD with Memory) *f for Headlight ECU Sub-assembly LH



ii.

Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Power Back Door System

*2: for LHD with Memory

N52-1 (CANH) B No. 1 CAN junction connector
N52-7 (CANL) W
N52-2 (CANH) LG Combination meter assembly
N52-8 (CANL) W
N52-3 (CANH) L Multiplex network door ECU*1
N52-9 (CANL) W
N52-4 (CANH) G Position control ECU assembly*2
N52-10 (CANL) W
N52-5 (CANH) P Headlight ECU sub-assembly LH
N52-11 (CANL) W




NO. 8 CAN JUNCTION CONNECTOR


a.

Check the No. 8 CAN junction connector.

i.

Connection diagram

C387413C61
0.365,1.271 0.771,1.5 0.406,0.229 1.833,1.135 2,1.135 2,1.135 2.448,1.333 true 1.865,1.729 2.031,1.729 2.031,1.729 2.417,1.563 true 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 2.167,0.375 2.333,0.375 2.333,0.375 3.313,1.302 true 2.219,2.417 2.385,2.417 2.385,2.417 3.313,1.573 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.427,1.323 0.792,1.479 0.365,0.156 10 false N53 1.313,1.073 1.865,1.25 0.552,0.177 10 false CANH*b 1.354,1.667 1.906,1.844 0.552,0.177 10 false CANL*b 1.417,0.594 1.969,0.771 0.552,0.177 10 false CANH*c 1.469,1.979 2.021,2.156 0.552,0.177 10 false CANL*c 1.646,0.313 2.198,0.49 0.552,0.177 10 false CANH*d 1.719,2.354 2.271,2.531 0.552,0.177 10 false CANL*d 4.99,0.208 5.542,0.385 0.552,0.177 10 false CANH*e 4.677,2.385 5.229,2.563 0.552,0.177 10 false CANL*e
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *d for Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)
*e for No. 1 CAN Junction Terminal - -



ii.

Check the connection diagram of the components which are connected to the No. 8 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Blind Spot Monitor System

*2: w/ Panoramic View Monitor System

*3: w/ Parking Assist Monitor System

N53-1 (CANH) SB No. 2 CAN junction connector
N53-7 (CANL) W
N53-2 (CANH) BE Blind spot monitor sensor LH*1
N53-8 (CANL) W
N53-3 (CANH) R Television camera assembly*2, *3
N53-9 (CANL) L
N53-4 (CANH) G No. 1 CAN junction terminal
N53-10 (CANL) W




NO. 1 CAN JUNCTION TERMINAL


a.

Check the No. 1 CAN junction terminal.

i.
C395263C06
2.75,0.833 3.167,1.083 0.417,0.25 1.115,0.375 1.281,0.375 1.281,0.375 1.698,0.875 true 0.667,1.479 0.833,1.479 0.833,1.479 1.333,1.063 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.604,0.292 1.177,0.479 0.573,0.188 10 false CANL*b 0.156,1.396 0.688,1.573 0.531,0.177 10 false CANH*b 2.833,0.875 3.292,1.073 0.458,0.198 10 false N54
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b for No. 8 CAN Junction Connector


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
N54-3 (CANH) G No. 8 CAN junction connector
N54-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C391595C09
1.625,1.313 2.042,1.583 0.417,0.271 3.865,1.125 3.865,0.51 3.865,0.51 4.052,0.51 true 3.51,1.125 3.51,0.51 3.51,0.51 3.313,0.51 true 4.417,2.24 4.229,2.24 4.229,2.24 4.229,1.708 true 3.667,2.24 3.865,2.24 3.865,2.24 3.865,1.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.458 4.792,0.688 0.635,0.229 10 false CANH 3.26,2.198 3.896,2.427 0.635,0.229 10 false CANL 3.042,0.469 3.677,0.698 0.635,0.229 10 false CG 4.51,2.177 5.146,2.406 0.635,0.229 10 false BAT 1.677,1.375 2.313,1.604 0.635,0.229 10 false G114
*a Front view of DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G114-6 (CANH) - G114-14 (CANL) B - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G114-6 (CANH) - G114-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G114-14 (CANL) - G114-4 (CG) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G114-6 (CANH) - G114-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G114-14 (CANL) - G114-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C70
1.083,1.281 1.5,1.552 0.417,0.271 3.615,2.51 3.448,2.51 3.448,2.51 3.448,1.427 true 3.552,2.667 3.365,2.667 3.365,2.667 3.365,1.427 true 3.24,1.292 3.24,0.26 3.24,0.26 3.125,0.26 true 2.885,2.24 3.031,2.24 3.031,2.24 3.031,1.438 true 3.542,1.375 3.542,0.51 3.542,0.51 3.698,0.51 true 3.115,2.615 3.281,2.615 3.281,2.615 3.281,1.427 true 3.042,2.438 3.198,2.438 3.198,2.438 3.198,1.438 true 3.156,1.302 3.156,0.438 3.156,0.438 3.01,0.438 true 3.073,1.302 3.073,0.594 3.073,0.594 2.917,0.594 true 3.625,1.385 3.625,0.667 3.625,0.667 3.781,0.667 true 3.885,2.354 3.719,2.354 3.719,2.354 3.719,1.438 true 3.958,2.188 3.792,2.188 3.792,2.188 3.792,1.427 true 4.042,2 3.875,2 3.875,2 3.875,1.427 true 3.917,1.292 3.917,0.854 3.917,0.854 4.073,0.854 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.469,2.177 2.958,2.354 0.49,0.177 10 false CA1H 2.542,0.542 3.094,0.76 0.552,0.219 10 false CA1L 2.646,0.385 3.198,0.604 0.552,0.219 10 false CA2L 2.656,2.375 3.146,2.552 0.49,0.177 10 false CA2H 2.75,0.198 3.24,0.375 0.49,0.177 10 false CA3H 2.75,2.563 3.302,2.781 0.552,0.219 10 false CA3L 3.688,2.448 4.177,2.625 0.49,0.177 10 false CAYH 3.625,2.604 4.115,2.781 0.49,0.177 10 false CAYL 3.771,0.448 4.26,0.625 0.49,0.177 10 false CA4H 4.135,0.792 4.688,1.01 0.552,0.219 10 false CA6L 4.031,2.125 4.521,2.302 0.49,0.177 10 false CA5H 3.969,2.292 4.521,2.51 0.552,0.219 10 false CA5L 1.188,1.354 1.635,1.615 0.448,0.26 10 false G72 4.115,1.938 4.604,2.115 0.49,0.177 10 false CA6H 3.854,0.604 4.406,0.823 0.552,0.219 10 false CA4L
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.

C349820C47
1.094,1.708 1.5,1.979 0.406,0.271 4.427,1.74 4.427,0.917 4.427,0.917 4.583,0.917 true 4.271,1.74 4.271,0.698 4.271,0.698 4.427,0.698 true 4.125,1.74 4.125,0.458 4.125,0.458 4.281,0.458 true 4.208,1.979 4.208,3.021 4.208,3.021 4.365,3.021 true 4.052,1.99 4.052,3.281 4.052,3.281 4.208,3.281 true 4.51,1.99 4.51,2.813 4.51,2.813 4.667,2.813 true 3.906,1.99 3.906,3.448 3.906,3.448 3.74,3.448 true 3.76,1.979 3.76,3.271 3.76,3.271 3.604,3.271 true 3.604,1.885 3.604,0.458 3.604,0.458 3.448,0.458 true 3.458,1.885 3.458,0.646 3.458,0.646 3.302,0.646 true 3.313,1.99 3.313,3.052 3.313,3.052 3.156,3.052 true 3.156,1.99 3.156,2.875 3.156,2.875 3,2.875 true 2.938,1.75 2.938,0.948 2.938,0.948 2.781,0.948 true 3.01,1.969 3.01,2.604 3.01,2.604 2.854,2.604 true 2.333,1.771 2.333,1.167 2.333,1.167 2.177,1.167 true 4.781,1.802 5.229,1.802 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.177,1.771 1.552,1.979 0.375,0.208 10 false G72 4.74,2.75 5.698,3.031 0.958,0.281 10 false CA1H 4.667,0.854 5.625,1.135 0.958,0.281 10 false CA1L 4.458,2.958 5.417,3.24 0.958,0.281 10 false CA2H 4.385,0.406 5.344,0.688 0.958,0.281 10 false CA3H 3.031,0.396 3.99,0.677 0.958,0.281 10 false CA4H 2.594,2.823 3.552,3.104 0.958,0.281 10 false CA5H 3.177,3.219 4.135,3.5 0.958,0.281 10 false CAYH 4.51,0.646 5.469,0.927 0.958,0.281 10 false CA2L 4.292,3.219 5.25,3.5 0.958,0.281 10 false CA3L 2.906,0.594 3.865,0.875 0.958,0.281 10 false CA4L 2.792,3 3.75,3.281 0.958,0.281 10 false CA5L 3.365,3.396 4.323,3.677 0.958,0.281 10 false CAYL 2.458,2.542 3.417,2.823 0.958,0.281 10 false CA6H 2.396,0.896 3.354,1.177 0.958,0.281 10 false CA6L 1.771,1.104 2.729,1.385 0.958,0.281 10 false BATT 5.302,1.74 5.865,1.99 0.563,0.25 10 false GND
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines (DLC3 - Central Gateway ECU [Network Gateway ECU])
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-14 (CA6H) - G72-5 (CA6L) B - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G72-14 (CA6H) - G72-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-5 (CA6L) - G72-10 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-14 (CA6H) - G72-1 (BATT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-5 (CA6L) - G72-1 (BATT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-23 (CA1H) - G72-8 (CA1L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G72-23 (CA1H) - G72-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-8 (CA1L) - G72-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-23 (CA1H) - G72-1 (BATT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-8 (CA1L) - G72-1 (BATT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-18 (CA4H) - G72-17 (CA4L) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G72-18 (CA4H) - G72-10 (GND) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-17 (CA4L) - G72-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-18 (CA4H) - G72-1 (BATT) SB - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-17 (CA4L) - G72-1 (BATT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-19 (CAYH) - G72-20 (CAYL) G - W HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G72-19 (CAYH) - G72-6 (CA3H) G - B HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G72-20 (CAYL) - G72-21 (CA3L) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G72-19 (CAYH) - G72-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-20 (CAYL) - G72-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-19 (CAYH) - G72-1 (BATT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-20 (CAYL) - G72-1 (BATT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-22 (CA2H) - G72-7 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G72-22 (CA2H) - G72-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-7 (CA2L) - G72-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-22 (CA2H) - G72-1 (BATT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-7 (CA2L) - G72-1 (BATT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G72-15 (CA5H) - G72-16 (CA5L) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G72-15 (CA5H) - G72-10 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-16 (CA5L) - G72-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-15 (CA5H) - G72-1 (BATT) LG - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G72-16 (CA5L) - G72-1 (BATT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.

for A25A-FKS with Canister Pump Module: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>TERMINALS OF ECM

for A25A-FKS without Canister Pump Module: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>TERMINALS OF ECM

for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C405888C04
1.417,0.167 1.813,0.417 0.396,0.25 2.406,1.385 2.802,0.604 2.802,0.604 2.969,0.604 true 1.052,1.313 0.688,0.594 0.688,0.594 0.521,0.594 true 1.781,1.427 0.979,0.406 0.979,0.406 0.813,0.406 true 1.813,1.302 1.01,0.188 1.01,0.188 0.844,0.188 true 1.49,0.208 1.948,0.406 0.458,0.198 10 false A24 0.104,0.063 0.563,0.26 0.458,0.198 10 false *a 3.052,0.542 3.375,0.76 0.323,0.219 10 false E1 0.115,0.521 0.573,0.719 0.458,0.198 10 false BATT 0.427,0.344 0.885,0.542 0.458,0.198 10 false CANL 0.448,0.115 0.906,0.313 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-8 (CANH) - A24-18 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A24-8 (CANH) - A24-10 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-18 (CANL) - A24-10 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-8 (CANH) - A24-1 (BATT) B - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-18 (CANL) - A24-1 (BATT) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ENGINE STOP AND START ECU


Refer to Terminals of ECU.

for A25A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>TERMINALS OF ECU

for M20A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the engine stop and start ECU connectors.

C382798C04
1,0.188 1.417,0.427 0.417,0.24 3.323,0.156 3.74,0.396 0.417,0.24 5.188,0.104 5.604,0.344 0.417,0.24 6.219,0.104 6.635,0.344 0.417,0.24 0.344,0.885 0.438,1.417 0.438,1.417 0.604,1.417 true 4.042,0.99 4.344,0.385 4.344,0.385 4.51,0.385 true 5.188,1.104 4.896,1.385 4.896,1.385 4.74,1.385 true 5.292,1.104 5.031,1.583 5.031,1.583 4.875,1.583 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.094,0.229 1.406,0.427 0.313,0.198 10 false A34 3.427,0.208 3.74,0.406 0.313,0.198 10 false A33 5.271,0.135 5.583,0.333 0.313,0.198 10 false A32 0.656,1.365 0.969,1.563 0.313,0.198 10 false +B 4.271,1.313 4.75,1.51 0.479,0.198 10 false CANH 6.323,0.146 6.635,0.344 0.313,0.198 10 false G62 5.677,0.156 5.99,0.354 0.313,0.198 10 false *A 6.698,0.146 7.01,0.344 0.313,0.198 10 false *B 4.458,1.521 4.938,1.719 0.479,0.198 10 false CANL 4.594,0.323 5.073,0.521 0.479,0.198 10 false GND1
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A32-13 (CANH) - A32-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A32-13 (CANH) - A33-8 (GND1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A32-14 (CANL) - A33-8 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A32-13 (CANH) - A34-1 (+B) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A32-14 (CANL) - A34-1 (+B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G62-13 (CANH) - G62-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G62-13 (CANH) - A33-8 (GND1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G62-14 (CANL) - A33-8 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G62-13 (CANH) - A34-1 (+B) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G62-14 (CANL) - A34-1 (+B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TRANSMISSION CONTROL ECU (for CVT)


Refer to Terminals of ECU.

for K120: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU

for K120F: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C392554C15
1.583,0.188 2,0.438 0.417,0.25 1.979,1.896 2.333,0.979 true 2.885,1.885 2.417,0.99 true 0.396,1.646 0.938,1.031 true 0.625,1.896 1.063,1.031 true 0.156,0.146 0.417,0.385 0.26,0.24 10 false *a 1.677,0.229 2.083,0.479 0.406,0.25 10 false C33 2.948,1.823 3.385,2.073 0.438,0.25 10 false CANL 1.552,1.823 1.99,2.073 0.438,0.25 10 false CANH 0.417,1.823 0.729,2.021 0.313,0.198 10 false E1 0.156,1.594 0.469,1.792 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Transmission Control ECU)


Disconnect the transmission control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C33-15 (CANH) - C33-16 (CANL) GR - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C33-15 (CANH) - C33-2 (E1) GR - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C33-16 (CANL) - C33-2 (E1) P - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C33-15 (CANH) - C33-1 (+B) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C33-16 (CANL) - C33-1 (+B) P - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.

C380240C25
1.448,0.698 1.885,0.948 0.438,0.25 3.083,1.583 3.25,1.583 3.25,1.583 3.333,1 true 2.667,1.417 2.833,1.417 2.833,1.417 3.271,0.875 true 2.073,1.177 2.24,1.177 2.24,1.177 2.625,0.958 true 5.063,0.542 4.896,0.542 4.896,0.542 4.552,0.771 true 0.146,0.094 0.458,0.25 0.313,0.156 10 false *a 1.542,0.74 2,0.938 0.458,0.198 10 false A39 2.271,1.333 2.729,1.531 0.458,0.198 10 false CANL 2.646,1.51 3.104,1.708 0.458,0.198 10 false CANH 1.729,1.104 2.188,1.302 0.458,0.198 10 false +BM 5.125,0.469 5.583,0.667 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A39-5 (CANH) - A39-19 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A39-5 (CANH) - A39-46 (GND1) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A39-19 (CANL) - A39-46 (GND1) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A39-5 (CANH) - A39-1 (+BM) P - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A39-19 (CANL) - A39-1 (+BM) V - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RACK AND PINION POWER STEERING GEAR ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406383C08
1.531,0.375 1.865,0.573 0.333,0.198 1.542,2.875 1.979,3.083 0.438,0.208 1.125,2.323 1.292,2.323 1.292,2.323 1.292,1.74 true 1.542,2.552 1.708,2.552 1.708,2.552 1.708,1.885 true 1.979,2.542 1.813,2.542 1.813,2.542 1.813,1.875 true 2.552,4.208 2.385,4.208 2.385,4.208 2.219,3.792 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 0.292,2.75 0.604,2.948 0.313,0.198 10 false *b 0.688,2.26 1.271,2.438 0.583,0.177 10 false PGND 1.573,0.396 2.156,0.573 0.583,0.177 10 false C54 1.135,2.49 1.719,2.667 0.583,0.177 10 false CANH 2.052,2.469 2.635,2.646 0.583,0.177 10 false CANL 2.615,4.146 3.198,4.323 0.583,0.177 10 false BAT 1.594,2.906 2.177,3.083 0.583,0.177 10 false G114
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
*b Front view of DLC3


Disconnect the rack and pinion power steering gear assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for A25A-FKS and 4WD/AWD

*2: except A25A-FKS and 4WD/AWD

C54-10 (CANH) - C54-11 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C54-10 (CANH) - C54-7 (PGND) G - W-L*1
G - B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C54-11 (CANL) - C54-7 (PGND) W - W-L*1
W - B*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C54-10 (CANH) - G114-16 (BAT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C54-11 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C358931C08
4.698,0.917 5.094,1.115 0.396,0.198 5.667,0.885 5.667,0.469 5.667,0.469 5.917,0.469 true 5.677,1.198 5.677,1.531 5.677,1.531 5.927,1.531 true 4.667,0.177 4.979,0.375 0.313,0.198 10 false *a 4.76,0.948 5.073,1.146 0.313,0.198 10 false G68 5.979,0.406 6.458,0.594 0.479,0.188 10 false CANH 5.99,1.479 6.469,1.667 0.479,0.188 10 false CANL
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369124C58
0.552,1.615 1.073,1.865 0.521,0.25 1,0.75 1.25,0.75 1.25,0.75 1.667,1.75 true 1.083,2.667 1.333,2.667 1.333,2.667 1.667,2 true 2.302,0.771 2.052,0.771 2.052,0.771 1.885,1.688 true 0.667,2.25 0.917,2.25 0.917,2.25 1.333,2 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.677,1.667 1.104,1.875 0.427,0.208 10 false G68 0.604,0.688 1.063,0.885 0.458,0.198 10 false CANH 0.708,2.594 1.167,2.792 0.458,0.198 10 false CANL 2.375,0.688 2.833,0.885 0.458,0.198 10 false BAT 0.344,2.177 0.802,2.375 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for LHD and Manual Transaxle

*2: except LHD and Manual Transaxle

G68-3 (CANH) - G68-8 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G68-3 (CANH) - G68-6 (ESS) G - W-B*1
G - LA*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-8 (CANL) - G68-6 (ESS) W - W-B*1
W - LA*2
LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-3 (CANH) - G68-4 (BAT) G - LA-B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-8 (CANL) - G68-4 (BAT) W - LA-B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Pre-collision System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connector.

C406374C08
1.823,0.146 2.146,0.396 0.323,0.25 4.979,0.198 5.385,0.469 0.406,0.271 2.219,1.688 2.219,2.125 2.219,2.125 2.375,2.125 true 2.219,1.323 2.219,0.583 2.219,0.583 2.375,0.583 true 2.063,1.688 2.063,2.125 2.063,2.125 1.927,2.125 true 5.844,1.677 5.844,2.073 5.844,2.073 6,2.073 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *b 1.917,0.198 2.229,0.396 0.313,0.198 10 false P8 2.458,0.51 2.927,0.729 0.469,0.219 10 false CA1P 2.458,2.063 2.927,2.281 0.469,0.219 10 false CA1N 1.573,2.063 2.042,2.281 0.469,0.219 10 false GND 5.021,0.26 5.51,0.604 0.49,0.344 10 false G114 6.083,2.01 6.552,2.229 0.469,0.219 10 false BAT
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P8-5 (CA1P) - P8-11 (CA1N) L - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
P8-5 (CA1P) - P8-10 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P8-11 (CA1N) - P8-10 (GND) B - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
P8-5 (CA1P) - G114-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P8-11 (CA1N) - G114-16 (BAT) B - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.

C406375C08
4.99,0.208 5.458,0.49 0.469,0.281 1.74,0.115 2.104,0.385 0.365,0.271 2.073,1.26 2.073,0.573 2.073,0.573 2.229,0.573 true 1.906,1.26 1.906,0.573 1.906,0.573 1.729,0.573 true 0.99,1.344 1.688,1.344 true 5.979,2.073 5.823,2.073 5.823,2.073 5.833,1.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 1.323,0.51 1.802,0.719 0.479,0.208 10 false CA2L 2.354,0.521 2.833,0.729 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.094,2.01 6.573,2.219 0.479,0.208 10 false BAT 5.063,0.281 5.5,0.51 0.438,0.229 10 false G114 1.844,0.177 2.167,0.375 0.323,0.198 10 false B9
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B9-3 (CA2H) - B9-2 (CA2L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B9-3 (CA2H) - B9-1 (SGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B9-2 (CA2L) - B9-1 (SGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B9-3 (CA2H) - G114-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B9-2 (CA2L) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>TERMINALS OF ECU

w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the airbag sensor assembly connector.

C409697C01
2.083,0.25 2.5,0.5 0.417,0.25 5.469,0.625 5.885,0.875 0.417,0.25 2.688,1.479 3,0.5 3,0.5 3.167,0.5 true 2.792,1.469 3.083,0.865 3.083,0.865 3.25,0.865 true 6.104,1.583 6.302,1.813 6.302,1.813 6.469,1.813 true 2.469,1.802 2.917,2.292 2.917,2.292 3.083,2.292 true 1.135,0.458 1.448,0.656 0.313,0.198 10 false *a 4.719,0.844 5.031,1.042 0.313,0.198 10 false *b 2.167,0.281 2.479,0.479 0.313,0.198 10 false G70 5.51,0.667 5.948,0.896 0.438,0.229 10 false G114 3.271,0.438 3.823,0.667 0.552,0.229 10 false CANH 3.313,0.802 3.865,1.031 0.552,0.229 10 false CANL 6.552,1.76 7.104,1.99 0.552,0.229 10 false BAT 3.146,2.219 3.698,2.448 0.552,0.229 10 false E1
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G70-26 (CANH) - G70-27 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G70-26 (CANH) - G70-33 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-27 (CANL) - G70-33 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-26 (CANH) - G114-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G70-27 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406366C10
1.5,0.125 1.885,0.385 0.385,0.26 2.771,1.188 2.917,0.333 2.917,0.333 3.083,0.333 true 0.896,1.198 1.313,1.813 1.313,1.813 1.479,1.813 true 0.542,1.833 0.75,1.833 0.75,1.833 0.635,1.375 true 0.906,1.427 1.323,2.042 1.323,2.042 1.49,2.042 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.604,0.198 1.917,0.354 0.313,0.156 10 false G18 0.365,1.771 0.844,1.927 0.479,0.156 10 false ES 1.552,1.948 2.156,2.177 0.604,0.229 10 false CANL 3.135,0.281 3.427,0.479 0.292,0.198 10 false B 1.531,1.729 2.135,1.958 0.604,0.229 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G18-9 (CANH) - G18-25 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G18-9 (CANH) - G18-23 (ES) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G18-25 (CANL) - G18-23 (ES) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G18-9 (CANH) - G18-22 (B) B - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G18-25 (CANL) - G18-22 (B) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406389C07
1.438,0.156 1.885,0.375 0.448,0.219 1.448,2.552 1.958,2.781 0.51,0.229 1.833,0.594 2,0.594 2,0.594 2.333,1.094 true 2.302,0.594 2.135,0.594 2.135,0.594 2.469,1.094 true 1.125,2.688 1.292,2.688 1.292,2.688 1.625,3.188 true 1.792,4.135 1.958,4.135 1.958,4.135 2.208,3.635 true 0.208,0.271 0.521,0.469 0.313,0.198 10 false *a 0.344,2.74 0.656,2.938 0.313,0.198 10 false *b 1.563,0.198 1.875,0.396 0.313,0.198 10 false G44 1.542,2.583 2.063,2.781 0.521,0.198 10 false G114 1.417,0.531 1.927,0.729 0.51,0.198 10 false CANL 2.365,0.542 2.875,0.74 0.51,0.198 10 false CANH 0.875,2.625 1.385,2.823 0.51,0.198 10 false CG 1.49,4.063 2,4.26 0.51,0.198 10 false BAT
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3


Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G44-5 (CANH) - G44-4 (CANL) BE - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G44-5 (CANH) - G114-4 (CG) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G44-4 (CANL) - G114-4 (CG) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G44-5 (CANH) - G114-16 (BAT) BE - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G44-4 (CANL) - G114-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connectors.

C405922C01
3.573,0.073 3.99,0.323 0.417,0.25 0.979,0.083 1.396,0.333 0.417,0.25 5.917,0.167 6.333,0.417 0.417,0.25 3.052,0.74 2.802,0.333 2.802,0.333 2.635,0.333 true 1.25,0.969 0.833,1.583 0.833,1.583 0.667,1.583 true 1.375,0.979 1.417,1.583 1.417,1.583 1.583,1.583 true 6.615,1.167 6.271,1.573 6.271,1.573 6.104,1.573 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 3.688,0.125 4,0.323 0.313,0.198 10 false G3 1.094,0.135 1.406,0.333 0.313,0.198 10 false G2 2.198,0.26 2.667,0.479 0.469,0.219 10 false GND1 5.792,1.51 6.26,1.698 0.469,0.188 10 false BAT 0.219,1.51 0.688,1.698 0.469,0.188 10 false CANH 1.656,1.5 2.125,1.688 0.469,0.188 10 false CANL 5.969,0.219 6.448,0.417 0.479,0.198 10 false G114 5.208,0.198 5.521,0.396 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G2-13 (CANH) - G2-14 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G2-13 (CANH) - G3-1 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G2-14 (CANL) - G3-1 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G2-13 (CANH) - G114-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G2-14 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the telephone transceiver assembly connector.

C409698C03
5.469,0.625 5.854,0.875 0.385,0.25 1.875,0.344 2.26,0.594 0.385,0.25 2.188,1.396 2.625,0.208 2.625,0.208 2.792,0.208 true 2.313,1.375 2.781,0.438 2.781,0.438 2.948,0.438 true 6.083,1.594 6.104,2.135 6.104,2.135 6.271,2.135 true 2.635,1.219 3.333,0.792 3.333,0.792 3.5,0.792 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.969,0.375 2.281,0.573 0.313,0.198 10 false H6 5.51,0.656 5.958,0.885 0.448,0.229 10 false G114 4.854,0.823 5.167,1.021 0.313,0.198 10 false *b 2.865,0.146 3.406,0.354 0.542,0.208 10 false CANP 3.01,0.344 3.552,0.552 0.542,0.208 10 false CANN 6.365,2.073 6.906,2.281 0.542,0.208 10 false BAT 3.604,0.729 4.146,0.938 0.542,0.208 10 false E
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H6-15 (CANP) - H6-16 (CANN) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H6-15 (CANP) - H6-4 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H6-16 (CANN) - H6-4 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H6-15 (CANP) - G114-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H6-16 (CANN) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
B532755C04
1.583,0.333 2.01,0.604 0.427,0.271 1.115,1.135 0.802,0.594 0.802,0.594 0.615,0.594 true 1.25,1.188 0.729,1.896 0.729,1.896 0.542,1.896 true 2.875,0.469 2.74,0.469 2.74,0.469 2.552,1.292 true 1.052,1.292 0.781,1.021 0.781,1.021 0.594,1.021 true 1.667,0.385 2.125,0.583 0.458,0.198 10 false G46 0.24,0.521 0.698,0.719 0.458,0.198 10 false CANL 0.135,1.813 0.594,2.01 0.458,0.198 10 false CANH 0.135,0.073 0.594,0.271 0.458,0.198 10 false *a 2.927,0.406 3.385,0.604 0.458,0.198 10 false GND 0.438,0.948 0.896,1.146 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G46-2 (CANH) - G46-1 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G46-2 (CANH) - G46-17 (GND) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-1 (CANL) - G46-17 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-2 (CANH) - G46-5 (B) SB - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G46-1 (CANL) - G46-5 (B) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the television camera assembly connector.

C409699C01
1.917,0.333 2.333,0.583 0.417,0.25 5.135,0.531 5.552,0.781 0.417,0.25 1.333,2.167 1.5,2.167 1.5,2.167 1.875,1.646 true 1.146,0.865 1.313,0.865 1.313,0.865 1.896,1.323 true 5.844,1.604 6.208,2.031 6.208,2.031 6.375,2.031 true 5.219,1.188 5.875,0.729 5.875,0.729 6.042,0.729 true 0.927,0.354 1.24,0.552 0.313,0.198 10 false *a 4.146,0.688 4.458,0.885 0.313,0.198 10 false *b 2.01,0.375 2.5,0.573 0.49,0.198 10 false R15 5.167,0.573 5.656,0.771 0.49,0.198 10 false G114 0.615,0.781 1.104,0.979 0.49,0.198 10 false CANL 0.885,2.073 1.375,2.271 0.49,0.198 10 false CANH 6.51,1.958 7,2.156 0.49,0.198 10 false BAT 6.104,0.667 6.594,0.865 0.49,0.198 10 false CG
*a Front view of wire harness connector
(to Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R15-4 (CANH) - R15-1 (CANL) R - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R15-4 (CANH) - G114-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R15-1 (CANL) - G114-4 (CG) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R15-4 (CANH) - G114-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R15-1 (CANL) - G114-16 (BAT) L - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.

w/ Parking Support Brake System: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (for Gasoline Model with Parking Support Brake System)>TERMINALS OF ECU

w/o Parking Support Brake System: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Parking Support Brake System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.

C406371C09
1.688,0.188 2.104,0.458 0.417,0.271 5.073,0.177 5.49,0.448 0.417,0.271 1.688,0.542 2.104,0.813 0.417,0.271 2.938,1.25 2.938,0.333 2.938,0.333 3.073,0.333 true 3.063,1.25 3.063,0.563 3.063,0.563 3.198,0.563 true 6.063,2.073 5.927,2.073 5.927,2.073 5.927,1.646 true 5.24,1.115 5.24,0.688 5.24,0.688 5.375,0.688 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.917,0.115 4.229,0.313 0.313,0.198 10 false *b 3.146,0.26 3.458,0.458 0.313,0.198 10 false R1 3.281,0.49 3.594,0.688 0.313,0.198 10 false R2 1.792,0.594 2.177,0.865 0.385,0.271 10 false H4 5.458,0.625 5.771,0.823 0.313,0.198 10 false CG 6.135,2 6.656,2.208 0.521,0.208 10 false BAT 5.115,0.229 5.677,0.51 0.563,0.281 10 false G114 1.771,0.24 2.156,0.51 0.385,0.271 10 false G25 2.188,0.24 2.5,0.438 0.313,0.198 10 false *A 2.188,0.594 2.5,0.792 0.313,0.198 10 false *B
*A for LHD and Manual Transaxle *B except LHD and Manual Transaxle
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and Manual Transaxle
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G25-17 (R1) - G25-18 (R2) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G25-17 (R1) - G114-4 (CG) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-18 (R2) - G114-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-17 (R1) - G114-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G25-18 (R2) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

except LHD and Manual Transaxle
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H4-17 (R1) - H4-18 (R2) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H4-17 (R1) - G114-4 (CG) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H4-18 (R2) - G114-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H4-17 (R1) - G114-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H4-18 (R2) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.

C406372C12
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 1.76,1.302 1.76,0.615 1.76,0.615 1.604,0.615 true 1.615,2.219 1.76,2.219 1.76,2.219 1.76,1.563 true 2.375,2.219 2.219,2.219 2.219,2.219 2.219,1.563 true 6,2.115 5.844,2.115 5.844,2.115 5.844,1.667 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *b 1.833,0.198 2.156,0.396 0.323,0.198 10 false Q1 5.042,0.292 5.625,0.5 0.583,0.208 10 false G114 1.198,2.156 1.688,2.406 0.49,0.25 10 false CA1N 1.177,0.552 1.667,0.802 0.49,0.25 10 false CA1P 2.448,2.156 3.031,2.375 0.583,0.219 10 false BLGD 6.083,2.052 6.573,2.302 0.49,0.25 10 false BAT
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q1-2 (CA1P) - Q1-7 (CA1N) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q1-2 (CA1P) - Q1-10 (BLGD) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q1-7 (CA1N) - Q1-10 (BLGD) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q1-2 (CA1P) - G114-16 (BAT) V - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q1-7 (CA1N) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369116C14
1.5,0.167 1.917,0.417 0.417,0.25 1.094,1.438 1.25,0.833 1.25,0.833 1.417,0.833 true 0.938,1.427 1.115,0.667 1.115,0.667 1.281,0.667 true 2.49,1.427 2.646,0.823 2.646,0.823 2.813,0.823 true 0.927,1.948 1.365,2.635 1.365,2.635 1.531,2.635 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.604,0.208 1.917,0.406 0.313,0.198 10 false G54 1.333,0.604 1.792,0.802 0.458,0.198 10 false CANH 1.469,0.781 1.927,0.979 0.458,0.198 10 false CANL 2.875,0.74 3.333,0.938 0.458,0.198 10 false +B 1.573,2.552 2.031,2.75 0.458,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G54-1 (CANH) - G54-2 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G54-1 (CANH) - G54-18 (E) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G54-2 (CANL) - G54-18 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G54-1 (CANH) - G54-4 (+B) G - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G54-2 (CANL) - G54-4 (+B) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY LH


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406391C13
1.479,2.375 1.938,2.604 0.458,0.229 1.479,0.177 1.938,0.406 0.458,0.229 2.656,2.198 2.49,2.198 2.49,2.198 2.656,1.615 true 2.198,2.188 2.365,2.188 2.365,2.188 2.531,1.604 true 0.854,2.188 1.021,2.188 1.021,2.188 0.854,1.604 true 2.083,4.25 2.25,4.25 2.25,4.25 2.417,3.667 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 1.583,0.219 1.896,0.417 0.313,0.198 10 false A11 1.563,2.406 2.156,2.594 0.594,0.188 10 false G114 2.708,2.125 3.177,2.323 0.469,0.198 10 false CANH 1.792,2.104 2.26,2.302 0.469,0.198 10 false CANL 0.51,2.104 0.979,2.302 0.469,0.198 10 false GND 1.771,4.177 2.24,4.375 0.469,0.198 10 false BAT
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A11-24 (CANH) - A11-23 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A11-24 (CANH) - A11-12 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A11-23 (CANL) - A11-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A11-24 (CANH) - G114-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A11-23 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY RH


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406391C14
1.479,2.375 1.938,2.604 0.458,0.229 1.479,0.177 1.938,0.406 0.458,0.229 2.656,2.198 2.49,2.198 2.49,2.198 2.656,1.615 true 2.198,2.188 2.365,2.188 2.365,2.188 2.531,1.604 true 0.854,2.188 1.021,2.188 1.021,2.188 0.854,1.604 true 2.083,4.25 2.25,4.25 2.25,4.25 2.417,3.667 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 1.583,0.219 1.896,0.417 0.313,0.198 10 false A12 1.563,2.406 2.24,2.625 0.677,0.219 10 false G114 2.708,2.125 3.177,2.323 0.469,0.198 10 false CANH 1.792,2.104 2.26,2.302 0.469,0.198 10 false CANL 0.51,2.104 0.979,2.302 0.469,0.198 10 false GND 1.771,4.177 2.24,4.375 0.469,0.198 10 false BAT
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A12-24 (CANH) - A12-23 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A12-24 (CANH) - A12-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A12-23 (CANL) - A12-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A12-24 (CANH) - G114-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A12-23 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY (w/ Memory)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C371309C12
1.021,0.104 1.427,0.333 0.406,0.229 0.167,2.24 0.573,2.469 0.406,0.229 2,0.094 2.406,0.323 0.406,0.229 0.167,2.656 0.573,2.885 0.406,0.229 1.094,2.021 1.26,2.021 1.26,2.021 1.427,2.354 true 2.333,2 2.167,2 2.167,2 2,2.333 true 2.885,0.521 2.719,0.521 2.719,0.521 2.604,0.917 true 2.854,1.427 2.688,1.427 2.688,1.427 2.469,1.021 true 1.146,0.135 1.458,0.333 0.313,0.198 10 false T8 0.292,2.271 0.604,2.469 0.313,0.198 10 false T7 0.75,1.938 1.146,2.115 0.396,0.177 10 false GND 2.375,1.917 2.771,2.094 0.396,0.177 10 false +B 2.948,1.344 3.427,1.542 0.479,0.198 10 false CANP 2.948,0.438 3.427,0.635 0.479,0.198 10 false CANN 0.063,0.063 0.458,0.24 0.396,0.177 10 false *a 1.469,0.135 1.865,0.313 0.396,0.177 10 false *A 2.125,0.125 2.438,0.323 0.313,0.198 10 false S8 2.458,0.125 2.854,0.302 0.396,0.177 10 false *B 0.281,2.688 0.594,2.885 0.313,0.198 10 false S7 0.625,2.281 1.021,2.458 0.396,0.177 10 false *A 0.646,2.698 1.042,2.875 0.396,0.177 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU Assembly)


Disconnect the position control ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T8-13 (CANP) - T8-14 (CANN) LG - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
T8-13 (CANP) - T7-2 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T8-14 (CANN) - T7-2 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T8-13 (CANP) - T7-3 (+B) LG - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T8-14 (CANN) - T7-3 (+B) R - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S8-13 (CANP) - S8-14 (CANN) LG - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S8-13 (CANP) - S7-2 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S8-14 (CANN) - S7-2 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S8-13 (CANP) - S7-3 (+B) LG - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S8-14 (CANN) - S7-3 (+B) R - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BUS BUFFER ECU (w/ Bus Buffer ECU)


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C409700C01
1.458,2.5 1.958,2.75 0.5,0.25 1.458,0.167 1.958,0.417 0.5,0.25 1.625,3.135 1,2.667 true 2.75,4.25 2.281,3.604 true 0.938,1.979 1.354,1.229 true 1.969,1.958 1.552,1.208 true 0.167,2.479 0.479,2.635 0.313,0.156 10 false *b 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 0.719,2.615 1.333,2.813 0.615,0.198 10 false CG 1.875,2.031 2.49,2.229 0.615,0.198 10 false CAN+ 0.719,2.031 1.333,2.229 0.615,0.198 10 false CAN- 1.573,2.552 2.188,2.75 0.615,0.198 10 false G114 1.594,0.219 2.208,0.417 0.615,0.198 10 false G80 2.698,4.281 3.313,4.479 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Bus Buffer ECU)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G80-2 (CAN+) - G80-1 (CAN-) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-2 (CAN+) - G114-4 (CG) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-1 (CAN-) - G114-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-2 (CAN+) - G114-16 (BAT) LG - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-1 (CAN-) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY (for 4WD/AWD with Dynamic Torque Control 4WD/AWD System)


Refer to Terminals of ECU.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connectors.

C409701C01
2,0.333 2.417,0.583 0.417,0.25 4.99,0.292 5.406,0.542 0.417,0.25 5.875,1.521 6.167,0.5 6.167,0.5 6.333,0.5 true 5.875,1.802 6.167,2.25 6.167,2.25 6.333,2.25 true 0.979,1.115 1.146,1.115 1.146,1.115 1.656,1.375 true 1.948,1.208 2.802,0.552 2.802,0.552 2.969,0.552 true 0.156,0.052 0.469,0.25 0.313,0.198 10 false *a 2.115,0.385 2.427,0.583 0.313,0.198 10 false N3 5.125,0.344 5.438,0.542 0.313,0.198 10 false N4 0.615,1.073 1.01,1.25 0.396,0.177 10 false GND 6.417,0.427 6.948,0.646 0.531,0.219 10 false CANH 6.396,2.177 6.927,2.396 0.531,0.219 10 false CANL 3.063,0.49 3.594,0.708 0.531,0.219 10 false BSLC
*a Front view of wire harness connector
(to 4WD ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N4-17 (CANH) - N4-26 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
N4-17 (CANH) - N3-1 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N4-26 (CANL) - N3-1 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N4-17 (CANH) - N3-2 (BSLC) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N4-26 (CANL) - N3-2 (BSLC) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY (for 4WD/AWD with Dynamic Torque Vectoring AWD System)


Refer to Terminals of ECU.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE VECTORING AWD SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.

C409702C02
2,0.333 2.417,0.583 0.417,0.25 5.438,0.615 5.854,0.865 0.417,0.25 3.021,1.333 3.292,0.563 3.292,0.563 3.458,0.563 true 6.104,1.625 6.396,2.073 6.396,2.073 6.563,2.073 true 1.365,1.604 1.656,2.229 1.656,2.229 1.823,2.229 true 0.698,2.26 0.865,2.26 0.865,2.26 1.219,1.604 true 0.156,0.052 0.469,0.25 0.313,0.198 10 false *a 2.115,0.385 2.427,0.583 0.313,0.198 10 false N5 5.49,0.667 5.938,0.906 0.448,0.24 10 false G114 1.875,2.167 2.396,2.354 0.521,0.188 10 false CANH 6.625,2 7.156,2.219 0.531,0.219 10 false BAT 0.302,2.188 0.833,2.406 0.531,0.219 10 false CANL 3.521,0.49 4.052,0.708 0.531,0.219 10 false GND 4.813,0.656 5.125,0.854 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N5-6 (CANH) - N5-5 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
N5-6 (CANH) - N5-4 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N5-5 (CANL) - N5-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N5-6 (CANH) - G114-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N5-5 (CANL) - G114-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OCCUPANT DETECTION ECU (w/ Occupant Classification System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406388C07
1.479,0.135 1.906,0.385 0.427,0.25 1.521,1.865 1.979,2.115 0.458,0.25 2.656,3.052 2.406,3.052 2.406,3.052 2.24,2.885 true 0.646,0.333 0.958,0.531 0.313,0.198 10 false *a 0.677,1.865 0.99,2.063 0.313,0.198 10 false *b 1.573,0.177 1.885,0.375 0.313,0.198 10 false S21 1.583,1.906 2.167,2.094 0.583,0.188 10 false G114 2.74,2.979 3.052,3.177 0.313,0.198 10 false BAT
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of DLC3


Disconnect the occupant detection ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S21-5 - S21-4 R - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S21-5 - S21-10 R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S21-4 - S21-10 SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S21-5 - G114-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S21-4 - G114-16 (BAT) SB - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SWING GRILLE ACTUATOR ASSEMBLY (w/ Grille Shutter System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM (for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C409703C01
1.5,0.25 1.917,0.5 0.417,0.25 1.917,1.167 2.25,1.583 2.25,1.583 2.417,1.583 true 2.052,1.063 2.448,0.667 2.448,0.667 2.615,0.667 true 0.938,1.552 1.104,1.552 1.104,1.552 1.313,1.146 true 1.104,1.75 1.271,1.75 1.271,1.75 1.583,1.146 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.573,0.292 1.885,0.49 0.313,0.198 10 false A85 0.667,1.469 0.979,1.667 0.313,0.198 10 false +B 0.75,1.677 1.219,1.875 0.469,0.198 10 false GND 2.5,1.51 2.969,1.708 0.469,0.198 10 false CANN 2.677,0.594 3.146,0.792 0.469,0.198 10 false CANP
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Disconnect the swing grille actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A85-6 (CANP) - A85-5 (CANN) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A85-6 (CANP) - A85-3 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A85-5 (CANN) - A85-3 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A85-6 (CANP) - A85-1 (+B) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A85-5 (CANN) - A85-1 (+B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C325480C48
1.521,0.365 1.927,0.615 0.406,0.25 1.427,2.292 1.792,2.542 0.365,0.25 2.417,1.854 2.583,1.854 2.583,1.854 2.771,1.479 true 1.75,4.25 1.917,4.25 1.917,4.25 2.313,3.604 true 2.521,2.104 2.688,2.104 2.688,2.104 2.896,1.458 true 0.667,2.583 0.833,2.583 0.833,2.583 1.073,3.083 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.604,0.406 2.063,0.604 0.458,0.198 10 false R18 1.49,2.333 1.948,2.531 0.458,0.198 10 false R19 1.958,1.781 2.458,1.99 0.5,0.208 10 false CANP 1.385,4.177 1.875,4.375 0.49,0.198 10 false GND 2.073,2.021 2.573,2.229 0.5,0.208 10 false CANN 0.479,2.51 0.969,2.708 0.49,0.198 10 false B
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R18-39 (CANP) - R18-40 (CANN) L - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R18-39 (CANP) - R19-10 (GND) L - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R18-40 (CANN) - R19-10 (GND) R - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R18-39 (CANP) - R19-1 (B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R18-40 (CANN) - R19-1 (B) R - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369144C55
1.5,0.167 1.917,0.417 0.417,0.25 1.552,2.688 1.719,2.688 1.719,2.688 1.854,2.073 true 2.823,1.719 2.823,0.969 2.823,0.969 2.656,0.969 true 0.635,1.729 0.75,0.833 0.75,0.833 0.917,0.833 true 1.719,2.885 1.885,2.885 1.885,2.885 2.052,2.073 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.594,0.208 1.906,0.406 0.313,0.198 10 false N25 0.979,0.76 1.292,0.958 0.313,0.198 10 false +B 2.198,0.896 2.625,1.094 0.427,0.198 10 false GND 1.115,2.615 1.594,2.823 0.479,0.208 10 false CANH 1.302,2.802 1.781,3.01 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N25-11 (CANH) - N25-12 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
N25-11 (CANH) - N25-4 (GND) GR - LA HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N25-12 (CANL) - N25-4 (GND) W - LA LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N25-11 (CANH) - N25-1 (+B) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N25-12 (CANL) - N25-1 (+B) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher