Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Open in Bus 4 Main Bus Line  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Open in CAN main bus wire

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

No. 1 CAN junction connector

·

No. 4 CAN junction connector

·

No. 6 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C387410E05
5.25,1.052 5.708,1.25 0.458,0.198 10 false G70 5.25,1.208 7.156,1.667 1.906,0.458 10 false Airbag Sensor Assembly 5.813,0.979 6.271,1.177 0.458,0.198 10 false CANL 5.802,0.375 6.26,0.573 0.458,0.198 10 false CANH 5.552,0.396 6.01,0.594 0.458,0.198 10 false 26 5.542,0.76 6,0.958 0.458,0.198 10 false 27 3.896,0.344 4.354,0.542 0.458,0.198 10 false 2 3.896,0.75 4.354,0.948 0.458,0.198 10 false 8 3.208,0.333 3.667,0.531 0.458,0.198 10 false 4 3.198,0.75 3.656,0.948 0.458,0.198 10 false 10 3.01,1.073 3.469,1.271 0.458,0.198 10 false G104 3,1.198 4.25,1.667 1.25,0.469 10 false No. 4 CAN Junction Connector 1.365,0.333 1.823,0.531 0.458,0.198 10 false 9 1.375,0.719 1.833,0.917 0.458,0.198 10 false 20 1.365,3.115 1.823,3.313 0.458,0.198 10 false 21 1.385,2.75 1.844,2.948 0.458,0.198 10 false 10 0.448,3.427 0.906,3.625 0.458,0.198 10 false G96 0.427,3.583 1.719,4 1.292,0.417 10 false No. 1 CAN Junction Connector 3.021,3.427 3.479,3.625 0.458,0.198 10 false M31 3.01,3.604 4.24,4.104 1.229,0.5 10 false No. 6 CAN Junction Connector 5,3.469 5.458,3.667 0.458,0.198 10 false G72 5.031,3.615 7.021,4.094 1.99,0.479 10 false Central Gateway ECU (Network Gateway ECU) 5.563,3.146 6.021,3.344 0.458,0.198 10 false 7 5.563,2.75 6.021,2.948 0.458,0.198 10 false 22 3.906,3.177 4.365,3.375 0.458,0.198 10 false 9 3.885,2.76 4.344,2.958 0.458,0.198 10 false 3 3.208,3.146 3.667,3.344 0.458,0.198 10 false 10 3.25,2.75 3.708,2.948 0.458,0.198 10 false 4 5.813,2.771 6.271,2.969 0.458,0.198 10 false CA2H 5.813,3.385 6.271,3.583 0.458,0.198 10 false CA2L

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.

C382852C44
1.052,1.24 1.458,1.49 0.406,0.25 3.844,0.594 4.094,0.594 4.094,0.594 4.094,1.375 true 3.854,2.135 4.104,2.135 4.104,2.135 4.104,1.719 true 4.021,0.385 4.271,0.385 4.271,0.385 4.271,1.385 true 4.031,2.385 4.281,2.385 4.281,2.385 4.281,1.719 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.125,1.281 1.625,1.521 0.5,0.24 10 false G96 3.281,0.521 3.948,0.76 0.667,0.24 10 false CANH*b 3.313,2.052 3.979,2.292 0.667,0.24 10 false CANL*b 3.427,0.292 4.094,0.531 0.667,0.24 10 false CANH*c 3.51,2.313 4.177,2.552 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to No. 6 CAN Junction Connector - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G96-9 (CANH) - G96-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
G96-10 (CANH) - G96-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C387413C64
0.365,1.271 0.771,1.5 0.406,0.229 2.167,0.375 2.333,0.375 2.333,0.375 3.313,1.302 true 2.219,2.417 2.385,2.417 2.385,2.417 3.313,1.573 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false M31 1.646,0.313 2.198,0.49 0.552,0.177 10 false CANH*b 1.719,2.354 2.271,2.531 0.552,0.177 10 false CANL*b 4.979,0.208 5.531,0.385 0.552,0.177 10 false CANH*c 4.677,2.385 5.229,2.563 0.552,0.177 10 false CANL*c
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 1 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M31-3 (CANH) - M31-9 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M31-4 (CANH) - M31-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

4.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.

C387413C66
0.365,1.271 0.771,1.5 0.406,0.229 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 4.917,0.26 4.667,0.26 4.667,0.26 3.792,1.323 true 4.615,2.438 4.365,2.438 4.365,2.438 3.833,1.615 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.396,1.302 0.854,1.563 0.458,0.26 10 false G104 1.375,0.594 1.927,0.771 0.552,0.177 10 false CANH*b 1.438,1.979 1.99,2.156 0.552,0.177 10 false CANL*b 4.979,0.208 5.531,0.385 0.552,0.177 10 false CANH*c 4.667,2.354 5.219,2.531 0.552,0.177 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to No. 1 CAN Junction Connector - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G104-2 (CANH) - G104-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag sensor assembly
G104-4 (CANH) - G104-10 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Airbag sensor assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the M31 No. 6 CAN junction connector.


b.
C368242C37
1.417,0.24 1.958,0.458 0.542,0.219 1.76,1.802 1.958,1.802 1.958,1.802 2.125,1.292 true 2.229,1.104 2.292,0.552 2.292,0.552 2.563,0.552 true 1.552,0.271 2.01,0.469 0.458,0.198 10 false G72 2.625,0.479 3.083,0.677 0.458,0.198 10 false CA2L 1.375,1.75 1.833,1.948 0.458,0.198 10 false CA2H 0.052,0.063 0.51,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-22 (CA2H) - G72-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the G104 No. 4 CAN junction connector.


b.
B532758C01
1.479,0.135 1.917,0.458 0.438,0.323 2.052,1.344 2.479,0.49 2.479,0.49 2.656,0.49 true 2.156,1.396 2.531,1.813 2.531,1.813 2.708,1.813 true 1.563,0.219 2.021,0.417 0.458,0.198 10 false G70 0.156,0.115 0.615,0.313 0.458,0.198 10 false *a 2.698,0.406 3.156,0.604 0.458,0.198 10 false CANH 2.771,1.729 3.229,1.927 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

w/ Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION

w/o Occupant Classification System:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-26 (CANH) - G70-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE CAN MAIN WIRE AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)