Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus wire or connector

·

Combination meter assembly

·

Central gateway ECU (network gateway ECU)

·

No. 1 CAN junction connector

·

No. 5 CAN junction connector

·

No. 7 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C387410E04
5.406,1.083 5.865,1.281 0.458,0.198 10 false G72 5.49,3.688 6.656,4.271 1.167,0.583 10 false Combination Meter Assembly 5.813,0.979 6.271,1.177 0.458,0.198 10 false CA5L 5.802,0.375 6.26,0.573 0.458,0.198 10 false CA5H 5.552,0.396 6.01,0.594 0.458,0.198 10 false 15 5.542,0.76 6,0.958 0.458,0.198 10 false 16 3.885,0.344 4.344,0.542 0.458,0.198 10 false 11 3.885,0.781 4.344,0.979 0.458,0.198 10 false 22 3.271,0.344 3.729,0.542 0.458,0.198 10 false 9 3.219,0.771 3.677,0.969 0.458,0.198 10 false 20 3.01,1.073 3.469,1.271 0.458,0.198 10 false G105 3.021,1.26 4.271,1.729 1.25,0.469 10 false No. 5 CAN Junction Connector 1.333,0.365 1.792,0.563 0.458,0.198 10 false 3 1.313,0.76 1.771,0.958 0.458,0.198 10 false 14 1.313,3.156 1.771,3.354 0.458,0.198 10 false 12 1.323,2.76 1.781,2.958 0.458,0.198 10 false 1 0.448,3.427 0.906,3.625 0.458,0.198 10 false G96 0.427,3.583 1.667,4.01 1.24,0.427 10 false No. 1 CAN Junction Connector 3.021,3.427 3.479,3.625 0.458,0.198 10 false N52 3.01,3.604 4.229,4.063 1.219,0.458 10 false No. 7 CAN Junction Connector 5.469,3.51 5.927,3.708 0.458,0.198 10 false G18 5.406,1.26 6.75,1.813 1.344,0.552 10 false Central Gateway ECU (Network Gateway ECU) 5.563,3.146 6.021,3.344 0.458,0.198 10 false 25 5.615,2.75 6.073,2.948 0.458,0.198 10 false 9 3.875,3.156 4.333,3.354 0.458,0.198 10 false 8 3.875,2.75 4.333,2.948 0.458,0.198 10 false 2 3.271,3.146 3.729,3.344 0.458,0.198 10 false 7 3.25,2.75 3.708,2.948 0.458,0.198 10 false 1 5.813,2.771 6.271,2.969 0.458,0.198 10 false CANH 5.813,3.385 6.271,3.583 0.458,0.198 10 false CANL


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.

C382852C41
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 2.792,0.177 3.042,0.177 3.042,0.177 3.042,1.375 true 2.885,2.552 3.052,2.552 3.052,2.552 3.052,1.719 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.115,1.292 1.615,1.531 0.5,0.24 10 false G96 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 2.24,0.094 2.906,0.333 0.667,0.24 10 false CANH*c 2.365,2.479 3.031,2.719 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 7 CAN Junction Connector
*c to No. 5 CAN Junction Connector - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G96-1 (CANH) - G96-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 7 CAN junction connector
G96-3 (CANH) - G96-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 5 CAN junction connector CAN main wire) B
NG (No. 7 CAN junction connector CAN main wire) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 5 CAN junction connector.

C382852C42
1.052,1.24 1.458,1.49 0.406,0.25 3.854,0.385 4.104,0.385 4.104,0.385 4.104,1.385 true 3.854,2.365 4.104,2.365 4.104,2.365 4.104,1.698 true 4.604,0.365 4.438,0.365 4.438,0.365 4.438,1.365 true 4.615,2.365 4.448,2.365 4.448,2.365 4.448,1.698 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.104,1.292 1.604,1.531 0.5,0.24 10 false G105 3.302,0.292 3.969,0.531 0.667,0.24 10 false CANH*b 3.302,2.292 3.969,2.531 0.667,0.24 10 false CANL*b 4.656,0.292 5.323,0.531 0.667,0.24 10 false CANH*c 4.698,2.292 5.365,2.531 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G105-9 (CANH) - G105-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
G105-11 (CANH) - G105-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G105 No. 5 CAN junction connector.


b.
C368242C41
1.417,0.24 1.958,0.458 0.542,0.219 1.479,1.271 1.594,1.844 1.594,1.844 1.76,1.844 true 1.573,1.281 1.885,0.646 1.885,0.646 2.052,0.646 true 1.563,0.281 2.021,0.479 0.458,0.198 10 false G72 2.125,0.594 2.583,0.792 0.458,0.198 10 false CA5L 1.813,1.781 2.271,1.979 0.458,0.198 10 false CA5H 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-15 (CA5H) - G72-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 7 CAN junction connector.

C387413C68
0.365,1.271 0.823,1.521 0.458,0.25 1.833,1.135 2,1.135 2,1.135 2.448,1.333 true 1.865,1.729 2.031,1.729 2.031,1.729 2.417,1.563 true 1.938,0.656 2.104,0.656 2.104,0.656 2.885,1.344 true 2.01,2.052 2.177,2.052 2.177,2.052 2.906,1.563 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.438,1.323 0.802,1.479 0.365,0.156 10 false N52 1.313,1.073 1.865,1.25 0.552,0.177 10 false CANH*b 1.354,1.667 1.906,1.844 0.552,0.177 10 false CANL*b 1.417,0.594 1.969,0.771 0.552,0.177 10 false CANH*c 1.469,1.979 2.021,2.156 0.552,0.177 10 false CANL*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Combination Meter Assembly - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
N52-1 (CANH) - N52-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
N52-2 (CANH) - N52-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.

Reconnect the N52 No. 7 CAN junction connector.


b.
C406366C08
1.5,0.125 1.885,0.385 0.385,0.26 1.375,2.042 1.156,2.042 1.156,2.042 0.885,1.385 true 1.646,1.833 1.427,1.833 1.427,1.833 0.885,1.167 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.167 1.885,0.323 0.313,0.156 10 false G18 1.708,1.74 2.198,1.938 0.49,0.198 10 false CANH 1.438,1.917 1.927,2.115 0.49,0.198 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-9 (CANH) - G18-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)