Home › Drivetrain › K120F (MULTIDRIVE / CVT) › OIL COOLER
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0371755 OIL COOLER A

K120F MULTIDRIVE / CVT  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 33493A 1.INSTALL TRANSMISSION OIL COOLER

a.
C402306C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Install the transmission oil cooler to the continuously variable transaxle assembly with the 2 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A)



Hide 32941R 2.CONNECT OIL COOLER INLET HOSE

a.
C405197C01
1.865,3.01 2.146,3.219 2.146,3.219 2.01,3.01 true 1.479,2.344 1.792,2.5 0.313,0.156 10 false *a 2.302,2.5 2.615,2.656 0.313,0.156 10 false *b 2.198,3.135 2.51,3.292 0.313,0.156 10 false *c
*a 2 to 7 mm (0.078 to 0.275 in.)
*b 0 to 3 mm (0 to 0.118 in.)
*c Paint Mark


Connect the oil cooler inlet hose to the transmission oil cooler, and slide the hose clip to secure the hose.

NOTICE:
·

Make sure to slide the oil cooler inlet hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the oil cooler inlet hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.




Hide 32942N 3.CONNECT NO. 1 OIL COOLER OUTLET HOSE

a.
C405200C01
1.854,2.927 2.219,3.125 2.219,3.125 2.01,2.927 true 1.427,2.24 1.75,2.438 0.323,0.198 10 false *a 2.292,2.427 2.604,2.625 0.313,0.198 10 false *b 2.24,3.031 2.552,3.229 0.313,0.198 10 false *c
*a 2 to 7 mm (0.078 to 0.275 in.)
*b 0 to 3 mm (0 to 0.118 in.)
*c Paint Mark


Connect the No. 1 oil cooler outlet hose to the transmission oil cooler, and slide the hose clip to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler outlet hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the No. 1 oil cooler outlet hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.




Hide 16264D 4.CONNECT NO. 2 WATER BY-PASS HOSE

a.
C407600C01
2.292,2.688 2.177,2.271 2.177,2.271 2.469,2.698 false 2.521,3.156 2.833,3.313 0.313,0.156 10 false *a 2.073,2.073 2.385,2.229 0.313,0.156 10 false *b 1.375,2.24 1.688,2.396 0.313,0.156 10 false *c
*a 2 to 7 mm (0.078 to 0.275 in.)
*b Paint Mark (LH Side of Vehicle)
*c 120° (Claw of Hose Clip Location)


Connect the No. 2 water by-pass hose to the transmission oil cooler and slide the hose clip to secure the hose.

NOTICE:
·

Make sure to slide the No. 2 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.

·

Align the hose paint mark the position shown in the illustration.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.




Hide 16261G 5.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the transmission oil cooler and slide the hose clip to secure the hose.

C405181C01
4.792,0.823 5.094,1.208 5.094,1.208 4.813,0.979 true 4.531,1.365 4.771,1.615 0.24,0.25 10 false *c 5.333,0.771 5.646,0.927 0.313,0.156 10 false *b 5.125,1.115 5.438,1.313 0.313,0.198 10 false *a
*a Paint Mark (Upper Side of Vehicle) *b 2 to 7 mm (0.078 to 0.275 in.)
*c 120° (Claw of Hose Clip Location) - -


NOTICE:
·

Make sure to slide the No. 1 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the No. 1 water by-pass hose with the paint mark of the transmission oil cooler.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.




Hide 6.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 7.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 53737D 8.INSTALL FRONT FENDER APRON SEAL LH

Hide 51420 9.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 10.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53896B 11.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 12.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH